Avalue Technology RIPAC-10P3 User manual

Part No. E2017RP13A0R
RIPAC-10P3
10.1”TFT Mini POS
Quick Reference Guide
1st –11 October 2022
Copyright Notice
Copyright 2022 Avalue Technology Inc., ALL RIGHTS RESERVED.

RIPAC-10P3
2 RIPAC-10P3 Quick Reference Guide
FCC Statement
THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE.
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS
FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST
HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A
COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN
RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED IN
ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE
HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO
CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
Notice
This guide is designed for experienced users to setup the system within the shortest time.
For detailed information, please always refer to the electronic user's manual.
Copyright Notice
Copyright 2022 Avalue Technology Inc., ALL RIGHTS RESERVED.
No part of this document may be reproduced, copied, translated, or transmitted in any form
or by any means, electronic or mechanical, for any purpose, without the prior written
permission of the original manufacturer.
Brand and product names are trademarks or registered trademarks of their respective
owners.
Disclaimer
Avalue Technology Inc. reserves the right to make changes, without notice, to any product,
including circuits and/or software described or contained in this manual in order to improve
design and/or performance. Avalue Technology assumes no responsibility or liability for the
use of the described product(s), conveys no license or title under any patent, copyright, or
masks work rights to these products, and makes no representations or warranties that
these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified. Applications that are described in this manual are for illustration

Quick Reference Guide
RIPAC-10P3 Quick Reference Guide
3
purposes only. Avalue Technology Inc. makes no representation or warranty that such
application will be suitable for the specified use without further testing or modification.
Life Support Policy
Avalue Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN
LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE PRIOR WRITTEN APPROVAL
OF Avalue Technology Inc.
As used herein:
1. Life support devices or systems are devices or systems which, (a) are intended for
surgical implant into body, or (b) support or sustain life and whose failure to perform,
when properly used in accordance with instructions for use provided in the labeling, can
be reasonably expected to result in significant injury to the user.
2. A critical component is any component of a life support device or system whose failure to
perform can be reasonably expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
A Message to the Customer
Avalue Customer Services
Each and every Avalue’s product is built to the most exacting specifications to ensure
reliable performance in the harsh and demanding conditions typical of industrial
environments. Whether your new Avalue device is destined for the laboratory or the factory
floor, you can be assured that your product will provide the reliability and ease of operation
for which the name Avalue has come to be known.
Your satisfaction is our primary concern. Here is a guide to Avalue’s customer services. To
ensure you get the full benefit of our services, please follow the instructions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions, you can
easily find answers in your product documentation. These answers are normally a lot more
detailed than the ones we can give over the phone. So please consult the user’s manual
first.
To receive the latest version of the user’s manual; please visit our Web site at:
http://www.avalue.com.tw/

RIPAC-10P3
4 RIPAC-10P3 Quick Reference Guide
Content
1. Getting Started ........................................................................................................5
1.1 Safety Precautions....................................................................................................5
1.2 Packing List...............................................................................................................5
1.3 System Specifications...............................................................................................6
1.4 System Overview......................................................................................................9
1.4.1 Top View.................................................................................................................................. 9
1.4.2 Left Side................................................................................................................................... 9
1.4.3 Right Side................................................................................................................................ 9
1.4.4 Bottom ................................................................................................................................... 10
1.4.5 I/O Interface........................................................................................................................... 10
1.5 System Dimensions ................................................................................................11
1.5.1 RIPAC-10P3.......................................................................................................................... 11
2. Hardware Configuration .......................................................................................12
2.1 RIPAC-10P3 Connector Mapping ...........................................................................13
2.1.1 Serial Port Connector 1/2 (COM1/2) ..................................................................................... 13
2.1.2 Cash drawer connector (RJ11).............................................................................................. 13
2.1.3 RJ45 connector (LAN)........................................................................................................... 14
2.2 Installing SD Card...................................................................................................15
3. Peripherals ............................................................................................................16
3.1 Wi-Fi, Bluetooth.......................................................................................................17
3.1.1 Features................................................................................................................................. 17
3.2 NFC.........................................................................................................................18
3.2.1 Features................................................................................................................................. 18
3.3 Thermal Printer .......................................................................................................18
3.3.1 Thermal Printer Specifications............................................................................................... 18
3.4 Second Display.......................................................................................................18
3.4.1 Second Display...................................................................................................................... 18
3.4.2 Second Display Specifications .............................................................................................. 19
4. Hardware Maintenance.........................................................................................20
4.1 Paper Roll Loading..................................................................................................21
4.2 Replacement of Thermal Printer Module.................................................................24

Quick Reference Guide
RIPAC-10P3 Quick Reference Guide
5
1. Getting Started
1.1 Safety Precautions
Warning!
Always completely disconnect the power cord from your
chassis whenever you work with the hardware. Do not
make connections while the power is on. Sensitive
electronic components can be damaged by sudden power
surges. Only experienced electronics personnel should
open the PC chassis.
Caution!
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution,
use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded
bag when they are not in the chassis.
1.2 Packing List
1 x RIPAC-10P3
1 x Power Adapter
1 x Power Cord
2 x Paper Holder

RIPAC-10P3
6 RIPAC-10P3 Quick Reference Guide
1.3 System Specifications
Component
Mother Board
Intel® Celeron® Apollo Lake Platform
CPU
Intel® Celeron® Processor J3455
CPU Cooler (Type)
PLB05508S05H-B
Memory
Onboard 4GB
Adapter
DC 24V/5A 120W
Speaker
2 x 2W Speaker on back
Wireless LAN
IEEE 802.11 a/b/g/n/AC (Realtek RTL8822BE-CG)
Bluetooth
Bluetooth 4.0 + Class 1 (Realtek RTL8822BE-CG)
Operating System
Windows 10 IoT, Android 8.1
NFC
JW-HMNFC-600(optional)
Other Component
SEIKO thermal printer CAPD347D-E
PP-802 V3.0 printer control board
Storage
Solid State Drive
Onboard 128G eMMC
Panel
LCD Panel
10.1” 1280 x 800 K101-IM2BYL02-L 280nits, MIPI interface
5” 1280 x 720 TIANMA TM050JDHG33-00 480nits, MIPI interface, 20,000 Hrs
(customer facing)
Touch Screen
10” Touch
External I/O
Serial Port
2 x RS-232
USB Port
4 x USB3.0
LAN Port
1 x RJ45 Gigabit LAN
Wireless LAN
Antenna
2 x Wireless Antenna
Switch
1 x Power button
Indicator Light
1 x Power LED
Expansion Slots
1 x SD card slot
Others
1 x RJ11(12V / 24V for cash drawer)
1 x Thermal Printer support 58/80mm printing paper (Optional)
Mechanical
Power Type
ATX Mode, +24V DC-In
Power Connector
Type
DC-Jack
Dimension
(L)299.1 x (W)273.2 x (H)128.8 mm
Weight
2Kg

Quick Reference Guide
RIPAC-10P3 Quick Reference Guide
7
Color
Black & Gray, White
OS Support
Windows 10 IoT(64 Bit), Android 8.1(64 Bit)
Reliability
EMI Test
CE/FCC Class B, VCCI, CCC
Safety
All design for this project have to comply with UL / CB
Vibration Test
Random Vibration Operation
1 Test PSD : 0.00454G²/Hz , 1.5 Grms
2 System condition : operation mode
3 Test frequency : 5~500 Hz
4 Test axis : X,Y and Z axis
5 Test time : 30 minutes per each axis
6 IEC60068-2-64 Test Fh
6 Storage : mSATA
Sine Vibration test (Non-operation)
1 Test Acceleration : 2G
2 Test frequency : 5~500 Hz
3 Sweep：1 Oct/ per one minute. (logarithmic)
4 Test Axis : X,Y and Z axis
5 Test time :30 min. each axis
6 System condition : Non-Operating mode
7. Reference IEC 60068-2-6 Testing procedures
Package Vibration Test:
1 Test PSD : 0.026G²/Hz , 2.16 Grms
2 Test frequency : 5~500 Hz
3 Test axis : X,Y and Z axis
4 Test time : 30 minutes per each axis
5 IEC 60068-2-64 Test Fh
Mechanical Shock
Test
1 Wave from : Half Sine wave
2 Acceleration Rate : 10g for operation mode
3 Duration Time : 11ms
4 No. of shock : Z axis 300 times
5 Test Axis : Z axis
6 operation mode
7 Reference IEC 60068-2-27 testing procedures
Test Eb : Shock Test
Drop Test
Package drop test
Reference ISTA 2A, Method : IEC-60068-2-32 Test:Ed
Test Ea : Drop Test

RIPAC-10P3
8 RIPAC-10P3 Quick Reference Guide
1 Test phase : One corner, three edges, six faces
2 Test high : 96.5cm
3 Package weight : 5Kg
4 Test drawing
Operating
Temperature
0°C~40°C
Operating Humidity
40°C @ 95% Relative Humidity, Non-condensing
Storage
Temperature
-10°C~60°C
Note: Specifications are subject to change without notice.

Quick Reference Guide
RIPAC-10P3 Quick Reference Guide
9
1.4 System Overview
1.4.1 Top View
1.4.2 Left Side
1.4.3 Right Side
Printer Door Switch
10.1”LCD
5”LCD
Thermal
Printer
Speaker

RIPAC-10P3
10 RIPAC-10P3 Quick Reference Guide
1.4.4 Bottom
1.4.5 I/O Interface
Connectors
I/O
Function
Note
COM1/2
Serial port connector 1/2 (RS232)
DB-9 male connector
RJ11
Cash drawer connector
LAN
RJ45 connector
USB3.0
4 x USB3.0 connectors
SD card
SD card slot
Kensington Lock
Kensington Security Slot
DC-IN
DC Power-In connector
5.5 x 2.5mm DC Jack
Power Button
Reset

Quick Reference Guide
RIPAC-10P3 Quick Reference Guide
11
1.5 System Dimensions
1.5.1 RIPAC-10P3
(Unit: mm)

RIPAC-10P3
12 RIPAC-10P3 Quick Reference Guide
2.Hardware
Configuration
Note: If you need more information, please visit our website:
http://www.avalue.com.tw

Quick Reference Guide
RIPAC-10P3 Quick Reference Guide
13
2.1 RIPAC-10P3 Connector Mapping
2.1.1 Serial Port Connector 1/2 (COM1/2)
Signal
PIN
PIN
Signal
DCD#_1
1
6
DSR#_1
RXD_1
2
7
RTS#_1
TXD_1
3
8
CTS#_1
DTR#_1
4
9
RING/5V/12V
GND
5
2.1.2 Cash drawer connector (RJ11)
Signal
PIN
GND
1
KICKOUT1
2
CASH_SENSE
3
+12VA_+24VA_CASH
4
KICKOUT2
5
GND
6

RIPAC-10P3
14 RIPAC-10P3 Quick Reference Guide
2.1.3 RJ45 connector (LAN)
Signal
PIN
LAN1_TX0+
1
LAN1_TX0-
2
LAN1_TX1+
3
LAN1_TX2-
4
LAN1_TX2-
5
LAN1_TX1-
6
LAN1_TX3+
7
LAN1_TX3-
8

Quick Reference Guide
RIPAC-10P3 Quick Reference Guide
15
2.2 2BInstalling SD Card
Step 1. Unfasten screw from the cover and take it off.
Step 2. Insert SD Card slot into designated locations (SD Card can be pushed back and forth).

RIPAC-10P3
16 RIPAC-10P3 Quick Reference Guide
3. Peripherals
Note: If you need more information, please visit our website:
http://www.avalue.com.tw

Quick Reference Guide
RIPAC-10P3 Quick Reference Guide
17
3.1 Wi-Fi, Bluetooth
3.1.1 Features
Support 2.4GHz and 5GHz band channels.
20MHz, 40MHz and 80MHz bandwidth transmission.
Compatible with IEEE 802.11a standard to provide wireless 54Mbps data rate.
Compatible with IEEE 802.11b standard to provide wireless 11Mbps data rate.
Compatible with IEEE 802.11g standard to provide wireless 54Mbps data rate.
Compatible with IEEE 802.11n standard to provide wireless 300Mbps data rate.
Compatible with IEEE 802.11ac standard to provide wireless 866.7Mbps data rate.
Operation at 2.4G-2.5GHz and 5.15~5.825GHz frequency band to meet worldwide
regulations.
Bluetooth 4.2 dual mode support: simultaneous LE and BR/EDR.
Compatible with Bluetooth v2.1 and v3.0 systems.
Support Bluetooth 4.2 Low and Energy (LE).
Maximum reliability, throughput and connectivity with automatic data rate switching.
Complies with PCI Express base specification revision 2.1 for WLAN.
Complies with USB with configurable baud rate for Bluetooth
DSSS with DPSK and DQPSK, CCK modulation with long and short preamble.
OFDM with BPSK, QPSK, 16QAM, 64QAM and 256QAM modulation.
Support infrastructure networks via Access Point and ad-hoc network via peer-to-peer
communication.

RIPAC-10P3
18 RIPAC-10P3 Quick Reference Guide
3.2 NFC
3.2.1 Features
NXP NFC Controller
Compliant with ISO/IEC 14443 A/B
Compliant with 15693/18092
Frequency 13.56Mhz
USB interface
3.3 Thermal Printer
3.3.1 Thermal Printer Specifications
Thermal Printer
Printing Method
Thermal Dot Line Printing
Total Dots Per Line
576 Dots
Resolution
(W)8 Dots/mm, (H)8 Dots/mm
Max. Print Speed
200mm/s
Max. Print Width
72mm
Max. Paper Width
80mm
Type of Paper Cutting
Full Cut & Partial Cut
Media Dimensions:
80mm: 79.5 ± 0.5 (W) x 80mm diameter (3.13" ± 0.02” x 3.15")
58mm: 57.5 ± 0.5 (W) x 80mm diameter (2.26" ± 0.02” x 3.15")
3.4 Second Display
3.4.1 Second Display
5”LCD

Quick Reference Guide
RIPAC-10P3 Quick Reference Guide
19
3.4.2 Second Display Specifications
5”Second Display
LCD Type
TFT/Transmissive
Viewing Angle
Full Viewing Angle
Pixel Pitch (W x H)
0.08625x0.08625 mm²
Resolution
1280 x 720
Backlight Type
LED

RIPAC-10P3
20 RIPAC-10P3 Quick Reference Guide
4.Hardware
Maintenance
Note: If you need more information, please visit our website:
http://www.avalue.com.tw