Avantco 177CS11V User manual

User Manual
www.AvantcoEquipment.com 1
Churro Stuffer
Models: 177CS11V, 177CS15V, 177CS20V, 177CS20VKIT,
177CS30V, 177CS30VKIT, 177CS7V
Please read and keep these instructions. Indoor use only.
03/2023
User Manual

User Manual
2 www.AvantcoEquipment.com
General Safety Regulations
WARNING: The warnings, cauons, and instrucons discussed in this instrucon manual cannot cover all possible condions
or situaons that could occur. It must be understood by the operator that common sense and cauon are factors that cannot
be built into this product, but must be supplied by the operator.
Please use this machine according to these cauons. The user should understand all rules. Please carefully read them
before you operate the machine. This machine may cause harm to the health of the operator if the user removes or changes
equipment in the machine.
We are not responsible for any injuries resulng from improper operaon of this machine. Please operate according to
“Operaon Method” instrucons and follow the proper operaon procedures while using. Take care while assembling and
operang in order to avoid scratching skin. Please read the instrucon manual.
• CHECK FOR DAMAGED PARTS. Before using the stuffer, check that all parts are operating properly and perform
the intended functions. Check for binding of moving parts, mounting, and any other conditions that may affect the
operation.
• The Manufacturer declines any responsibility in the case of improper use of the stuffer. Improper use of the stuffer
will VOID the warranty.
• Repair must be done by an authorized dealer. Use only factory original parts and accessories. Modification of the
stuffer will VOID the warranty.
• Be sure the stuffer is stable during use.
• NEVER operate the stuffer with the gear housing cover open or removed.
• WEAR EYE PROTECTION! Everyday eye glasses are not safety glasses. Safety glasses conform to ANSI Z87.1
requirement. Note: Approved safety glasses have Z87 printed or stamped on them.
• Do not use outdoors.
• SAVE THESE INSTRUCTIONS.

User Manual
www.AvantcoEquipment.com 3
Assembly and
Installation
PLUNGER ASSEMBLY
1. Slide the Plunger Seal onto the Plunger
(gure 1).
2. Assemble the Pressure Release Valve Kit
onto the Plunger. From the top of the
Plunger, place the Washer onto the Valve
Hole, then insert the Screw through the
Washer and into the Valve Hole. From the
underside of the Plunger, place the Spring
onto the end of the Screw, then place the
Valve Cap onto the end of the Screw and
twist to secure.
3. Screw the Plunger Bolt onto the Plunger
Sha (gure 2).
4. Place the assembled Plunger onto the end
of the Plunger Sha (gure 3).
STUFFER ASSEMBLY
5. Aach the Handle by sliding it onto either
the Fast or the Slow Gear (gure 4).
6. Crank the Handle to bring the Plunger to
the top of the Stuer.
 ...connuedonnextpage

User Manual
4 www.AvantcoEquipment.com
STUFFER ASSEMBLY connued
7. Rest Canister’s Boom Brackets onto the Canister
Mounts inside the Housing of the Stuer. Pivot the
Canister fully into the Stuer Housing, snapping the To p
Brackets into the Canister Mounts (gure 5).
8. Insert the Stung Funnel of choice through the Front
Ring Nut. Screw the Front Ring Nut and Stung Funnel
onto the mouth of the Canister unl snug. DO NOT
OVERTIGHTEN the Front Ring Nut, as it may damage the
Funnel (gure 6).
9. Thoroughly coat the inside of the Canister with a food-
grade lubricant prior to use (gure 7).

User Manual
www.AvantcoEquipment.com 5
Disassembly and Cleaning
NOTE: BE SURE TO CLEAN ALL PARTS IMMEDIATELY AFTER USE.
1. Remove the Stung Funnel by unscrewing the Front Ring Nut and pulling the Funnel out.
2. Turn the Handle unl the Plunger comes up and out of the Canister.
3. Pivot the Canister outward, then pull the Canister up to remove the Canister from the Stuer Housing.
4. Unscrew the Plunger from the Plunger Sha.
5. Disassemble the pressure release valve from the plunger.
6. Remove the plunger seal from the plunger.
7. Wash all parts that have come in contact with churro mixture in hot soapy water.
8. Rinse and thoroughly dry all parts immediately.
9. Sterilize as needed.
10. Fully lubricate the Sha, Canister, Pressure-Release Valve components, and the Front Ring Nut with a food-grade lubricant
before and aer each use.

User Manual
6 www.AvantcoEquipment.com
Stuffing Instructions
CAUTION! When the plunger is pulled out of the Canister,
RELEASE THE HANDLE SLOWLY! Pressure or gravity
could cause the Handle to spin back slightly and cause
injury.
NOTE: Apply a food-grade lubricant to the inside of the
Canister before lling with the churro mixture.
1. Tilt out the Canister.
2. Fill the Canister with the churro mixture and seasoning mixture (gure 8).
3. Press the mixture down into the Canister rmly to release any trapped air.
4. Pivot the Canister back into the upright posion and snap the Top
Brackets onto the Canister Mounts.
5. Turn the Handle unl the Plunger comes in contact with the churro mixture and the mixture is
ready to extrude out of the end of the Stung Funnel.
6. Connue turning unl extruded Churro mixture is desired length.

User Manual
www.AvantcoEquipment.com 7
5⁄8"
7⁄8"
1¼"
1½"
Exploded Diagram and Parts List
Part # Description
1Handle
2Plunger
3Plunger Seal
4 Pressure Release Valve (4 Piece Set)
5 (1) Hollow Churro Tube
6 Stainless Steel Canister
7 Front Ring Nut
8 Canister Mounting Hardware Kit (4 Sets)
9Plunger Shaft
10 Plunger Bolt
11 Gear Housing Cover with Hardware Kit
12 Gear Housing Cover Bottom Plate with
Hardware Kit
13 Gear Housing with Hardware Kit
14 Main Driving Gear
15 Slow Speed Control Gear
16 Fast Speed Control Gear
17 Rubber Foot (4 Piece Set)
18 Butterfly Screw
19 (1) 11/16" Non-Hollow Churro Tube
20 (1) 5/16" Non-Hollow Churro Tube
21 (1) 1" Non-Hollow Churro Tube
5⁄8"
7⁄8"
1¼"
1½"
11/16”
5⁄8"
7⁄8"
1¼"
1½"
19
5/16”
5⁄8"
7⁄8"
1¼"
1½"
20
1”
5⁄8"
7⁄8"
1¼"
1½"
21