Avantco 755 User manual

English
Operator’s Manual
2016-
755/760

2
755/760i
TABLE OF CONTENTS
Table of contents............................................................2
Introduction..................................................................3
Safety instructions.........................................................4
Warranty....................................................................6
Description of the loader..............................................7
Engine identification................................................8
Loader identification................................................8
Main parts of the loader...........................................8
Signs and decals.......................................................9
Technical specification...........................................10
Fuel requirements.................................................11
Engine oil requirements.........................................11
Tyres....................................................................11
Emission control information................................11
Auxiliary hydraulics oil flow....................................11
Load diagram.........................................................12
Transporting instructions and tie down points......12
Operating instructions................................................13
Operating controls................................................14
Control of loader boom, auxiliary
hydraulics and other functions...............................15
Attachment control switch pack...........................15
Dashboard.............................................................16
Indicatorlights........................................................16
Gauges and switches on the dashboard.................17
Controls in the footwell........................................17
Seat belt and seat adjustments................................17
Suspension seat.....................................................17
Air Suspension seat................................................17
Drive speed range selection switch.......................18
Parking brake switch.............................................18
Seat heater.............................................................18
Battery disconnect switch.....................................18
Telescopic boom...................................................18
Smooth drive.........................................................18
Boom self levelling.................................................19
Boomfloating.........................................................19
Joystick..................................................................19
Engine block heater...............................................19
Trailer coupling......................................................19
Extra counterweights............................................19
Work light kit........................................................19
Headlight, beacon, blinker & reflector kit.............19
Tilt adapter............................................................20
Drive release valve.................................................20
Anti slip valve.........................................................20
Extra auxiliary hydraulics outlets, front and rear.....20
Warning beacon....................................................20
Starting the engine.................................................21
Stopping the engine...............................................21
Drive control.........................................................22
Steering of the machine.........................................23
Loader control.......................................................23
Using the auxiliary hydraulics................................23
Requirements for attachments..............................24
Coupling the attachments.....................................24
Hydraulic attachment coupling plate.....................24
Coupling the hydraulic hoses of the attachment....25
Make sure that the attachment
is locked to the loader..........................................25
Releasing the pressure of hydraulic system...........25
Cabs......................................................................26
Service and maintenance instructions......................28
Safety instructions for maintenance.......................28
Installing of service support and frame lock..........28
Daily inspections...................................................29
Maintenance schedule...........................................29
Cleaning of the machine........................................30
Greasing of the machine........................................30
Battery check.........................................................30
Hydraulic oil level..................................................30
Check coolant level...............................................30
Hydraulic oil filter change......................................30
Hydraulic oil change..............................................30
Check and tightening of bolts, nuts etc.................31
Check of hydraulic pressure..................................31
Adjustment of hydraulic pressure..........................31
Adjust and change of slide pads on telescopic boom ...32
Calibration of load sensor......................................32
Clean air filter element..........................................32
Water separator and fuel filter................................33
Service, engine.......................................................33
Engine diagnostics.................................................33
Fuses....................................................................33
Hydraulic oil cooler fan fuse..................................34
Jump start and auxiliary power..............................34
Refueling................................................................34
Storage of the machine..........................................34
Metal structures of the loader...............................34
Greasing points......................................................35
Light bulbs.............................................................35
Filters....................................................................36
Troubleshooting....................................................37
Service history..............................................................38
EC Declaration of Conformity....................................39
Original instructions
Table of contents

3
755/760i
Introduction
AVANT TECNO OY wants to thank you for purchasing this AVANT loader. It is the result of Avant’s long experience
in design and manufacturing of compact loaders. We ask you that you read and understand the contects of this manual
completely before operating the loader. This operator’s manual is intended to help you to:
• operate this machine safely and efficiently
• observe and prevent situations that may cause a risk or danger
• keep the machine in good condition and its life span as long as possible
Following symbols are used throughout this Manual to point out important things related to safety:
This safety symbol indicates important safety instructions in this Manual. It warns of an immediate
hazardous situation that can cause serious personal injuries or property damages. Read carefully the
warning text next to this symbol and make sure that all other operators are aware of the warnings as
well. It is a question of safety of persons.
This attention symbol indicates important instructions concerning correct use and maintenance of this
machine. If these instructions are not followed, the consequence can be breakdown of the machine or
property damage.
Contact your local AVANT dealer for any questions, service, spare parts or about any problems that may occur with the
operation of your machine.
Keep this Operators Manual with the machine at all times. If this Manual gets lost, ask for a new copy from your Avant
dealer. Remember also to give this Manual to the new owner when the machine changes ownership.
Introduction
In addition to this Operator’s
manual of the loader, ensure that
you have received and read also the
original Engine owner’s manual. The
instructions concerning the engine,
must be followed. If conflicting
information is found, the information
shown in the Operator’s Manual of the
loader must be followed.
Each attachment is accompanied by its
own respective Operator’s Manual.
The manual will show important
information related to safety, and
how to attach, use, and maintain each
attachment correctly.
Intended use
AVANT 755/760i is an articulated compact loader, designed and manufactured for both professional and private use.
The loader can be equipped with attachments offered by Avant Tecno Oy, which enables doing of several different jobs.
Because of this multi purpose nature of the machine and the various attachments and tasks, read always not only this
Manual but also the Operators Manual of the attachment, and follow all instructions. Every person who has to do with
this machine must follow work safety regulations, all other generally accepted rules related to work health and safety,
and all road traffic regulations.
Remember that safety consists of several factors. The loader, equipped with an attachment is very powerful and can
cause serious personal injuries or property damages if it is operated in a wrong or careless way. Do not operate an
attachment unless you have familiarised yourself with the use of it and the eventual dangers related to it.
This loader has been designed to require as little maintenance as possible. The operator can perform the routine
maintenance operations. There are however more demanding service operations that can be done by professional
service personnel only. It is allowed to perform service operations only when wearing appropriate protective equipment.
Original spare parts must be used. Familiarise yourself with the service and maintenance instructions in this Manual.
Contact your local AVANT dealer, if you are uncertain of anything concerning the operation and maintenance of this
loader, or for any questions, service or spare parts.

4
755/760iSafety instructions
Safety first
An incorrect or careless operation of
the loader may be the origin of a serious
accident. Before putting the machine
into operation, familiarise yourself with
the use of the machine and read and
understand this Operators Manual as
well as the safety instructions.
Understand the limitations of speed, braking, steering and
stability as well as loading capacity of the machine before
starting operation. Make sure that every one who operates
or works with this equipment is familiar with these safety
precautions.
If you have no previous experience of the machine, make
sure to do all testing at a safe and open place with no
persons in the area of operation.
Read this Operators Manual, and also the
Operators Manual of the attachment(s) and
other safety instructions before starting
operation
General instructions
1. Remember the correct working position. When driving
be comfortably seated in the driver´s seat, keep your
feet in their proper place in the footwell and at least
one hand on the steering wheel.
2. When seated, always keep the seat belt fastened and
keep hands and feet inside the operator’s area.
3. Start the operation slowly and carefully. Practice
driving of the machine at a safe and open place before
connecting any attachment, follow the instructions in
this Manual.
4. Operate the control levers with ease and without
hesitation. Avoid abrupt movements when handling
the load, in order to prevent the load from falling and
to keep the machine stable.
5. Keep away from the danger zone of the lifted boom
and don’t let anyone go there.
6. Keep your hands, feet and clothing away from all
moving parts, hydraulic components and hot surfaces.
7. Make sure that there is enough open space around the
machine for safe driving.
8. Do not transport the load with the boom lifted. Always
carry bucket or attachment as low as possible, and put
the load down whenever you leave the machine.
9. Before leaving driver’s seat:
• Lower the loader boom and place attachment
flat on ground
• Engage the parking brake
• Stop the engine, remove the ignition key
10. It is not allowed to transport persons with this machine.
Do not transport or lift persons in the bucket or in any
other attachment. Lifting of persons is only allowed
with the attachment designed for this purpose: Avant
Leguan 50, following the instructions in the Operators
Manual of Leguan 50.
11. Do not exceed rated operating capacity. Familiarise
yourself with and follow the load diagrams in this
Manual.
12. When turning with the machine, remember that the
driver´s seat extends beyond the turning radius of the
wheels (collision risk).
13. Do not operate the loader in an explosive environment
or in a place where dust or/and gases can create a fire
or explosion hazard.
14. Keep the engine area clean of flammable materials.
15. Read the transportation instructions on page 12.
16. Switch off the battery disconnect switch whenever
leaving the machine unattended.
17. Follow all inspection, service and maintenance
instructions. If you notice any faults or damages on
the machine, these must be repaired before starting
operation.
18. Before any maintenance or repair operation always
stop the engine, lower the boom down and release
pressure from hydraulic system. Read safety
instructions for maintenance on page 28.
19. Do not let any person operate this loader who has not
read safety instructions and is not familiar with the
safe and correct use of this loader.
Operation on gradients
20. Load, unload, and turn on flat level ground only. Drive
slowly on uneven terrains. Do not drive on too steep
a gradient - watch out for ditches, manholes and steep
gradients.
21. Do not park the machine on a surface with a gradient.
Should this be necessary, engage the parking brake and
preferably turn the machine sideways and put down
the load. If needed, use chocks behind the wheels.
22. Use low speed range when driving on hills or uneven
terrain.

5
755/760i Safety instructions
Handling of heavy loads and load sensor
The loader is equipped with a load sensor system. It
gives an audible warning signal and at the same time an
indicator lights in the dashboard when there is a risk that
the machine tips over its front axle. When the system gives
a warning signal the load that is being lifted is too heavy in
relation with the lift capacity of the loader. In this case one
has to either put more counterweights on the loader or
relieve the load that is being lifted.
When the load sensor starts to warn, there is
a risk that the machine tips over its front axle.
In this case stop lifting of the boom, retract
the telescopic boom and lower down the
boom slowly. When the load sensor is warning
do not steer the machine before the boom is
lowered down close to ground level. Lift the
boom only when the loader chassis is straight.
Keep the load as close to ground as possible.
Never take a heavy load on the loader from
high level – e.g. from truck, shelf etc. – risk of
tipping over!
Always put the load down on the ground
before leaving the machine. When loading,
always keep the loader chassis as straight as
possible.
Personal safety and protective equipment
Wear safe clothing and personal protective equipment
(PPE). Protect yourself against work hazards like noise,
ejecting debris or dust for example.
• Noise level at driver’s seat can exceed
85 dB(A). Wear hearing protection when
working with the loader.
• It is recommended to wear safety
footwear when working with the loader.
• Wear protective gloves when handling
hydraulic hoses.
• Follow regulations regarding protective
equipment. Wear eye protection and
hard hat or other protective equipment
as needed.
Read Operators Manual of the attachment for more
information about protective equipment needed in the
work.
Safety frame (ROPS) and safety canopy (FOPS)
Safety frame (ROPS) protects the operator
in case the machine tips over. Always fasten
the seat belt in order to stay inside the safety
frame protective area.
The loader is also equipped with a falling
objects protective canopy (FOPS). Never
take off the safety structures, modify them,
or attempt to repair. If damaged, contact
service.
Electric system and handling the battery
Lead acid batteries can produce flammable and explosive
gases. Make sure that the ventilation is sufficient and keep
arcs, sparks, flames and lighted tobacco away from battery.
• Battery contains corrosive sulfuric acid.
• Avoid contact with skin or clothes. If electrolyte
gets on your skin or clothes, flush with a lot of water.
• In case of contact with eyes, flush with a lot of water
for at least 15 minutes and consult a doctor immediately.
• Never charge a frozen battery.
• In order to avoid spark emissions always disconnect
the negative (-) cable first and connect it last.
• Before connecting the battery cables make sure
that the polarity is correct: faulty connection will
seriously damage the electric system of the engine.
• Disconnect the battery before working on the engine or
equipment.
• Read the instructions for jump start on page 33.

6
755/760iWarranty
Avant 755/760i warranty
This warranty specifically applies to the AVANT 755/760i loader only and not to any attachments used with this product.
Any repairs or modifications performed without the prior authorisation of Avant Tecno Oy will cancel this warranty.
During the first two years of operation or first 1000 hours (whichever is the soonest) Avant Tecno Oy warrants to
replace any part or repair any defect which may occur, subject to the terms detailed below:
1) The product has received regular maintenance in accordance with schedules given by the manufacturer.
2) Any damage caused by operation in a negligent manner or exceeding the approved specifications detailed in this
manual is excluded.
3) Avant Tecno Oy accepts no responsibility for interruption to working or any other consequential losses resulting
from any failure of the product.
4) Only Avant Tecno Oy approved replacement or original quality parts shall be used during routine maintenance.
5) Any damage caused by the use of incorrect fuel, lubricants, cooling liquid or cleaning solvents is excluded.
6) The Avant Warranty excludes any consumable parts (e.g. tyres, batteries, filters, belts etc.) except where it can be
clearly shown that these parts were defective on original supply.
7) Any damage caused resulting from the use of attachments not approved for use with this product is excluded.
8) In the event a fault occurs which is attributable to manufacturing or assembly defect you should arrange to return
your AVANT to your authorised dealer for repair. Travel and freight costs are excluded.

7
755/760i Description of the loader
Description of the loader
Identification of the loader
Write down the identification information of your loader in the following fields, it facilitates ordering of spare parts etc.
1. Loader model_____________________________________________
2. Loader serial no.___________________________________________
3. Engine serial no.___________________________________________
Serial number of the loader is printed on the type plate (see page 9), which also indicates the loader model.
Location of engine serial number can be found in the Operators Manual of the engine.
Dealer:____________________________________________________
Contact information:_________________________________________
________________________________________
Loader identification
Loader identification plate is located near the steering wheel
on machines with ROPS canopy and cab L, and near the drive
pedals on machines equipped with a cab LX or DLX.
Engine identification
Engine identification plate is located on the right side of the
valve cover. Further details are shown in the engine operator’s
manual. European 97/68/EC label is located on left side of
engine block, and a supplemental European label is located next
to ECU.

8
755/760iDescription of the loader
Main parts of the loader
Following picture shows the main parts of the loader:
j
k
l
m
n
o
p
q
j
k
l
m
Front frame
On the front frame are mounted: driver’s seat,
operating controls, parking brake, hydraulic control
valves, hydraulic oil tank, auxiliary hydraulics outlet,
front wheels, hydraulic motors and the loader boom
with attachment coupling plate.
Back frame
On the back frame are mounted: engine with
accessories, battery, fuel tank, hydraulic pumps, rear
wheels, hydraulic motors, counterweights.
Articulation joint
Articulation joint connects the front and back frame.
The loader is steered hydraulically by the steering
cylinder which is mounted between the front and
back frames. Hydraulic hoses and electric wires are
conducted through the articulation joint.
Loader boom
Loader boom is mounted on the front frame with
one pivot pin. The attachment coupling plate is
mounted on the lower end of the boom. The boom
is telescopic, extending 700 mm hydraulically.
Hydraulic
connectors
Multi connector
Tank line
Attachment control switch
pack socket (option)
Pressure 2
Pressure 1
n
o
p
q
Attachment coupling plate
Attachments are mounted on the attachment coupling
plate. The locking pins on the plate can be operated
manually (standard) or hydraulically (option).
Auxiliary hydraulics outlet
The hydraulic hoses of hydraulically operated
attachments are mounted on this outlet. The outlet
is equipped with the multi connector quick coupling
system and is double acting: it has two pressure
lines and one tank line. Also the optional attachment
control switch pack socket is mounted on the multi
connector. In addition, as an option, it is also possible
to install a single or double acting auxiliary hydraulics
outlet in the rear of the machine, or a double acting
outlet in the front under the multi connector.
ROPS safety frame
ROPS frame (Roll-over protective structure) complies
with the standard ISO 3471:1994 with Amendment
1:1997 and Technical Corrigendum 1:2000.
FOPS canopy
FOPS canopy (Falling objects protective structure)
mounts on the ROPS. It meets the ISO 3449:2005
(1365 J) criteria.

9
755/760i Description of the loader
Signs and decals
Make sure that the following signs and decals clean, undamaged and readable. If any of these decals is
missing or is unreadable it should be replaced without delay. Ask for new decals from your local Avant
dealer.
j
o
p
m
l
k
n
q
j
o
p
m
l
k
n
q
A411047 A418945
Sound power level / Sound pressure level at driver’s seat
Keep out from the danger zone of
the machine 2 pcs
A417273
A415591
Risk of crushing, keep hands and feet within
the drivers‘ area
Risk of crushing, do not grip the steering
wheel from outside the machine or when
getting into the driver’s seat.
A411456
A411455
A414690
Hot surface,
exhaust outlet
A414244
Pressurised
coolant reservoir
A417272
Hot surface,
A417270
High pressure
accumulator
A414631
(smooth drive
only)

10
755/760iDescription of the loader
Technical specification
Model AVANT 755 AVANT 760i
Length 3080 mm
Width see table on page 11
Height
(with standard wheels) 2060 mm 2110 mm
Ground clearance 252 mm 305 mm
Weight, starting from 1970 kg 2100 kg
Standard wheels 320/60-12 TR 400/50-15 TR
Transmission, drive hydrostatic
Hydraulic oil tank capacity 38 l
Hydraulic oil type ISO VG 46
Auxiliary hydraulics 80 l/min, 225 bar
Turning radius inside/outside 1240 / 2780 mm
Max. lifting height 3100 mm
Max. lifting capacity (hydr.) 2100 kg
Max. tipping load* 1400 kg
Max. breakout force / 50 cm 1700 kg
Sound
pressure level
2000/14/EC L
P
86 dB (A)
Sound power level
2000/14/EC L
W
101 dB (A)
Hand-arm vibration, total
< 2,5 m/s²
Whole-body vibration, max. < 0,5 m/s²
*) Load is measured at 400 mm from the attachment coupling plate,
including attachment weight ( 70 kg ) and with counterweights.
Drive speed and pulling force
Height with cab
26x12.00-12 or
320/60-12 320-55/15 400/50-15 *)
LX Cab 2078 mm 2112 mm 2132 mm
DLX Cab 2105 mm 2139 mm 2169 mm
DLX Cab with AC on the roof 2241 mm 2275 mm 2305 mm
DLX Cab with Lightbar 2301 mm 2335 mm 2365 mm
320/60-12 and
26x12.00-12 320/55-15 400/50-15 31x15.50-15
755 Drive speed 17 km/h 19 km/h -
Pulling force 1330 kp 1240 kp -
760i Drive speed 26 km/h 27 km/h 30 km/h
Pulling force 1880 kp 1750 kp 1600 kp
Model AVANT 755/760i
Engine make and type Kohler KDI 1903 TCR
Function 4-stroke, OHV, four valves/cylinder, Tur-
bocharged, Common rail direct injection
Coolant
Water/50% antifreeze, Freezing point -37C, total 11.6l
Number of cylinders 3
Starter electric
Bore x stroke 88 x 102
Displacement 1861 cm³
Output (ECE R120) 42 kW / 56 hp
Max torque
220 Nm @ 1500 rpm
Fuel Ultra low sulfur diesel fuel
Fuel tank capacity 40 l
Engine oil type API CJ-4 / Low SAPS Euro 6
e.g. Mobil Delvac 1 LE 5W-30
Viscosity 5W-30 (0W-30 below -25 C)
Engine oil capacity Min 5 l max 8,7 l incl. oil filter
Emissions level
EU 97/68/EC Stage 3B, US EPA/CARB Tier 4 Final
Max inclination Max intermittent 30°
Continuous operation max 25° any direction
1080 - 1450 mm
2060 - 2110 mm
3080 mm
970 mm 1500 mm 610 mm
3040 - 3100 mm
2630 - 2690 mm
252-305
700 mm
*) 760i only

11
755/760i Description of the loader
Tyres Tread
pattern
Code Pressure Machine
width
Fits with fenders
Front Rear
Fits with snow
chains
27x8.50-15 TR 65414 2,5 bar 1080 mm - - -
26x12.00-12 GR 65212 2,0 bar 1350 mm x x 64973
26x12.00-12 TR 65739 2,0 bar 1350 mm x x 64973
320/60-12 TR 65224 2,0 bar 1350 mm x x 65603
320/55-15 GR 65459 2,0 bar 1360 mm x x 65722
320/55-15 TR 65506 2,0 bar 1360 mm x x 65722
400/50-15 *) GR 66257 2,0 bar 1420 mm x x -
400/50-15 *) TR 65958 2,0 bar 1450 mm x x -
Fuel requirements
Fuel: Ultra low sulfur diesel fuel only (sulfur content less than 15 ppm / 0,0015%).
Use only fuel that complies with any of the following:
- EN 590, DlN 51628 - Military NATO fuel F-54 (S = 10 ppm)
- No 1 Diesel - ASTM D 975-09 B-Grade 1-D S 15
- No 2 Diesel - ASTM D 975-09 B-Grade 2-D S 15
- ARCTIC (EN 590/ASTM D 975-09 B) for ambient temperatures below -10°C (14°F).
Biodiesel with max 10% bio content that complies with the standards above can be used.
Never add petroleum or any additive that does not comply with the above listed standards.
Engine oil requirements
Use only engine oil recommended by the engine manufacturer. The Kohler diesel engine with common rail high pressure
fuel injection requires high quality engine oil in order to work properly. See also Kohler Operators Manual.
Tyres
The loader can be equipped with different type of tyres for different operating conditions. Grass pattern (GR) tyres will
damage the ground surface less than tractor (TR) tyres, but provide less traction.
For the best stability and controllability, always use the largest tyres possible. Tyres that are narrower than the standard
tyres are intended for special purposes only with width restriction on the machine. Use only tyres and rims that meet
the original specifications and dimensions to avoid potential issues with load capacity, tyre size, or bearing load on
drive motors. Consult your dealer if further information is needed. Special tyres, such as studded wheels may also be
available. Consult your dealer for further information.
Emission control information
Avant 755 and 760i with Kohler KDI engine meets the most
stringent European 97/68/EC Stage 3B and US EPA and CARB
Tier 4 Final emissions standards for compression ignited engines
in 37-56 kW power category. Periodic maintenance must be
performed according to engine manufacturer’s specifications
in order to maintain emissions compliance. Emissions related
systems and required maintenance are shown in the owner’s
manual of the engine. It is the responsibility of the owner of the
loader to maintain it in good condition and to operate it with
correct type of fuel and other fuids.
Auxiliary hydraulics oil flow
Max. auxiliary hydraulics oil flow can not be used with all
attachments. Check correct engine rpm and auxiliary hydraulics
pump configuration for the attachment with the help of this
graph and the Operators Manual of the attachment.
1 pump
2 pumps
rpm
l/min
*) 760i only

12
755/760i
Load diagram
The lifting capacity of the loader is limited by the possibility of tipping around the front axle. The diagram below shows
the tipping loads and max. allowed loads in different loading situations on an even level surface with the loader chassis
in maximum articulation.
The diagrams can be interpreted as follows:
• The diagrams show tipping load and max. load with the
load at different distances from the front axle of the
loader
• Example: If the center of gravity of the load is
750 mm in front of the front axle, max. load is about
1250 kg with a driver weighing 75 kg and with the 170
kg integrated rear weight mounted on the loader.
• NOTICE: If the driver leaves the machine, tipping and
max. loads are reduced respectively.
• Tipping load and max. load depend both on the weight
of the driver and the eventual extra weights mounted
on the loader.
• Please note that the diagrams are based on the machine
operating on a level, even and firm supporting ground.
Loads should be significantly reduced when operating
on gradients and/or on soft ground.
• The loader is equipped with a load sensor system,
which gives an audible warning signal and an indicator
lights up in the dashboard when tipping load is being
approached.
• Read the safety instructions regarding handling of heavier
loads. Calibration instructions of the load sensor system
can be found on page 32.
Description of the loader
Tipping load with the loader
In max. articulation
Rear weight 170 kg
Driver 75 kg
Distance from front axle mm
Rated operating capacity (ROC)
The loader In max. articulation
Rear weight 170 kg
Driver 75 kg
kg
Transporting instructions and tie down points
Mount the articulation frame lock, shown on page 28, on
the machine during transports. Lower the boom down and
take off battery disconnect switch. Remember to remove
the frame lock after transport!
Tie down points are located on the rear frame on the
sides, and on the front frame close to the boom. Optionally
available are the rear bumper and / or behind the rear
wheels installed tie down brackets (Art. A418746), in
which the straps and slings can be attached.
The loader cannot be towed. It is equipped with hydrostatic
transimission and a hydraulic parking brake which can be
released only when the engine is running and there is
enough pressure in the hydraulic system. In case there
is a technical failure and the engine cannot be started or
doesn’t start, the machine must be lifted e.g. with a forklift
truck and transported to service.
The loader can be lifted by mounting appropriate lifting
slings on the ROPS frame or on the cab LX/DLX. Before
lifting, the attachment and eventual extra weights must be
removed. Mount the frame lock on the machine. Make sure
that the lifting slings cannot move and that the machine
doesn’t swing during lifting. Follow the instructions given
in the operator’s manual of the lifting slings.
Lift a loader with ROPS frame with four straps or slings
approved for lifting and minimum 2 metres in length. Loop
the lifting straps around the four ROPS posts. To lift a
loader with cab LX or DLX, four appropriate lifting eyelets
must be mounted and hooks and chains are required.
Lifting kit A418706 includes all necessary parts to lift a
loader with ROPS frame and kit A417352 to lift a loader
with cab LX/DLX with detailed instructions included.
Lower the boom and mount the articulation frame lock as
shown on page 28. Remove heavy attachment and extra
counterweights before lifting. Never lift a loader with
persons riding the machine.
Eyelets on extra side counterweights are for
installing or removing the sideweight only.
Never attempt to lift the loader from the
counterweigths or use them as tie-down
points.

13
755/760i
Operating instructions
Operating instructions

14
755/760iOperating instructions
Operating controls
Following picture shows the location of operating controls. The location
and function of controls may be slightly different in different models, see
following pages.
Cab DLX: Some of the switches
are on the panel in the cab.
1. Steering wheel
2. Drive pedal, left: drive backward
3. Drive pedal, right: drive forward
5. Control lever of boom and bucket
6. Hand throttle lever
7. Auxiliary hydraulics control lever
8. Control lever of telescopic boom
9. Rear auxiliary hydraulics control
lever (optional extra)
10. Selection lever of the pumps for
auxiliary hydraulics
11. 12 V outlet (max 15 A).
Cab LX/DLX see page 16.
12. Dashboard, see page 16
13. Switches on the panel
Work light
(option)
Hydraulic quick
attachment
(option)
See page 24
Parking brake
switch
See page 18
Drive speed
range selection
switch
See page 18
Emergency
blinker
(option)
Windscreen
wiper and
washer
(Cab option)
Beacon
(option)
2
1
3
5
6
7
89
10
11
12
13

15
755/760i Operating instructions
Control of loader boom, auxiliary hydraulics and other functions
Most of the functions of the loader are controlled at the control panel on the right side of the operator: Boom and bucket
movements, auxiliary hydraulics (attachments), engine revs etc. , depending on loader model. Following pictures show the
different functions: Attachment control
switch pack (option)
• Optional extra with which
electric functions of the
attachment are controlled
• Consists of 3 pcs control
switches, wiring and a 7-pole
socket which mounts on the
auxiliary hydraulics multi
connector (see page 8). The
corresponding socket of the
attachment electric wire is
mounted on the attachment
multi connector. This way
both the electric wire and
the hydraulic hoses of the
attachments are connected
at the same time with the
multi connector.
• Read the operator’s manual
of the attachment to see how
the switches are used with
each attachment.
5. Control lever of boom and bucket
(Functions of the electric joystick are explained on page 19)
• Pull backward to lift the boom
• Push forward to lower the boom
• Push left to raise the tip of the bucket (filling)
• Push right to lower the tip of the bucket (emptying)
6. Hand throttle lever
• Push forward to increase engine revs
• Pull backward to reduce engine revs
7. Control lever of auxiliary hydraulics
(hydraulically operated attachments)
• Push forward carefully to test the operating direction
of the attachment
• For continuous operation of rotating atatchments,
push forward & turn right to locking position
• Pull backward to operate the attachment in reversed
direction
• When using the electric joystick, this lever will
also move. Either way can be used to control the
attachment as needed.
8. Control lever of telescopic boom
• Push forward to extend the boom
• Pull backward to retract the boom
9. Control lever of rear or extra front auxiliary
hydraulics outlet (optional extra)
• Operates in similar way as the lever no 7.
• See page 20 for further instructions
10. Selection lever of the pumps for auxiliary
hydraulics
• Lever in front position (1-pump): one pump
coupled for auxiliary hydraulics (lower oil flow).
Use this setting unless higher hydraulic flow to the
attachment is required.
• Lever in back position (2-pump): two pumps
coupled for auxiliary hydraulics
5
6
7
8
9
10

16
755/760i
Dashboard
On the dashoard on the right side of the driver’s
seat are mounted gauges, indicators and switches
which help the operator to control the loader.
Operating instructions
21
23
410
19
20
18
16
15
13
11 12
Indicator lights
14
22
23 24
25
Ref. Symbol Indicator Colour Remarks
1Head-
lights Green Road traffic light kit, optional
2
Hydraulic
oil cooler
fan fuse
Red
See page 34
3
Load
sensor Red
Too heavy load is being lifted. See
page 5 and 32 for load sensor, and
page 12 operating capacity.
4
Work
lights Green
Standard front lights on
5Boom
floating Yellow Boom floating on. See 19
6Seat
heater on Green
Seat heater switch on the optional
air suspension seat (cab DLX only) is
located on the back side of the back
rest on the left, see page 17.
7
Malfunction
Indicator
Light
Red
The ECU has detected a fault
requiring immediate service and the
engine is set to fault mode (including
reduction of engine output). If
necessary, the loader can be driven
to a safe location, but must not be
loaded or used more than absolutely
necessary.
8
Coolant
tempera-
ture high
Red
High coolant temperature, remove
engine load or shut down the engine
and allow to cool. If repeated, find
cause for high temperature.
9
Check air
filter Orange
Air intake pressure loss more than
52 mbar. Clean or replace engine air
filter.
10
Grid
heater on Orange
Indicates that an electric heating
element at the engine intake is on.
The heater will be activated by
ECU when starting the engine at
very cold ambient temperatures.
Operation of heater can’t be
controlled by the operator of the
loader.
11 Check
Engine Yellow
The ECU has detected a fault and
a diagnostics code is stored in the
memory. See page 33.
12
Oil
Pressure
Low
Red
Shut down the engine immediately.
Low oil pressure can cause severe
engine damage. Check first if low
pressure is caused by low engine oil
level.
13 Water in
fuel Yellow
Water has been detected in fuel.
Drive to a safe location and drain
the water separator. See Page 33 for
further information.
1
56
789
17
22
23
25
24
19
20
15 16 17 18
10
9
8
7
3
2
14
5
6
11
12
14
13
Cab LX /DLX
ROPS

17
755/760i
Gauges and switches on the dashboard
Ref
14 Charge indicator
15 Drive release valve switch
16 Front light switch
17 Boom floating switch
18 Seat heater switch
19 Ignition switch
20 Signal horn
21 12 V outlet (max 15 A) in cab LX/DLX, for others see
page 14.
22 Hour meter
23 Tachometer
24 Thermometer
25 Fuel level gauge
Operating instructions
Controls in the footwell
Following picture shows the controls located in the footwell
2
1
1. Drive pedal, left: drive backward
2. Drive pedal, right: drive forward
See correct operation of the drive pedals on page 22.
Suspension seat
The suspension seat is equipped with a seat belt and has
the following adjustments:
1. Suspension adjustment
• by turning the knob counterclockwise suspension
gets harder, by turning it clockwise the suspension
gets softer
2. Angle of the back rest
• the angle of the back rest can be adjusted by pulling
the lever
3. Seat position
• the distance of the seat from the steering wheel can
be adjusted with the lever which is located u n d e r
the front edge of the seat
4. Arm rest angle adjustment
• The angle of the arm rest can be adjusted by turning
the roller under the arm rest
Air suspension seat (option for cab DLX)
To adjust the air suspension seat, sit
on the seat and switch the ignition
switch to “ON”. Check the indicator
on front of the seat. Pull the handle up
or push it down, so that the indicator
points the marker in the middle.
The seat is equipped with heater.
Heater switch is located of the back
rest on the left. Below it is located
the lumbar support adjustment.
NOTICE: If the loader is equipped
with the air suspension seat, the seat
heater switch and indicator light on
the dashboard are disabled
2
1
3
4
Seat belt and seat adjustments
Always use seat belt while driving. Make sure that the
seat is properly adjusted to keep vibrations transmitted
by the seat at minimum. Long term exposure to vibrations
may cause health effects. Also, as far as possible, keep the
operating terrain in good condition to minimize vibrations

18
755/760i
Drive speed range selection switch
Avant 760i is equipped with two-speed hydraulic drive
motors. Drive speed range can be selected with the switch
on the control panel right (see page 14). In addition to
speed, the speed range switch affects the pulling force as
shown in table.
Higher speed range is intended for longer travels where
high pulling force is not necessary.
Do not change the drive speed range while
driving with a higher speed. Always stop the
machine first or slow down the speed before
switching on higher or lower speed. Be careful
when driving at higher speed range. Do not
turn the steering wheel quickly at high travel
speed.
Parking brake switch
The loader is equipped with a hydraulic parking brake. It
locks the front wheels. Parking brake is operated with the
switch on the control panel right (see page 14). On cab
LX/DLX the switch is located in the panel up right.
• A red indicator on the switch lights up
when parking brake is engaged.
• The green backlight under the “P” is lit all
the time.
Parking brake engages automatically when the engine is
stopped. The brake can be released only when the engine
is running and there is hydraulic pressure in the system.
Do not engage the parking brake when the
machine is moving unless in emergency. Using
the brake while moving may cause the locking
of front wheels and sudden stopping of the
machine.
If the parking brake is engaged repeatedly
when the machine is moving the brake plates
in the front drive motors will get worn quickly.
Always stop the machine before engaging the
brake.
Seat heater
The suspension seat is equipped
with an electric seat heater. Seat
heater switch (18) and indicator
are located on the dashboard.
Battery disconnect switch
The loader is equipped with a
battery disconnect switch. The
switch is located in the rear of the
machine, on the right side (see
picture). Battery disconnect
switch cuts the current between battery and the rest of
the electric system. Always switch off main current when
the loader is not used for a longer period of time in order
that the battery doesn’t get empty, or when servicing the
machine.
Telescopic boom
Telescopic boom is operated with
the control lever no. 8 on the
control panel (see page 15) or with
the rocker switch on the joystick
(see page 19). Length of the
telescope is 700 mm and additional
lifting height is 410 mm.
Smooth drive (option)
Avant 760i can be equipped, as
an option, with the smooth drive
which is a shock absorber system
for the boom. When driving at high
speed with a heavy load or heavy
attachment, the boom starts to
move up and down, making driving
unpleasant. The smooth drive
consists of an accumulator which absorbs and eliminates
boom movements and makes driving considerably
smoother and more stable. Smooth drive is switched on
with the boom floating switch no. 17.
NOTICE: The machine must also be equipped with both
boom self levelling and boom floating.
Switch on the smooth drive only when
stationary and when the load is close to the
ground to avoid change in stability caused
by possible movement of the boom when
switching on. Keep the smooth drive off when
loading or lifting with the loader.
Operating instructions
Speed range switch
Speed range with
standard tyres
0-15 km/h 0-30 km/h
Pulling force, forward 100% 50%
Pulling force, reverse 100% 25%

19
755/760i
Boom self levelling (option)
Self levelling system keeps the position
of the attachment the same in relation
to the ground, regardless of the position
of the boom.
Self levelling is hydraulic: there is a
levelling cylinder on the left side of the
boom which follows the movements of the bucket tilt
cylinder and keeps the attachment level. Self levelling is
disabled when the boom floating is switched on.
Boom floating (option)
The floating system releases the lift cylinder, so that the
boom floats upwards from the position where it is when
boom floating is switched on, allowing the attachment to
follow the contours of the terrain.
1. Lower the boom down
2. Switch on the floating with
rocker switch no.
3. Boom floating indicator
on the dashboard lights up
When boom floating is being used, it is
possible that air gets in the hydraulic system.
This can lead to inaccurate boom movements
and the boom can give in. Therefore the
boom and attachment coupling plate should
always be moved to extreme end positions
after switching off boom floating. Use boom
floating only when necessary.
Joystick
The loader is equipped with the
8 function joystick, where the
operation of auxiliary hydraulics
and telescopic boom is electric.
1. Auxiliary hydraulics
• push the buttons to engage
and disengage auxiliary
hydraulics.
2. Telescopic boom
• with the rocker switch the telescopic boom can be
operated steplessly (extension- retraction). Speed of
the telescoping function depends on the position of
the pump selection lever.
Engine block heater (option)
The loader can be equipped, as an option, with an engine
block heater. Engine block heater outlet (220V-240V )is
on the right side in the rear of the machine.
Trailer coupling (option)
The loader can be equipped, as
an option, with a trailer coupling.
There are two types available: a
50 mm ball hitch and a 50 mm ball
hitch with towing pin. Both can
be mounted either directly on the
rear bumper or on the extra back
weight.
Max. allowed vertical load of the
trailer coupling is 6900 N, max.
towing load is 6000 N.
Make sure that the weight on the trailer is distributed
correctly so that the trailer cannot cause an upward lifting
force on the trailer coupling
Extra counterweights
(option)
The loader can be equipped with
extra counterweights that are
mounted on the rear bumper.
Max. amount of extra weights
(29 kg/pcs) is 3 pcs. If the machine
is fitted with an extra weight with
trailer coupling, max. amount of
extra weights is 1 pcs. The loader
can also be equipped with an extra
side weight kit (80 kg or 180 kg)
which mounts behind the rear
wheels.
Work light kit (option)
The loader can be equipped with
extra work lights, making it easier
to work in low light. The lights are
operated with the switch on the
control panel (see page 14).
Headlight, beacon, blinker & reflector kit
(option)
This optional equipment enables
road traffic registration in certain
countries. Requirements vary in
different countries, please consult
your local AVANT distributor.
17
Operating instructions
Extra back weight 29 kg
Rear side weight (2x40 kg)
Rear side weight (2x90 kg)

20
755/760iOperating instructions
Tilt adapter (option)
The hydraulic tilt adapter mounts
between the attachment and the
attachment coupling plate. It allows
the driver to tilt the attachment
sideways 12,5 degrees to both
directions from the driver’s seat.
Tilt adapter is intended mainly
for non-hydraulic attachments, but with the optional
double acting extra auxiliary hydraulics outlet in the front
(A35477) it is possible to mount a hydraulically operated
attachment (e.g. a 4 in 1 bucket) at the same time. Tilt
adapter is operated with the auxiliary hydraulics control
lever (no. 7, page 15).
Drive release valve
The switch no. 16, LOCK, controls
a valve, which is used to divert the
oil flow between left and right side
hydraulic motors, and this affects
the pulling force.
LOCK OFF: In this mode, the hydraulic oil flows in series
from motor to motor. The wheels will roll more freely and
the loader leaves less tire marks on soft surfaces.
LOCK ON: In this mode the hydraulic oil flows in parallel
between the hydraulic motors in each side, similar to a
differential lock in operation. This improves the towing
capability of the loader.
Anti slip valve (option)
The valve positively diverts oil flow
between the right and left side
hydraulic motors and improves
traction on slippery and uneven
surfaces. It is engaged by pressing
continuously on the switch on the
joystick. As soon as the switch is
released, anti slip valve is released.
The function of the anti slip valve depends also on the
position of the drive circuit release switch no. 15:
LOCK ON : Anti slip valve diverts oil flow between all
four hydraulic motors - all four wheels have best possible
traction. Use sufficient engine revs and press properly on
the drive pedal.
LOCK OFF: Drive circuit released – anti slip valve diverts
the oil flow between the front left and right hydraulic
motor only, not the rear hydraulic motors.
Extra auxiliary hydraulics outlets, front
and rear (option)
In addition to the standard auxiliary hydraulics outlet,
the loader can be equipped with a double acting extra
outlet. The extra hydraulic outlet can be fitted either to
the front of the loader or to the rear, and the couplers
are conventional type quick couplers. The installed extra
outlet is controlled with the lever no. 9 (see page 15).
The loader can be equipped with either the rear hydraulics
outlet or with the extra front outlet – but not with both.
1. Extra auxiliary hydraulics
in the front
• Quick couplers are located
under the multi connector
2. Quick couplers in the rear
• Quick couplers are
located on top of the
radiator.
Double acting outlet
Warning beacon (option)
The beacon can be removed
quickly by unturning its retaining
screw and then by pulling the
beacon out. Place the protective
seal on the beacon stand to prevent
water entering and damaging the
connectors. Handle beacon with
care. The beacon is sealed and
its inner components cannot be
replaced or repaired by user.
Beacon includes high-voltage components.
Do not use or repair damaged beacon,
replace with new one.
Light bar (option)
Flashing lights on the light bar, only
available on DLX cab.
pressure 1 pressure 2
pressure 1 pressure 2
tank line