Avantco 177HWDA2 User manual

User Manual
1 www.AvantcoEquipment.com
Hot Water Dispenser
Models: 177HWDA2
Please read and keep these instructions. Indoor use only.
12/2022

User Manual
2 www.AvantcoEquipment.com
Safety Information
WARNING: Failure to comply with all requirements in this manual may lead to safety hazards and void warranty.
• This appliance is designed for COMMERCIAL USE ONLY.
• DO NOT use outdoors.
• DO NOT alter or deform the power cord or plug in any way. This may cause electrical shock and/or
damage unit.
• Cleaning & maintenance should only be performed by properly trained persons with supervision.
• Children should be supervised to ensure that they do not play with the appliance.
CAUTION:
• ALWAYS place appliance on stable surface in a fully vertical position.
• ALWAYS unplug unit from power supply before cleaning or servicing.
• ALWAYS use caution when touching unit, surfaces are hot and can cause burns.
NOTICE:
• ALWAYS use on a circuit that is properly protected and capable of the rated load.
• Electronically ground the chassis.
• DO NOT use an extension cord.
5021062 5021062

User Manual
3 www.AvantcoEquipment.com
Installation
NOTE: Please use filtered and softened water. If using ground or tap water, please soften it first. Unsoftened water will
decompose dissolvable minerals and turn into limescale after boiling. The limescale will reduce the machine's
thermal efficiency and lifetime.
1. Carefully unpack the hot water dispenser and check for damage and missing parts.
2. Place hot water dispenser on sturdy, level, heat-resistant, non-flammable surface near power supply and water
supply. Do not connect water line or power cord at this time.
3. Attach the water line to the inlet located on the rear of the dispenser. Hold the water inlet fitting with a wrench when
tightening the water line.
4. Turn on the water supply. Make sure to check for leaks at the water inlet. Tighten fitting if necessary.
5. Connect power supply cord into proper power supply as indicated on the nameplate of the machine. Make sure the
machine is switched OFF before connecting to the power supply.
CHECK BEFORE STARTING:
1. The power cord should be connected to a 110/120V outlet.
2. The water line should be connected and not leaking.
3. The dispenser should be installed on a level, stable surface.
Recommended Accessories
Item Number Description
790OCLOKITLG C Pure Oceanloch-L Water Filtration System & Pressure Gauge
147LIMEBGONE1G Lime B Gone, Noble Delimer/Descaler
A. Tray
B. Drain Outlet
C. Water Inlet
D. Inlet Pipe
E. Water Faucet
F. 110 -120V
AB
CD
E
F

User Manual
4 www.AvantcoEquipment.com
Operation Instructions
1. Plug in the machine to the power supply.
2. Verify that the water supply is on and lightly press the ON/OFF Button (A) to turn the unit on.
3. The unit will automatically start filling and heating water. The "Heating" indicator light (B) will be on during this step.
4. Once the water reaches the appropriate temperature, the unit will be in "Keep warm" status (C).
5. When the unit is ready, place an empty cup or container directly under the faucet and pull the handle towards you.
When finished, release the handle.
6. When the water level becomes low, the unit will fill and heat water. The heating indicator light (B) will once again be
on during this step.
ON/OFF HEATING KEEP WARM
C
A
B
ONLY power up the boiler when the thermostat is in the OFF position.
DO NOT power up the boiler when water supply is off.

User Manual
5 www.AvantcoEquipment.com
Daily Cleaning and Maintenance
Cleaning should be done at the end of every workday. Only those persons trained and qualified in equipment repair
should attempt to clean the inside of this dispenser.
1. Turn the unit OFF, unplug, and allow unit to completely cool before cleaning.
2. Use a clean cloth with hot water mixed with Noble Chemical Sunbright liquid dish soap (or a neutral soap) to clean
the outside of the unit.
3. For dirt smudges on the unit's exterior, a damp cloth will suffice.
NOTE: Deliming should be performed at least once every six months by an authorized technician. Customers in
areas with hard water will need to perform this procedure more frequently.
Unit Specifications
Model 177HWDA2
Voltage 110-120 V
Frequency 60Hz
Wattage 1500W
Capacity 2 Gallons
Output 5 Gal/Hour
Water Input Pressure 10-58 psi
Water Connection ¼"
Dimensions 7 1/10"x 14 9/10"x 22 9/10"
DO NOT use harsh chemicals or abrasive materials.
DO NOT submerge or saturate with water, unit is not waterproof.