Avante HI-LO CHAIR User manual

HI-LO CHAIR ADJUSTABLE BED
MANUAL

TABLE OF CONTENTS
Safety ………...……………………………….….….… 1
Introduction ………………...………………..………. 3
Care ……………………………………………...... 4
Features ...…………..………………..………..…….....5
Unpacking Your Base ………………………….….......7
Attaching Legs …………………....………...…………8
Attaching Side Rails …………………………………...9
Attaching Headboard …………………………...……10
Hand Control Overview ………….....….……………11
Troubleshooting ..……………………………..……..12
Product Guarantee ………..………………….....……13
Notes …………………………………………………..14

SAFETY
ATTENTION: Important Safety Disclaimers
Read all instructions before using
your adjustable base. Save these instructions.
WARNING
Always unplug the base from electrical outlet before servicing any part of
the base. Unplug the base before cleaning. To safely disconnect, ensure
base is in a flat position with all motors off.
TO REDUCE THE RISK OF SHOCK, FIRE OR INJURY: For optimal safety and
operation, plug the bed base into a surge protector (not included). Ensure to always
unplug the base from the electrical outlet before servicing or cleaning any part of the
base. Keep the power cord away from heated surfaces. Discontinue use of the bed base
and contact a qualified service centre if it has a damaged cord or plug, if it is not
working properly, or it has been dropped into water. Only use this bed base for its
intended use as described in this manual. Do not use accessories/attachments that are
not recommended by the manufacturer. Improper connection of the equipment can
result in the risk of electrical shock, electrical fire or fault if the plug does not fit your
outlet. Contact a qualified electrician to install a suitable outlet.
ENTRAPMENT WARNING: During the operation of the bed, gaps are created. A
child, person’s limb or pets can be entrapped during use and when base is in raised
position. Always keep gap areas clear and keep limbs on top of the base. Failure to
follow this warning could result in serious injury or death.
PETS AND CHILDREN: Dispose of all packing materials immediately after opening
as it may pose a risk to small children and pets. To avoid injury, it is not advised to
allow children and small pets to play under the bed. Children should not operate the bed
base without adult supervision.
PACE MAKER WARNING: This product produces a vibration sensation. It is
possible an individual with pacemakers may experience a sensation similar to exercise.
Consult your physician for information as to how this may affect you.
Page 1

SAFETY
• To reduce the risk of falls on height adjustable bases, the base should
always be in its lowest position for sleeping and resting. The highest
position should only be used for carer’s access to the user, ease of
entry and exit of bed for the user and ease of making the bed.
• A minimum of 2 able and fit adults should be present when lifting or
moving the bed. It is recommended to use trolleys or other lifting/
moving devices where possible.
• Careless use of naked flames, cigarettes or other heat sources could set
fire to this product.
• Do not operate whilst any person is under the base whilst raising/
lowering or adjusting the bed.
• Care should be taken that no body parts are in or near the adjustable
frame while operating.
• Ensure the cabling of the bed is free from the mechanism.
• Don’t run over electrical cables when moving the bed.
• Do not manipulate or conduct electrical maintenance on the motors or
any of the beds electrical components or cables. Any electrical work
must be facilitated by a qualified tradesperson.
WARNING
• Stay clear of moving parts while in motion.
• Before adjusting, make sure children and pets are clear of moving
parts and are not under bed base.
• Do not allow children to operate bed base without adult supervision.
Page 2

INTRODUCTION
Congratulations on the purchase of your new
AVANTE HI-LO CHAIR ADJUSTABLE BED
The Hi-Lo Chair bed has been expertly designed to make getting into and
out of bed easier. With vibration massage motors and Cool Balance
mattress this product is a revolutionary leap forward in intelligent design.
Key Features:
• Hi-Lo Lift Function
• Easy-Up Functionality
• Head and Foot Adjustability
• Attached Side Grab Rails
• Cool Gel Infused Mattress
• Vibration Massage Functions
• Wired Hand Control which is Backlit
• 200kg Weight Rated
Page 3

CARE
GENERAL CARE INSTRUCTIONS
• Legs and castors should be checked for tightness regularly.
• When transporting - do not over tighten when restraining.
• Do not exceed the maximum weight limit for this bed
(200kg total).
• Do not jump on or abuse the bed.
• Do not constantly push the buttons on the controller when
not for intended use.
• Use the controller only for adjusting the bed frame for
intended use - not for entertainment.
• Lubricate moving parts using a non-corrosive lubricant every
6 months or as required. Avante recommends the use of
INOX.
• Beds should be positioned with clearance from walls and
objects so as not to cause damage.
• Do not rock or tilt the frame.
Page 4

FEATURES
PRODUCT FEATURES
• Stylish modern living design
• Adjustable head and foot parts
• Chair and lift position to assist
getting on and off bed
• Head and foot massage function
• Wired remote control with LED
backlighting
• Fixed side grab rails for extra
support
• Includes cool gel infused
mattress
FRAME DESIGN FEATURES
• Low voltage, DC lift system
provides smooth and efficient
operation
• Long lasting steel support
• Superior steel foundation
• Powder coated steel
• Designed to lift up to 200kg total
weight
• Gravity fall motors
• Wall aligned technology.
Page 5

UNPACKING YOUR BASE
1. Open both boxes (bed base and headboard) and remove protective
plastic.
Page 6

UNPACKING YOUR BASE
3. Locate box of parts and side rails, cutting the zip ties and removing the
protective plastic.
Page 7
4. Locate hand controller, cutting the zip tie and removing the protective
plastic.

ASSEMBLING -
ATTACHING LEGS
1. Flip the bed carefully on its side.
2. Locate box of legs and screw in to each corner of the bed base.
3. Once completed, flip bed carefully back to a flat position.
Page 8

ASSEMBLING -
SIDE RAILS
Page 9
2. Push the two prongs
into the holes, pushing
against the mattress as
shown.
1. With the bed in an
upright position, locate
the side rails and line
up with holes as
shown.
3. Locate the bolt as
shown and fasten until as
tight as possible.

ASSEMBLING -
ATTACHING THE HEADBOARD
Page 10
1. Locate bracket slot at the
bottom of the headboard.
2. Find the same matching bracket
slot at the top of the bed base.
3. Slide the headboard brackets into
the top of the bed base to
secure the headboard.

HAND CONTROL OVERVIEW
Ensure the remote is plugged into the control box
underneath the bed. The remote should look like
the one to the right.
Please refer to the following diagram explaining
the functions.
Raise head
part of the bed
Lower head part
of the bed
Raise leg part
of the bed
Lower leg part
of the bed
Form lift chair
position then
lift up
Bed return to
flat position
Raise Bed
Height
Lower Bed
Height
Page 11
Turn the
head massage
on and off
Turn the foot
massage on
and off
Hand Control Calibration
When first connecting your chair bed to power, you will need to continuously press the
lift chair down button to calibrate the control box. The bed’s foot part will raise up
then go down. Once completed, the bed will be ready to use. The re-calibration is
required in the event of power black out, or power has been turned off to the bed.

TROUBLESHOOTING
Below is a list of possible problems & their solutions should the
adjustable base fail to operate properly
PROBLEM SOLUTION
The base does not respond when the
remote is used.
Remote LED illuminates and appears
to be normal.
Perform any or all of the following:
• Check that the power cord is plugged into a
working & grounded electrical outlet.
• Check that the light on the transformer is on.
• Check the home’s circuit breaker & fuses.
• Unplug the power cord from the outlet. After
one minute, plug it back in. Press chair down
button.
The remote does not work
or does not light up.
• Check the remote LED light is lighting up
when pressed. If not, please check that the
power cord is plugged into a working &
grounded electrical outlet.
Base stutters while in motion. • Clear any clutter or obstructions under and
around the adjustable base.
• Ensure the buttons on the remote are being
pressed firmly down when operating the Head
& Foot functions.
If you have followed the instructions outlined in this manual, and your problem
is persisting, please contact the retailer you originally purchased your bed from
or Avante Australia for further assistance.
Page 12

PRODUCT GUARANTEE
Congratulations on your purchase. Avante Australia is an
International Brand that uses technology, production facilities and
teams with over 20 years’ experience.
Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for
a major failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality and the failure does not amount
to a major failure.
Avante Australia proudly provides a full guarantee (10 years—applies to
frame, structure & electric motors only. All other electronic components &
upholstery are covered for 2 years). Please refer to www.avante.com.au for
details against faulty workmanship and/or faulty materials. During the
guarantee period, if we are satisfied there is a genuine fault, we will repair
or replace the product if it’s an option.
THE GUARANTEE DOES NOT EXTEND TO THE FOLLOWING:
• Fabric (including stains, soiling, burns and normal wear).
• Items upon inspection that are deemed unsanitary.
• Normal wear and tear, or damage caused by abuse.
• Clearance bedding sold in ‘as is’ condition.
• Failure to comply with manufacturer care and maintenance
instructions.
IN ORDER FOR THIS GUARANTEE TO BE VALID YOU MUST:
• Be the original purchaser.
• Provide a copy of the original store receipt.
• Not misuse the product (refer to care and maintenance and safety
sections).
Page 13

PRODUCT GUARANTEE
PLEASE TAKE CARE OF YOUR HI-LO CHAIR BED BY TAKING
THE FOLLOWING PRECAUTIONS:
• Legs and castors should be checked for tightness regularly.
• When transporting - do not over tighten when restraining.
• Maximum recommended weight limits; on a High Low Lift bed
200kg.
• Do not jump on or abuse the bed.
• Do not constantly push the buttons on the controller when not for
intended use.
• Use the controller only for adjusting the bed frame for intended use -
not for entertainment.
• Lubricate moving parts using a non-corrosive lubricant every 6
months or as required. Avante recommends the use of INOX.
• Beds should be positioned with clearance from walls and other objects
so as not to cause damage.
We will not cover damage caused by neglect, mistreatment or general wear and
tear of the bed. Regular maintenance is required.
MAKING A CLAIM
To make a claim under this Guarantee please contact your bedding retailer
who will initiate the claim process with us. If this cannot be done, please
contact Avante Australia Pty Ltd directly via the details on the back of this
manual.
Avante Australia will require photos of Mattress and Base support system
to be sent at the time of a claim being made. For details of how to take
acceptable photos please contact Avante Australia (contact details on back
page).
Page 14

NOTES
Page 15

NOTES
Page 16

Avante Australia Pty Ltd
Unit 2, 29-71 Saltwater Circuit
Narangba, QLD 4504
Phone: [phone]
Fax: [phone]
www.avante.com.au