Avante LUXURYFLEX User manual

LUXURYFLEX
ADJUSTABLE BED MANUAL

TABLE OF CONTENTS
Safety ………...………………………………….….…1
Care ………………………...……………… ………...3
Features...…………..………………..……….…….....4
Unpacking Your Base ………………….….…...........5
Attaching Legs & Retainer Bar to the Base …………6
Hand Control Overview………………….….…........7
Reprogramming Hand Control Positions..………….8
Syncing Long Single Base’s ...…………..…….……..9
Troubleshooting ..……………………………..……..10
Product Guarantee ………..…………………....…...12

SAFETY
ATTENTION: Important Safety Disclaimers
Read all instructions before using your adjustable base. Save these
instructions
WARNING
Always unplug the base from electrical outlet before servicing any
part of the base. unplug the base before cleaning. To safely dis-
connect, ensure base is in a flat position with all motors off.
TO REDUCE THE RISK OF SHOCK, FIRE OR INJURY: For optimal safety
and operation, plug the bed base into a surge protector (not included). Ensure to
always unplug the base from electrical outlet before servicing or cleaning any part
of the base. Keep the power cord away from heated surfaces. Discontinue use of
the bed base and contact a qualified service centre if it has a damaged cord or
plug, it is not working properly, or it has been dropped into water. Only use this
bed base for its intended use as described in this manual. Do not use accessories/
attachments that are not recommended by the manufacturer. Improper connec-
tion of the equipment can result in the risk of electrical shock, electrical fire or
faulty If the plug does not fit your outlet, contact a qualified electrician to install
a suitable outlet.
PETS AND CHILDREN: Dispose of all packing materials immediately after
opening as it may pose risk to small children and pets. To avoid injury, it is not
advised to allow children and small pets to play under the bed. Children should
not operate the bed base without adult supervision.
1.

NOTES:
SAFETY
·To reduce the risk of falls on height adjustable bases, the base should always
be in its lowest position for sleeping and resting. The high position should
only be used for carer’s access to the user, ease of entry and exit of bed for
the user and ease of making the bed.
·A minimum of 2 able and fit adults should be used when lifting or moving
the beds. It is recommended to use trolleys or other lifting/moving devices
where possible
·Careless use of naked flames, cigarettes or other heat sources could set fire
to this product
·Do not operate whilst any person is under the base whilst raising/lowering
or adjusting the bed
·Care should be taken that no body parts are in or near the adjustable frame
while operating
·Ensure the cabling of the bed is free from the mechanism
·Don’t run over electrical cables when moving the bed
·Do not manipulate or conduct electrical maintenance on the motors or any
of the beds electrical components or cables—Any electrical work must be
facilitated by a qualified tradesperson
WARNING
- Stay clear of moving parts while in motion.
- Before adjusting, make sure children and pets are clear of moving
parts and are not under bed base.
- Do not allow children to operate bed base without adult supervision
2

CARE
GENERAL CARE INSTRUCTIONS
·Legs and castors should be checked for tightness regularly
·When transporting - Do not over tighten when restraining
·Do not exceed the maximum weight limit for this bed
·Always lock castors other than when moving or relocating the bed
·Do not jump on or abuse the bed
·Do not constantly push the buttons on the controller when not for in-
tended use
·Use the controller only for adjusting the bed frame for intended use -
not for entertainment
·Lubricate moving parts using a non-corrosive lubricant every 6
months or as required. We recommend the use of INOX
·Beds should be positioned with clearance from walls and objects so as
not to cause damage
·Do not rock or tilt the frame
3.

FEATURES
4.
·Stylish Modern Living Design
·USB Port
·Underbed Lighting
·Zero Gravity
·Wireless remote control with LED
screen
·Chrome legs
·Battery back up
·Dual zone massage
·3 speed massage unit
FRAME DESIGN FEATURES
·Whisper quiet, low voltage, DC lift
system provides smooth and efficient
operation.
·Long lasting steel support
·Superior steel foundation
·Rust proof and powder coated steel
·Designs available for lifting up to
250kg
·Gravity fall motors
·Can suit any adjustable bed mattress
·Wall aligned technology

UNPACKING YOUR BASE
5.
1. Open the Carton box & remove the protective plastic
2. Open all the parts boxes & cut the zip ties to release all parts

ATTACHING LEGS & RETAINER
BAR TO THE BASE
6.
1. Locate the box containing the bed legs
2. Simply screw in the 4 corner legs as shown with included leg bolts
3. Flip over the base & insert the head & foot retainer bars as shown
below

HAND CONTROL OVERVIEW
7.
To turn on hand control, insert the 3* AAA
batteries into the back of the controller
Turn head vibration on/off
Head & foot both raised 15º
Head & foot both flat
Head raised 10º—Foot raised 30º
Head up or down
Foot up or down
Head raised 60º—Foot raised 20º
Underbed lighting on/off
Turn foot vibration on/off
Change vibration intensity

REPROGRAMMING HAND
CONTROL POSTITIONS
8.
The latest version of the Avanté Australia Luxuryflex now features memory po-
sition function as standard.
If you wish to change the pre-set positions included on your reprogrammable
remote, simply put the bed in the desired position and push and hold one of the
pre-set position buttons (“Zero Gravity”, “TV/PC” or “Lounge”) along with
the “Flat” button at exactly the same time for 3 - 5 seconds. Once you hear a
beep, the current position of the bed is now saved as a custom position under
the button you chose to push and hold.
For example:
If the pre-set Lounge position is not ide-
al, and you would prefer it to raise the
head further and put the foot of the bed
slightly lower, simply put the bed into
your ideal “Lounge” position by using
the head and foot up and down buttons.
Once the bed is in the position you wish
to save, then push and hold the
“Lounge” & “Flat” buttons for 3 – 5
seconds. You have now set a custom po-
sition under the “Lounge” button.
Follow the same process for each of the
pre-set positions to create the ideal posi-
tions for your body shape. Each of the
pre-set positions can be customized to
suit your needs. The entire unit can be
reset to factory pre-set positions by un-
plugging the unit for more than 5 hours.

SYNCING LONG SINGLE
BASE’S
9.
1—Fit Batteries to the hand control
2—Connect power to the transformer
3—Press & hold the head & foot ‘up’ buttons (as pictures below) at the
exact same time & wait up to 20 seconds until you hear a beep or the
screen changes
4—Once you hear a beep and the screen changes, your hand control is
then paired. If no beep or screen change, repeat previous step & ensure
you disconnect the power for 5 minutes in between attempts

TROUBLESHOOTING
10.
Below are a list of possible symptoms & their solutions should the
adjustable base fail to operate properly
SYMPTOMS SOLUTIONS
The base does not respond when
the remote is used. Remote LEF
illuminates and appears to be nor-
mal
Perform any or all of the following:
* Check that the power cord is plugged in-
to a working & grounded electrical outlet
* Check that the light on the transformer
is on
* Check the home’s circuit breaker and
fuses
* Unplug the power cord from the outlet.
After one minute, plug it back in . Press
any button on the remote
The remote does not work or light
up
* Check the remote LED light is lighting
up when pressed. If not, please replace
3*1.5V AAA batteries
Base stutters while in motion * Clear any clutter or obstructions under
& around the adjustable base. Radio fre-
quency interference from other remotes or
electronic devises may affect normal opera-
tion.
* Check batteries in remote
* Assure the keys on remote are being
pressed firmly down then operating the
Head & Foot buttons

Massage motor/s seem exces-
sively loud during operation
* Hard surface flooring may cause added vi-
bration. Place carpet pieces or rubber furniture
cups under each leg or caster of the bed.
* Check that the bed is not in direct contact
with a wall, or other object that may cause vi-
bration or noise.
* If adjustable base is installed on top of a bed
frame, check that the massage motors are not
causing the bed frame (or components) to vi-
brate or rattle
* If a headboard is utilized, please check that
the attachment hardware is tightened firmly
TROUBLESHOOTING
11.

PRODUCT GUARANTEE
12.
Congratulations on your purchase. Avanté Australia is an International Brand that
uses technology, production facilities and teams with over 20 years’ experience.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.
Avanté Australia proudly provides a full guarantee (at least 5 years on Frame
and Motor, 2 Years on Electronic Components, please refer to our website for
details) against faulty workmanship and/or faulty materials. During the guar-
antee period, if the company is satisfied there is a genuine fault, it will repair or
replace the product at its option. However, after the first 12 months, transporta-
tion costs will be met by the purchaser.
THE GUARANTEE DOES NOT EXTEND TO THE FOLLOWING:
- Fabric (including stains, soiling, burns and normal wear)
- Items upon inspection that are deemed unsanitary
- Normal wear and tear, or damage caused by abuse
- Clearance bedding sold in ‘as is’ condition
- Failure to comply with manufacturer care and maintenance instructions
IN ORDER FOR THIS GUARANTEE TO BE VALID YOU MUST:
- Be the original purchaser
- Provide a copy of the original store receipt
- Not misuse the product (refer to care and maintenance and safety sections)

MAINTENANCE INSTRUCTIONS
·Legs and castors should be checked for tightness regularly
·When transporting - Do not over tighten when restraining
·Maximum recommended weight limits; on a High Low Lift bed 180kg.
On a NON hi lo lift bed 125 kg per position on a double and queen with a
maximum load of 250kg. On a Long Single or King Single 1 person with
maximum load of 250 kg
·Always lock castors other than when moving or relocating the bed
·Do not jump on or abuse the bed
·Do not constantly push the buttons on the controller when not for intend-
ed use
·Use the controller only for adjusting the bed frame for intended use - not
for entertainment
·Lubricate moving parts using a non-corrosive lubricant every 6 months or
as required. We recommend the use of INOX
·Beds should be positioned with clearance from walls and objects so as not
to cause damage
MAKING A CLAIM
To make a claim under this Guarantee please contact your bedding retailer who
will initiate the claim process with us. If this cannot be done, please contact
Avanté Australia Pty Ltd directly via the details on the back of this manual.
Avanté Australia will require photos of Mattress and Base support system to be
sent at the time of a claim being made. For details of how to take acceptable
photos please contact Avanté Australia.
NOTES:
PRODUCT GUARANTEE
13.

Avanté Australia Pty Ltd
14 Huntington Street
CLONTARF QLD 4019
Phone: [phone]
Fax: [phone]
Web: www.avanteaustralia.com.au