Avanti WBV21DZ User manual

WINE CHILLER
Model Number: WBV21DZ
SERVICE MANUAL
CAUTION
Before servicing, make sure to unplug the appliance.
Replace all part before operating the appliance.
Failure to do so could result in death, electrical shock or personal injury.
Avanti Products, A Division of the mackle Co.,Inc INC.
P.O.Box 520604 – Miami, Florida 33152 USA
www.avantiproducts.com

2
TABLE OF CONTENTS
1. SPECIFICATIONS……………………………………………………………………3
2. NAME OF PARTS……………………………………………………………………4
3. REFRIGERANT CYCLE DIAGRAM……………………………………………….5
4. WIRING DIAGRAM…………………………………………………………………..6
5. COMPRESSOR ROOM VIEW AND PARTS LIST……………………………….7
6. HOW TO REMOVE THE SHELVES………………….……………………………8
7. HOW TO REPLACE THE BOTTOM GRILLE……………………………….…..8-9
8. HOW TO REMOVE THE DOOR….………………….…………………………..9-11
9. RELACING THE CONTROL PANEL……………………………………….....11-12
10. REPLACE THE MAIN PCB………………….…………………...…………..…13-14
11. REPLACE REAR AIR DUCT THE EVAPORATOR FAN MOTOR…………15-16
12. REPLACE THE LED LIGHT ASSEMBLY…………………………..………...16-17
13. REPLACE THE CONDENSER FAN MOTOR, COMPRESSOR STARTER&
PROTECTOR........................................................................................................18-19
14. REPLACE THE DOOR GASKE, CHARCOAL FILTRATION………………....20
15. TROUBLESHOOTING…………………………………………………………...21-22
16. EXPLOSION VIEW & PARTS LISTS……………………………….….……...23-25

3
1. SPECIFICATIONS
1.1 WBV21DZ
Model No. WBV21DZ
Type BUILT-IN OR RECESSED OR FREE STANDING
Capacity
No. of Wine Bottles 21
Capacity Zone One - L 75
Zone Two - L 75
Zone Three - L N.A
Performance & Features
Ambient Temp. Rang
e
°C 16 ~ 38
Setting Temp. Range °C/°F Left side 7 ~ 18 / 45 ~ 65
Ri
g
ht side 1 ~ 7
/
34 ~ 43
Power Source V/Hz 115/60
Rated Input W170
Rated Current A2.2
Noise Level dB(A) Less than 45
Defrost Type Automatic
Temp. Control Electronic
Blowing Agent Cyclopentane
Refrigerating System
Cooling System Wind cooling
Compressor
Model No. AE1350Y/HYE55Y42
Type Hermetic
LRA 13.1
RLA 2.0
Overload Protecto
r
B60-125
PTC Starter QP2-22/*
Oil /
Condenser Fan Motor Model No. YJF610A-610-RX
Rating 110-120V, 60Hz
Evaporator Fan Motor Model No. PL92B12H
Rating 12 V, 0.2A
Expansion device Capillary (Ø0.6 x 1800 mm)
Refrigerant / Charged Volume R134a / 90g
Dimensions & Weights
Net Dimensions Width - mm 624
Height - mm 856
Depth - mm 595
Packing Dimensions Width - mm 655
Height - mm 906
Depth - mm 705
Weight Net / Gross - KGS 51/58
* Specifications are subject to change without prior notice.

4
2. Name of Parts
2.1 WBV21DZ
1. WINE CHILLER TEMPERATURE CONTROL PANEL
2. INTERIOR FAN
3. INTERIOR LIGHT
4. CABINET
5. BEVERAGE CENTER TEMPERATURE CONTROL PANEL
6. WINE BOTTLE SHELVES
7. WINE BOTTLE STORAGE RACK / BASKET
8. BEVERAGE SHELVES
9. STORAGE BASKET
10. LEVELING LEGS
11. LOCK
12. CHARCOAL FILTER
15
6
12
89
10
11
7
234

5
3. REFRIGERANT CYCLE DIAGRAM
1. Compressor
2. Hot Pipe
3. Condenser (Internal)
4. Condenser Fan
5. Condenser (External)
6. Dry Filter
7. Capillary
8. Evaporator Fan
9. Evaporator
10. Accumulator

6
4. WIRING DIAGRAM
4.1 WBV21DZ
***********

7
5. COMPRESSOR VIEW AND PARTS LIST
1. Suction Pipe
2. Compressor
3. Process Pipe
Outlet Pipe of Condenser
4. Discharge Pipe
5. Condenser Fan Supporter
6. Condenser Fan Cover
7. Condenser Fan
8. Condenser Fan Motor
9. Power Supply Cord with Plug
10. Junction Box
11. Electrical Box of Compressor
12. Compressor Base
13. Compressor Junction Box
14. Compressor Junction Box supporter

8
6. HOW TO REMOVE THE SHELVES
The appliance is equipped with the wired shelves and beverage shelves. You can move the
shelves out and in smoothly.
•To prevent damaging the door gasket, make sure to have the door all the way opened when
pulling the bottom shelf out of the rail compartment.
•For easy access to the storage content, you must pull the shelf approximately 1/2 out of the rail
compartment, however this unit was designed with a plastic post on each sides of the shelf track
to prevent bottles from falling.
•When removing the shelf out of the inner rail, make sure to remove all items first. Then move the
shelf to the position where the notch of shelf is exactly under the plastic post and lift the shelf. In
order to replace the shelf, repeat steps described above in reverse.
Wire shelf Beverage shelf (glass shelf)
7 REPLACING THE BOTTOM GRILLE
1．Remove two screws that are used to fix the bottom grille with the cabinet.

9
1. The bottom grille is shown as below.
8. HOW TO REMOVE THE DOOR
Note: All parts removed must be saved to do the reinstatement of door.
1. Remove the bottom grille according to “Replacing the Bottom Grille”.
2. Pull out and remove the lower hinge cover.

10
3. Disconnect the communication cable between the door and the cabinet.
4. Pull out the wire from the cabinet.
5. Remove the upper hinge cover from the top right of the door

11
6. Remove the three screws with the upper hinge and remove the upper hinge.
7. Lift up the door slightly and remove the wire from the lower hinge.
9.RELACING THE CONTROL PANEL
1. Remove the cover behind the control panel with a screw driver.

12
2. Remove two screws that are used to fix the PCB broad.
3. Remove PCB board and disconnect the cables.

13
10. REPLACING THE MAIN PCB.
1. Lay down the cabinet to the left side and place it on a padded surface to prevent scratching it. The
main PCB is located at the bottom of the cabinet.
Note: Never lay down the cabinet to the right side as it may damage the compressor.
2. Remove the main PCB box cover

14
3. Disconnect all terminals on the main control PCB.
4. Remove four screws that are used to fix the main control PCB. Now you can replace the main
control PCB.

15
11. REPLACING THE FAN MOTOR AND EVAPORATOR
1. Remove all the shelves according to “How to remove the shelves”.
2. Remove the screws that are used to fix the air duct with the cabinet.
2. Disconnect the wires then you can replace the evaporator fan motor.

16
4. Remove screws between air dust and the evaporator fan motor, then you can replace the fan
motor.
EVAPORATOR PICTURE
*****************
12. REPLACING THE LED LIGHT ASSEMBLY
1. Remove the top two shelves according to “How to remove the shelves”.
2. Turn the light cover counter-clockwisely to remove.

17
3. Remove the two screws that are used to fix light holder.
4. Disconnect the cables then you can replace the LED light assembly.

18
13. REPLACING THE CONDENSER FAN MOTOR, THE
COMPRESSOR PTC STARTER AND OVERLOAD PROTECTOR
1．Remove the seven screws that are used to fix the condenser fan motor with the compressor
base.
2．Remove the clamp that is used to fix the junction box of compressor. Then dismantle
the junction box cover.

19
3．Disconnect the condenser fan motor cable with compressor. Now you can replace the
condenser fan motor.
4．Disconnect the compressorPTC starter and overload protector cable with compressor. Now you
can replace the compressorPTC starter and overload protector.
***********Starter and protector pictures

20
14. REPLACING THE DOOR GASKET
1. Open the door and detach the old door gasket from the doorframe by pulling off the gasket.
15. REPLACING CHARCOAL FILTRATION
1. Remove the bottles of wine stored on the two(2) shelves in front of the filter.
2. Remove the shelves and set aside to be replaced once you have changed the filter.
3. Hold the filter and turn it counter-clockwisely and then pull it out.
4. Remove the existing filter and replace with a new one.
5. Put the new filter into the hole and then turn the filter clockwisely.