Avaya ERS 4000 Series User manual

Installation Job Aid (English) for Avaya
Ethernet Routing Switch 4000 Series
(NN47205-303, ver 01.01)
How to get help
To access the complete range of services and support that Avaya provides, go to
www.avaya.com.
You can also go to www.avaya.com/support to access the following pages:
• technical documentation
• product training
• technical support
If you purchased a service contract for your Avaya product from a distributor or authorized
reseller and you need assistance, contact the technical support staff for that distributor or
reseller.
Notices
Notice paragraphs alert you about issues that require your attention. The following paragraphs
describe the types of notices used in this guide.
Note:
Notes provide tips and useful information regarding the installation and operation of Avaya
products.
November 2013 1

Electrostatic alert:
ESD
ESD notices provide information about how to avoid discharge of static electricity and
subsequent damage to Avaya products.
Caution:
Caution notices provide information about how to avoid possible service disruption or
damage to Avaya products.
Warning:
Warning notices provide information about how to avoid personal injury when working with
Avaya products.
Voltage:
Danger — High Voltage notices provide information about how to avoid a situation or
condition that can cause serious personal injury or death from high voltage or electric
shock.
Danger:
Danger notices provide information about how to avoid a situation or condition that can
cause serious personal injury or death.
Safety messages
Warning:
Installation must be performed by qualified service personnel only. Read and follow all
warning notices and instructions marked on the product or included in the documentation.
Voltage:
This equipment relies on the building's installation for overcurrent protection. Ensure that a
fuse or circuit breaker no larger than 120 VAC, 15 A U.S. (240 VAC, 16 A International) is
used on the phase conductors.
Caution:
This device is a Class A product. In a domestic environment, this device can cause radio
interference, in which case the user may be required to take appropriate measures.
Safety messages
2 November 2013

Caution:
When mounting this device in a rack, do not stack units directly on top of one another in the
rack. Each unit must be secured to the rack with appropriate mounting brackets. Mounting
brackets are not designed to support multiple units.
Voltage:
Use only power cords that have a grounding path. Without a proper ground, a person who
touches the switch is in danger of receiving an electrical shock. Lack of a grounding path to
the switch can result in excessive emissions.
Warning:
Disconnecting the power cord is the only way to turn off power to this device. Always connect
the power cord in a location that can be reached quickly and safely in case of an
emergency.
Warning:
Fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look
into an optical fiber or connector port. Always assume that fiber optic cables are connected
to a light source.
Caution:
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
Safety messages
November 2013 3

Installation preparation
Before you begin
Ensure the area where you install and use the 4000 Series switch meets the following
environmental requirements:
• Ambient temperature between 32° and 106° F (0° and 50° C)
• Relative humidity between 10% and 90% noncondensing
• No nearby heat sources such as hot air vents or direct sunlight
• No nearby sources of severe electromagnetic noise
• No excessive dust
• Adequate power source within six feet; one 15-Amp circuit required for each power supply
• At least 2 inches (5.08 cm) on all sides of the switch unit for ventilation
• Adequate space at the front and rear of the switch for access to cables
If you are installing a single Avaya Ethernet Routing Switch on a table or shelf, ensure the
surface can support at least 15 to 20 pounds (7 to 9 kilograms).
Installing the switch in an equipment rack
Required tool: Phillips screwdriver for attaching brackets to the switch.
Rack requirements:
• A space of 2.8 inches for each switch in an EIA or IEC standard 19 inch (48.2 centimeter)
equipment rack.
• The rack must be bolted to the floor and braced, if necessary.
• The rack must be grounded to the same grounding electrode used by the power service
in the area. The ground path must be permanent and must not exceed 1 ohm of resistance
from the rack to the grounding electrode.
The following figures provide instruction for installing the switch in a rack.
Note:
Avaya ERS 4000 Series hardware can vary in size and shape. Your switch might appear
different than the following example figures.
Installation preparation
4 November 2013

Attach a bracket to each side of the switch.
Slide the switch into the rack. Insert and tighten the rack mount screws.
Installation preparation
November 2013 5

Note:
The ERS 4000 Series mounting hardware is specific for each switch model. Do not mix
screws or brackets between different ERS 4000 Series switches.
Installing the switch on a table or shelf
You can install a single Avaya Ethernet Routing Switch on any flat surface that can safely
support the weight of the switch and attached cables (15 to 20 pounds or 7 to 9 kilograms).
The following figures provide instructions for installing the switch on a table or shelf.
Note:
Avaya ERS 4000 Series hardware can vary in size and shape. Your switch might appear
different than the following example figures.
Installation preparation
6 November 2013

Attach the rubber feet at the marked locations.
Installation preparation
November 2013 7

Set the switch on a table or shelf.
Note:
Allow at least 2 inches (5.1 cm) on each side for proper ventilation and at least 5 inches
(12.7 cm) at the back for power cord clearance.
AC power specifications
The following table describes the AC power specifications for the Ethernet Routing Switch 4000
Series.
Model Input
current
(amps
maximum
at 100-120
VAC)
Input
current
(amps
maximum
at 200-240
VAC)
Input
voltage
(rms, VAC
at 50-60
Hz)
Input
voltage
(rms, VAC
at 50-60
Hz)
Power
consump-
tion (watts
max)
Thermal
rating
(Btu/h
maximum)
ERS
4548GT
3 1.5 100-120 200-240 150 415
ERS
4548GT-
PWR
6.5 3.3 100-120 200-240 470 788
ERS 4550T 3 1.5 100-120 200-240 150 240
Installation preparation
8 November 2013

Model Input
current
(amps
maximum
at 100-120
VAC)
Input
current
(amps
maximum
at 200-240
VAC)
Input
voltage
(rms, VAC
at 50-60
Hz)
Input
voltage
(rms, VAC
at 50-60
Hz)
Power
consump-
tion (watts
max)
Thermal
rating
(Btu/h
maximum)
ERS
4550T-
PWR
6.5 3.3 100-120 200-240 470 615
ERS
4526FX
3 1.5 100-120 200-240 150 256
ERS
4526GTX-
PWR
6.5 3.3 100-120 200-240 470 546
ERS
4526GTX
3 1.5 100-120 200-240 150 307
ERS
4526T-
PWR
6.5 3.3 100-120 200-240 470 375
ERS 4526T 3 1.5 100-120 200-240 150 188
ERS
4524GT
3 1.5 100-120 200-240 150 290
ERS
4524GT-
PWR
6.5 3.3 100-120 200-240 470 478
ERS
4550T-
PWR+
12 6 100-120 200-240 213 726
ERS
4526T-
PWR+
12 6 100-120 200-240 119 406
ERS
4850GTS
5 2.5 100-120 200-240 94.6 323
ERS
4850GTS-
PWR+
12 6 100-120 200-240 248 846
ERS
4826GTS
5 2.5 100-120 200-240 74.3 254
ERS
4826GTS-
PWR+
12 6 100-120 200-240 149 508
Installation preparation
November 2013 9

Connecting AC power
Required cable: AC power cord that meets the requirements of your local electrical code. Refer
to the following table for plug specifications.
Table 1: International power cord specifications
Country and plug description Specifications Typical plug
Continental Europe
• CEE7 standard VII male plug
• Harmonized cord (HAR marking on
the outside of the cord jacket to
comply with the CENELEC
Harmonized Document HD-21)
220 or 230 VAC
50 Hz
Single phase
U.S./Canada/Japan
• NEMA5-15P male plug
• UL-recognized (UL stamped on
cord jacket)
• CSA-certified (CSA label secured
to the cord)
100 or 120 VAC
50-60 Hz
Single phase
United Kingdom
• BS1363 male plug with fuse
• Harmonized cord
240 VAC
50 Hz
Single phase
Australia
AS3112-1981 male plug
240 VAC
50 Hz
Single phase
The Ethernet Routing Switch 4000 Series does not have a power switch. When you connect
the AC power cord to a suitable AC power outlet, the switch powers up immediately.
Installation preparation
10 November 2013