Aventura TS-TTS01 User manual

INSTALLATION MANUAL
FOR
TS-TTS01 TRIPOD TURNSTILES
Revision
Date
Description
Initials
0
2017-07-02
New template
LR
1
2018-05-12
Manual update
KN
---
---
---
---

Page 2of 7
Index
Chapter 1 –INTRODUCTION .........................................................................................................................3
1.1. Product features ................................................................................................................................3
1.2. Product specifications........................................................................................................................3
1.3. Product dimensions ...........................................................................................................................4
Chapter 2 –INSTALLATION ...........................................................................................................................6
Chapter 3 –TROUBLESHOOTING AND SUPPORT..........................................................................................7

Page 3of 7
Chapter 1 –INTRODUCTION
This manual will address dimensions and the features of the TS-TTS01 turnstile while also
covering the process in which this turnstile is installed.
1.1. Product features
The TS-TTS01 tripod turnstiles have the following features:
-Material: standard 304 stainless steel with the option of getting 316 stainless
steel.
-Arms: manual, semi-automatic or fully automatic:
oManual: when power is off, the arms will not lower.
oSemi-automatic: when power is off, the arms will lower. The arm will not
return to the original position when power is restored.
oFull-automatic: when power is off, the arms will lower. When power is
restored, the arms will return to the original position.
-Optional: stainless steel bolt-on wheel kit.
-Customized reader cut-out or barcode reader insert.
1.2. Product specifications
The TS-TTS01 tripod turnstiles have the following characteristics:
-Power requirements: 110Vac [220Vac], 250W to 500W. The tripod turnstiles are
provided with different power supplies, based on country and customer’s
requirements. Check the product label before connecting to any power supply.
-Driver motor: 24Vdc, max. 40W
-Output interface: 12Vdc
-Communication interface: RS485
-Operating temperature: 14°F to 122°F [-10°C to 50°C]
-Operating humidity: 20% to 95% RH non-condensing

Page 4of 7
1.3. Product dimensions
Side View
Front View

Page 5of 7
Top View
Floor Template
Three Lane Layout

Page 6of 7
Chapter 2 –INSTALLATION
Before proceeding to the installation of the turnstile, unpack all components and check
to make sure the all parts from the packing slip are included, verify dimensions and conduit runs.
Use the turnstile template to properly align and lay out the site and to determine the right
location of the floor stub-ups and anchors.
Site preparation:
-Make sure that the floor is level before the installation process starts.
-When measuring the distance between the cabinets always refer to the center of
the cabinets, not the corners.
-Using the factory provided template and design layout drawings outline the exact
position of each turnstile. Make sure the floor outline includes the space
dedicated to conduit stub-ups.
-Install conduits for low voltage cables and for 110Vac (220Vac) power. Size
conduits based on the number of cables and follow local installation codes.
-On the turnstile floor footprint, locate anchoring holes. Drill and install foundation
screw bolts or M12 anchor bolts.
-Align and install the turnstile cabinet on the anchor bolts. Secure the cabinet to
the bolts.
-Follow wiring diagram to terminate the cables on the turnstile control panel. The
following connections are required:
oCard reader to control panel reader port. The control panel can be located
inside the turnstile or outside.
oLane OPEN commands (for Entry and Exit) from the turnstile to the access
control panel door open relay.
oIf required, an emergency open button or switch can be wired to the
turnstile controller board.
o110Vac (220Vac) is required for each turnstile cabinet.
-For physical installation setup look at the next drawing.

Page 7of 7
Chapter 3 –TROUBLESHOOTING AND SUPPORT
For Troubleshooting and Support, please contact Aventura Technologies Inc.:
Tel: [phone]
Fax: [phone]
Email: [email protected]
Skype: aventurasupport
Website: http://www.aventurasecurity.com