Avermedia ExtremeCap 910 User manual

CV910
Quick Guide
ExtremeCap 910
English
Deutsch
Français
Italiano
Español
Português
Português do Brasil
Pусский
Polski
Česky
Magyar
Română

European Union Directives conformance statement
Class B
This product is herewith confirmed to comply with the requirements set out in the Council
Directives on the Approximation of the laws of the Member States relating to Electromagnetic
Compatibility Directive 2014/30/EU, Directive Erp 2009/125/EC.
Responsible manufacturer:
AVerMedia Technologies, Inc.
No. 135, Jian 1st Rd.,Zhonghe Dist., New Taipei City 23585, Taiwan
TEL: [phone]
European Community contact:
AVerMedia Technologies Europe B.V.
Kwartsweg 50, 2665 NN, Bleiswijk, The Netherlands
Technical Support: http://solutions.avermedia.com/
FCC NOTICE (Class B)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference thatmay cause undesired operation.
Federal Communications Commission Statement
NOTE- This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try to
correct the interference by one ormore of the following measures:
‧Reorient or relocate the receiving antenna.
‧Increase the separation between the equipment and receiver.
‧Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
‧Consult the dealer or an experienced radio/television technician for help.

CAUTION ON MODIFICATIONS
To comply with the limits for the Class B digital device, pursuant to Part 15 of the FCC Rules, this device must be installed
in computer equipment certified to comply with the Class B limits. All cables used to connect the computer and peripherals
must be shielded and grounded. Operation with non-certified computers or non-shielded cables may result in interference
to radio or television reception.
Changes and modifications not expressly approved by the manufacturer or registrant of the equipment can void your
authority to operate the equipment under Federal Communications Commission rules.
Responsible manufacturer:
AVerMedia Technologies, Inc.
No. 135, Jian 1st Rd.,Zhonghe Dist., New Taipei City 23585, Taiwan
TEL: [phone]
USA Office contact:
AVerMedia Technologies U.S.A.
47358 Fremont Blvd., Fremont, CA 94538
Technical Support: http://solutions.avermedia.com/
CAN ICES-3 (B)/NMB-3(B)
Canada - Canada Industry Canada (IC) Labelling Requirements
Every manufacturer or importer shall ensure import or before offering for sale, as appropriate, that each unit of
the type that they offer for sale bears, in alocation convenient for inspection, a permanent label or marking
containing (in French and English), the following statement:
ICES-003 (Interference - Causing Equipment Standards)
"This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada."
The mark of crossed-out wheeled bin indicates that this product must not be disposed of with your other
household waste. Instead, you need to dispose of the waste equipment by handing it over to a designated
collection point for the recycling of waste electrical and electronic equipment. For more information about
where to drop off your waste equipment for recycling, please contact your household waste disposal service or the
shop where you purchased the product.
GOST-R Certification (Russia)
新增製造商及當地聯絡方式
新增製造商及當地聯絡方式
№ РОСС TW. AB02.B09025
Срок действия с
14.02.2013 гпо 13.02.2015 г
Москва
AB02

Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Pay attention to all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
rounding prong. The wide blade or the third prong is provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use the attachments/accessories specified by the manufacturer.
12. Unplug this apparatus during lightning storms or when unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
WARNING
To prevent fire or shock hazard do not expose the unit to rain or moisture. Dangerously high
voltages are present inside the unit. Do not open the unit. Refer servicing to qualified
personnel only.

Disclaimer
All the screen shots in this documentation are only example images. The images may vary depending on the product and
software version. Information presented in this documentation has been carefully checked for reliability; however, no
responsibility is assumed for inaccuracies. The information contained in this documentation is subject to change without
notice.
Copyright
© 2014 by AVerMedia Technologies, Inc. All rights reserved.
No part of this document may be reproduced or transmitted in any form, or by any means (Electronic, mechanical,
photocopy, recording, or otherwise) without prior written permission of AVerMedia Technologies, Inc.
Information in this document is subject to change without notice. AVerMedia Technologies, Inc. reserves the right to
modify, change, improve or enhance its products and to make changes in the content without obligation to notify any
person or organization of such changes. Please visit solutions.avermedia.com to get the updates of the operation and use
of AVerMedia products.
"AVerMedia" is a trademark and logo of AVerMedia Technologies, Inc. Other trademarks used herein for description
purpose only belong to each of their companies. Made in Taiwan (Expect Accessories).
Picture shown may vary from actual product

Quick Installation Guide
English –1
English
1
Package Contents
A. ExtremeCap 910
B. Quick Installation
Guide
C. Power Adapter
D. HDMI Cable
E. VGA Cable
F. 3.5 mm Audio Cable
G.Mini USB Cable

Quick Installation Guide
English –2
2
Hardware
2.1 Names of Parts
1. AUDIO IN
2. AUDIO OUT
3. Mini USB Port
4. SD Card Slot
5. DC IN
6. VGA OUT
7. Status Indicator
8. Microphone
9. HDMI OUT
10. VGA IN
11. VGA Indicator
12. Record Button / Indicator
13. HDMI Indicator
14. Mute Button / Indicator
15. HDMI IN
16. Power Button

Quick Installation Guide
English –3
English
2.2 Getting Started
Step 1: Connect the device to an AC outlet and a video source. Insert an SD card*.
(Refer to Chapter 3.2–3.4 for details.)
Step 2: Press to turn on the device and wait for to stop
flashing.
Ready to record voice when turns solid Green.
Ready to record voice and screen when turns solid Green
and or turns solid Green.
Step 3: Press to start recording.
* A FAT32-formatted SD card is required.
Troubleshooting
Indication
Cause
Action
SD Card Issue
Insert an SD card or free up
more space.
Signal Error
Check the cable connection,
adjust the source resolution, or
wake up the source device.

Quick Installation Guide
English –4
Task
Booting
Off
Off
Off
Flashes
Green
Ready to Record
Voice
Off
Off
Off
Solid
Green
Recording
Voice
Off
Off
Solid
Red
Solid
Green
Ready to Record
Voice + Screen
Solid
Green
or
Solid
Green
Off
Solid
Green
Recording
Voice + Screen
Solid
Green
or
Solid
Green
Solid
Red
Solid
Green
No SD Card /
SD Card Full /
Low Space
Flashes
Green
Flashes
Green
Flashes
Red
Solid
Green
Signal Error *
Off
Off
Current
Indication
Solid
Green
Updating
Firmware
Flashes
Green
Flashes
Green
Off
Solid
Green
Detecting Sound
Current
Indication
Current
Indication
Off
Green:
Moderate
Red:Loud
2.3 LED Indications and Button Functions

Quick Installation Guide
English –5
English
*A signal error can occur in the following situations:
-No signal
-HDCP signal
-Unsupported resolution
-PC or tablet in sleep mode
Check your cable connection, adjust the source resolution or wake up the source device to
solve these issues.
Status
Mute
Solid Red
Unmute
Off
Button
Functions
Press to turn on the device.
Press and hold for 4 seconds to turn off the device.
Press to start recording, press again to stop recording.
Press to mute, press again to unmute.
Press and hold to start sound test, release to stop.
turns Red when the surrounding sound is too loud. *
* Excessive sound can cause recording distortion. When the Status Indicator turns Red
constantly, lower the volume or move the device further away from the sound.
Capturing protected content like HDCP is not supported; if video source is
HDCP-protected, images will not show properly.

Quick Installation Guide
English –6
3
Installation
3.1 Video Quality and Recording Setup
AVerMedia Dashboard PC-Free helps users to set their desired video quality and
environment. You can download the software and driver at www.avermedia.com.
Step 1: Connect the mini USB port on the device to a PC using the included
mini USB cable.
Step 2: Power on the device. Install the ExtremeCap 910 Driver and run
AVerMedia Dashboard PC-Free on the PC.
Step 3: Choose your settings. Click Confirm to save the settings. Disconnect the
device from the PC before use.

Quick Installation Guide
English –7
English
3.2 Connect via VGA Cable
Rear View
Side View
Only the items marked with alphabets are supplied.
Speakers or headphones are optional.
The video input and output must be of the same type.
We recommend turning on your device before connecting a video source to avoid
signal errors. Disconnect and reconnect the source cable if signal error occurs.

Quick Installation Guide
English –8
3.3 Connect via HDMI Cable
Rear View
Side View

Quick Installation Guide
English –9
English
3.4 Connect via DVI to HDMI Converter
Rear View
Side View
For computers without an HDMI port, use a DVI-to-HDMI cable or converter.
Also connect your PC to the AUDIO IN port via the 3.5 mm audio cable.
Select “Duplicate”mode on your PC to ensure screen is recorded. For more
information, please refer to the FAQ at www.avermedia.com
Do not disconnect the power cable or remove the SD card during recording.

Quick Installation Guide
English –10

Kurzanleitung
Deutsch –1
Deutsch
1
Inhalt der Verpackung
A. ExtremeCap 910
B. Kurzanleitung
C. Netzadapter
D. HDMI-Kabel
E. VGA-Kabel
F. 3,5-mm-Audiokabel
G.Mini-USB-Kabel

Kurzanleitung
Deutsch –2
2
Hardware
2.1 Teilebezeichnung
1. AUDIO EIN
2. AUDIO AUS
3. Mini USB-Anschluss
4. SD-Kartenschlitz
5. DC EIN
6. VGA AUS
7. Statusanzeige
8. Mikrofon
9. HDMI AUS
10. VGA EIN
11. VGA-Anzeige
12. Aufnahme-Taste/
Anzeige
13. HDMI-Anzeige
14. Stummschalten-Taste/
Anzeige
15. HDMI EIN
16. Netztaste

Kurzanleitung
Deutsch –3
Deutsch
2.2 Erste Schritte
Schritt 1: Verbinden Sie das Gerät mit einer AC-Wandsteckdose und einer
Videoquelle. Legen Sie die SD-Karte* ein. (Hinweise siehe Kapitel
3.2-3.4).
Schritt 2: Drücken Sie , um das Gerät einzuschalten und warten Sie
bis nicht mehr blinkt.
Bereit für die Sprachaufzeichnung, wenn stabil Grün ist.
Bereit für die Sprach- und Bildschirmaufzeichnung, wenn
stabil Grün ist und oder stabil Grün ist.
Schritt 3: Starten Sie die Aufnahme mit .
* Die SD-Karte muss mit FAT 32 formatiert werden.
Fehlerbehebung
Anzeige
Ursache
Aktion
SD-Kartenfehler
Legen Sie die SD-Karte ein oder
machen Sie mehr Platz frei.
Signalfehler
Kabelverbindung überprüfen,
Auflösung an der Quelle prüfen
oder Quellgerät aktivieren.
Blinkt
Aus
oder

Kurzanleitung
Deutsch –4
Aufgabe
Starten
Aus
Aus
Aus
Blinkt
Grün
Sprachaufzeich
nung bereit
Aus
Aus
Aus
Stabil
Grün
Aufnahme
Sprache
Aus
Aus
Stabil
Rot
Stabil
Grün
Aufnahme bereit
Sprache +
Bildschirm
Stabil
Grün
oder
Stabil
Grün
Aus
Stabil
Grün
Aufnahme
Sprache +
Bildschirm
Stabil
Grün
oder
Stabil
Grün
Stabil
Rot
Stabil
Grün
Keine
SD-Karte/SD-Ka
rte voll/wenig
Speicherplatz
Blinkt
Grün
Blinkt
Grün
Blink
Rot
Stabil
Grün
Signalfehler *
Aus
Aus
Aktuelle
Anzeige
Stabil
Grün
Firmware-Updat
e
Blinkt
Grün
Blinkt
Grün
Aus
Stabil
Grün
Sound erkannt
Aktuelle
Anzeige
Aktuelle
Anzeige
Aus
Grün:
Moderate
Rot:Laut
2.3 LED-Meldeleuchten und Tastenfunktionen