Avery Weigh-Tronix ZK830 User manual

AWT35-501610
Issue AE
ZK830
Counting Scale
Service Manual
original instructions
CONFIDENTIAL

ZK830_s_en_501610.book
Avery Weigh-Tronix is a trademark of the Illinois Tool Works group of companies whose ultimate parent company is
Illinois Tool Works Inc (“Illinois Tool Works”). Copyright © 2018 Illinois Tool Works. All rights reserved.
No part of this publication may be reproduced by making a facsimile copy, by the making of a copy in three dimensions of a two-dimensional
work and the making of a copy in two dimensions of a three-dimensional work, stored in any medium by electronic means, or transmitted in
any form or by any means, including electronic, mechanical, broadcasting, recording or otherwise without the prior written consent of the
copyright owner, under license, or as permitted by law.
This publication was correct at the time of going to print, however Avery Weigh-Tronix reserves the right to alter without notice the
specification, design, price or conditions of supply of any product or service at any time.

ZM400 Series Indicators Service Manual 3
Table of Contents
page
Manual revision history .............................................................................................................................6
Chapter 1 General information and warnings .........................................................................................7
About this manual ..............................................................................................................7
Text conventions .........................................................................................................7
Special messages .......................................................................................................7
Installation ..........................................................................................................................8
Wet conditions .............................................................................................................8
Routine maintenance .........................................................................................................8
Cleaning the machine ........................................................................................................8
Training ..............................................................................................................................8
Sharp objects .....................................................................................................................9
FCC and EMC declarations of compliance ........................................................................9
Chapter 2 Introduction ............................................................................................................................10
Front panel .......................................................................................................................10
Front Display .............................................................................................................12
Powering up the ZK830 ...................................................................................................12
Numeric entry procedure (without optional keypad) ........................................................13
Numeric entry procedure (with optional keypad) .............................................................13
Chapter 3 Introduction to the menus .....................................................................................................14
Accessing the menus .......................................................................................................15
Exiting the menus ............................................................................................................15
Menu annunciators ..........................................................................................................16
Chapter 4 User level menus ....................................................................................................................17
User menu .......................................................................................................................17
Time ..........................................................................................................................18
Date ...........................................................................................................................18
Site ID ........................................................................................................................19
Seal ...........................................................................................................................19
About menu ......................................................................................................................20
Boot (Bootloader) ......................................................................................................21
Firmware ...................................................................................................................21
App ............................................................................................................................21
Serial .........................................................................................................................21
Enet ...........................................................................................................................22
Download ..................................................................................................................23
BSQ ...........................................................................................................................23
Audit menu .......................................................................................................................24
Counter ......................................................................................................................24
Chapter 5 Diagnostics level menus .......................................................................................................25
Diag menu ........................................................................................................................25
Scale .........................................................................................................................26
Current Zero .............................................................................................................26
Display .......................................................................................................................27
Buttons ......................................................................................................................27
Ports ..........................................................................................................................27
Inputs .........................................................................................................................28
Outputs ......................................................................................................................28

4 ZM400 Series Indicators Service Manual
Logs ..........................................................................................................................29
BSQ ...........................................................................................................................29
Chapter 6 ADMIN level menus ................................................................................................................ 31
Setup menu .....................................................................................................................31
Calibration Procedure ...................................................................................................... 32
Scale 1-2 ................................................................................................................... 32
Zero Procedure ......................................................................................................... 33
Span Procedure ........................................................................................................ 34
Linearity Procedure ................................................................................................... 34
Input procedure ......................................................................................................... 35
Gravity Factor Procedure .......................................................................................... 36
Display ...................................................................................................................... 37
Calibration Unit .......................................................................................................... 37
Print calibration report ............................................................................................... 37
Scale ................................................................................................................................ 38
Scale 1-2 ................................................................................................................... 39
Capacity .................................................................................................................... 39
Division ......................................................................................................................39
Units ..........................................................................................................................40
Stable ........................................................................................................................40
AZT ...........................................................................................................................41
Filter .......................................................................................................................... 41
Ranges ...................................................................................................................... 43
2,3,Range .................................................................................................................. 44
Type ..........................................................................................................................45
System ............................................................................................................................. 46
Default Values ........................................................................................................... 46
Site ............................................................................................................................ 48
Display ...................................................................................................................... 48
Buttons ...................................................................................................................... 49
Display values ........................................................................................................... 49
Tare ...........................................................................................................................50
Config ........................................................................................................................ 51
Serial .........................................................................................................................51
App ............................................................................................................................51
Password .................................................................................................................. 52
Z-Lock ....................................................................................................................... 52
Beeper ....................................................................................................................... 52
Number of Scales ...................................................................................................... 53
Ports ................................................................................................................................ 54
Serial .........................................................................................................................55
Ethernet ..................................................................................................................... 55
Protocol ..................................................................................................................... 57
P.F.Edit ..................................................................................................................... 59
Interlock .....................................................................................................................59
Input ................................................................................................................................. 60
Output .............................................................................................................................. 61
Chapter 7 Communication port protocols ............................................................................................ 62
SMA Protocol ...................................................................................................................62
Level 1 and 2 Commands ........................................................................................ 62
Standard Scale Response Message ......................................................................... 63
Unrecognized Command Response ......................................................................... 63
About Command Response ...................................................................................... 63
Scale Information Command Response ................................................................... 64
Avery Weigh-Tronix Extended SMA Commands ...................................................... 65

ZM400 Series Indicators Service Manual 5
ENQ, Print & B-Cast command and response protocols .................................................66
Scanner commands and responses ..........................................................................66
Scanner bar codes ....................................................................................................67
Commands and responses ..............................................................................................69
Chapter 8 Option cards ...........................................................................................................................72
Wireless Ethernet communication (802.11g) card ...........................................................73
Analog Scale Input Option with 5VDC Excitation .............................................................74
Error code ..................................................................................................................74
Chapter 9 Printed reports .......................................................................................................................75
Calibration report .............................................................................................................75
Chapter 10 Print formatting ....................................................................................................................76
Print Format Editor ...........................................................................................................76
Editing an existing print string ..........................................................................................77
Inserting characters ...................................................................................................78
Deleting characters ...................................................................................................79
Inserting tokens, etc. ........................................................................................................81
Other scale tokens ...........................................................................................................83
Transmitting leading zeroes .............................................................................................84
Print format errors ............................................................................................................85
Chapter 11 Application Notes .................................................................................................................87
I/O interfaces ....................................................................................................................87
Inputs .........................................................................................................................87
Outputs ............................................................................................................................88
Relays .......................................................................................................................88
Opto module ..............................................................................................................88
Transistor outputs ......................................................................................................89
Diagnostics ......................................................................................................................89
Chapter 12 Print tokens, parameters and default print formats ..........................................................90
Notes on width syntax ......................................................................................................90
Explanation of width syntax for WEIGHT (integers) ..................................................90
Explanation of width syntax for WEIGHT (strings) ....................................................90
Explanation of width syntax for UNITS OF MEASURE (strings) ...............................90
Firmware tokens ..............................................................................................................91
Additional token tables ..............................................................................................95
App tokens .......................................................................................................................96
ASCII characters ..............................................................................................................97
Control codes ...................................................................................................................98
Default print formats .........................................................................................................99
Chapter 13 Complete menu structures ................................................................................................103
Chapter 14 Technical illustrations .......................................................................................................109
ZK830 Exploded drawing ...............................................................................................109
BSQ 35 and 80kg base exploded drawing .....................................................................110
BSQ 1 and 5kg base exploded drawing .........................................................................111
ZK830 and BSQ service parts kits .................................................................................112
ZK830 and BSQ service parts kits (continued) ..............................................................113
System block diagram ....................................................................................................114
Clamp down plate drilling templates ..............................................................................115
Index .......................................................................................................................................................117

ZK830 Counting Scale Service Manual 6
Manual revision history
Current
Issue Date Created Details of Changes
AA February 2017 New manual
AB August 2017 Added BSQ parts kits in chapter 12
AC November 2017 Updated token table in chapter 10.
AD May 2018 Fixed some items in table in section 7.4. Fixed scanner protocols. Added chapter 8 and 11 to the
book.
AE June 2018 Added clamp down plate drilling templates in chapter 14.

ZK830 Counting Scale Service Manual 7
1.1 About this manual
1 General information and warnings
1.1 About this manual
This manual is dividedinto chapters by the chapter number and the large text at the top
of a page. Subsections are labeled using the 1.1 and 1.1.1 convention. The names of
the chapter and the next subsection level appear at the top of alternating pages of the
manual to remind you of where you are in the manual. The manual name and page
numbers appear at the bottom of the pages.
1.1.1 Text conventions
Key names are shown in bold and reflect the case of the key being described. If a key
has dual functions,the function is shown first followed by the keyname in parentheses
and in bold, such as in these examples: F1, SELECT, PRINT, etc.
Displayed messages appear in bold italic type and reflect the case of the displayed
message.
1.1.2 Special messages
Examples of special messages you will see in this manual are defined below. The
heading words have specific meanings to alert you to additional information or the
relative level of hazard.
ELECTRICAL WARNING!
THIS IS AN ELECTRICAL WARNING SYMBOL.
ELECTRICAL WARNINGS MEAN THAT FAILURE TO FOLLOW
SPECIFIC PRACTICES OR PROCEDURES MAY RESULT IN
ELECTROCUTION, ARC BURNS, EXPLOSIONS OR OTHER HAZARDS
THAT MAY CAUSE INJURY OR DEATH.
WARNING!
This is a Warning symbol.
Warnings mean that failure to follow specific practices and procedures may
have major consequences such as injury or death.
CAUTION!
This is a Caution symbol.
Cautions give information about procedures that, if not observed, could result
in damage to equipment or corruption to and loss of data.
NOTE: This is a Note symbol. Notes give additional and important information, hints
and tips that help you to use your product.

8 ZK830 Counting Scale Service Manual
1 General information and warnings
1.2 Installation
1.2.1 Wet conditions
Under wet conditions, the plug must be connected to the final branch circuit via an
appropriate socket / receptacle designed for washdown use.
Installations within the USA should use a cover that meets NEMA 3R specifications
as required by the National Electrical Code under section 410-57. This allows the unit
to be plugged in with a rain tight cover fitted over the plug.
Installations within Europe must use a socket which provides a minimum of IP56
protection to the plug / cable assembly. Care must be taken to make sure that the
degree of protection provided by the socket is suitable for the environment.
1.3 Routine maintenance
Always turn off the machine and isolate from the power supply before starting any
routine maintenance to avoid the possibility of electric shock.
1.4 Cleaning the machine
1.5 Training
Do not attempt to operate or complete any procedure on a machine unless you have
received the appropriate training or read the instruction books.
NO USER SERVICEABLE PARTS. REFER TO QUALIFIED SERVICE
PERSONNEL FOR SERVICE.
IMPORTANT: This equipment must be routinely checked for proper operation
and calibration.
Application and usage will determine the frequency of calibration required for
safe operation.
Table 1.1 Cleaning DOs and DON’Ts
DO DO NOT
Wipedowntheoutsideofstandardproducts
withacleancloth,moistenedwithwaterand
a small amount of mild detergent
Attempt to clean the inside of the machine
Use harsh abrasives, solvents, scouring cleaners or
alkaline cleaning solutions
Spray the cloth when using a proprietary
cleaning fluid Spray any liquid directly on to the display windows

ZK830 Counting Scale Service Manual 9
1.6 Sharp objects
To avoid the risk of RSI (Repetitive Strain Injury), place the machine on a surface which
is ergonomically satisfactory to the user. Take frequent breaks during prolonged usage.
1.6 Sharp objects
Do not use sharp objects such as screwdrivers to operate the keys.
1.7 FCC and EMC declarations of compliance
United States
Canada
European Countries
This equipment has been tested andfound to comply with the limits for a Class A digital device, pursuanttoPart15 of the FCCRules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de
la Classe A prescrites dans le Règlement sur le brouillage radioélectrique edicté par le ministère des Communications du Canada.
WARNING: This is a Class Aproduct.Inadomesticenvironment,thisproductmaycause radio interference in which the usermaybe
required to take adequate measures.

ZK830 Counting Scale Service Manual 10
2 Introduction
2.1 Front panel
The front panels for the ZK830 main display and optional keypad are shown in Figure
2.1 and consists of the keys and the display.
Figure 2.1 Front panel with optional keypad
See the price list for option kits available for the ZK830. Installation instructions are
included in each kit.
lb
kg
GROSS
NET
TARE PRINT SP PCWT%TOTAL
g
COUNT
HI RES
ZK830
THE COUNT ING
FEATURE IS NOT LEGAL
FOR TRADE
TARE SELECT UNITSPRINT
SAMPLE
ZERO
F1
SCALE
F2
PLU
PCWT
F3
F4
PT
12
1 23
4 56
7
89
C 0.
Never press a key with anything but your finger. Damage to the overlay may result if
sharp or rough objects are used.

ZK830 Counting Scale Service Manual 11
2.1 Front panel
The normal function of the keys on the front panel of the ZK830 are listed below.
Press the TARE key to perform a tare function.
With no weight on the scale, press the TARE key to clear a tare value.
Acts as an up arrow key for menu navigation.
Allows you to access minus and comma signs.
Acts as an ABORT key during the sampling process.
Press the SELECT key to toggle between the active display values.
Press and hold to enter the setpoint editor in all applications.
Acts as a down arrow key for menu navigation.
Allows you to access minus and comma signs.
Press the ZERO key to zero the display.
Acts as an ENTER key to accept a displayed value or function.
Press the PRINT to send information to a peripheral device through a configured
communications port. Press and hold the PRINT key to print accumulated totals, if
enabled.
Acts as a left arrow key for menu navigation.
PresstheUNITS key toscrollthroughtheavailable unitsofmeasurewhile innormal
operating mode.
Acts as a right arrow key for menu navigation.
Press the SAMPLE key to select application specific choices.
Aborts a numeric entry and acts as an ESCAPE key in the menu navigation.
Also used to display or enter an accumulator channel.
Press and hold to view the password entry screen for menu access.
Keys on the optional keypad shown below:
Press the SCALE key to switch between two attached scales.
PressthePLU keytoaccess thePLUlist. Inthecounting applicationthis keycanbe
usedtoupdatepieceweight and/or tare weightifenabled.With anactivePLU,press
the PLU key three times to update pieceweight and tare weight.
Press the PCWT key to enter a known piece weight.
If enabled, allows the user to see a high resolution weight value.
In the count application allows you to enter or view piece weight values.
Use the numeric keypad to enter values or clear a value from the display (C key).
TARE
SELECT
ZERO
PRINT
UNITS
SAMPLE
F1
SCALE
F2
PLU
F3
PCWT
F4
123
456
789
C0.

12 ZK830 Counting Scale Service Manual
2 Introduction
2.1.1 Front Display
Annunciators
The display annunciators are defined in Figure 2.2.
Figure 2.2 Display annunciators
Thetriangularannunciators will light during operation to inform the user of the weighing
mode, active unit of measure, etc.
2.2 Powering up the ZK830
The ZK830/BSQ comes with a base mounted AC power supply unit (PSU) connected
to the back of the BSQ. This supplies the required input power of 12 to 36 VDC @
200ma minimum and is connected to a properly grounded outlet (100 VAC - 240 VAC,
50 or 60 Hz). The indicator is always ON as long as power is received.
If using the optional rechargeable battery pack mounted on the rear of the base you
can expect 16 hours of operation between charges. Recharge time is four hours using
the in-line PSU. The battery pack requires 24 to 36V to charge. The battery timer
setting can be used to turn the indicator display OFF automatically.
The ZQ-BAT can also be use when using the optional column. This battery can last up
to 25 hours of continuous use or one to two weeks of occasional operation.
You can also power the indicator with a 12 to 36 VDC power supply (150ma minimum
at24VDC)via a 2.1mm centerpositivebarreljack pluggedintothereceiverontheback
of the indicator.
lb
kg
GROSS
NET
TARE
0
g
COUNT
HI RES
PRINT SP % PCWT TOTAL
center-of-zero
motion
battery status
setpoints
print
bargraph
Net weight
Tare weight
pieceweight
Gross weight
percent total
count
high resolution
Unit of
measure
Ethernet
connection

ZK830 Counting Scale Service Manual 13
2.3 Numeric entry procedure (without optional keypad)
2.3 Numeric entry procedure (without optional keypad)
The keys in Figure 2.3 have alternate functions in numeric entry screens.
Figure 2.3 Key function during numeric entry
In numeric entry screens, the center segments shown in Figure2.3flash. Use the keys,
as described in Figure 2.3, to enter a value on the display. Following is an example:
Example: To key in the number 507:
Repeatedly press the TARE()or SELECT()key until 5appears on the display.
Press the UNITS()key once to move cursor one space to the right.
Repeatedly press the TARE()or SELECT()key until 0appears on the display.
Press the UNITS()key once to move cursor one space to the right.
Repeatedly press the TARE()or SELECT()key until 7appears on the display.
Press the ZERO key to enter or accept the value.
Press the PRINT()key to move the entry function one digit to the left. This effectively
deletes the current value in that position and allows you to enter a new value in that
position.
2.4 Numeric entry procedure (with optional keypad)
Use the optional numeric keypad to input all numbers. Press the ZERO key to enter or
accept the value.
These segments flash in alphanumeric entry mode
Press to increment the flashing number
Press to decrement the flashing number
Press to backspace cursor in a number
Press to advance cursor in a number
Press to accept a value
Press to escape an entry screen
TARE / -
SELECT / -
PRINT / -
UNITS / -
ZERO / -
F1 / ESC -

ZK830 Counting Scale Service Manual 14
3 Introduction to the menus
Menus, accessed through passwords, are available in the indicator to customize and
configure the indicator for your purposes. The menu levels and their passwords are
shown below:
Some menus appear in more than one menu level. As you can see in the table above,
the 111 password gives you access to three menus; User, About and Audit. The 3570
password gives you access to those three plus the Diagnostics menu. The 3088
password gives you access to those four plus the Setup menu.
This allows the supervisor to control access to some or all of the menus based on the
passwords shared. The menus are the same no matter which menu level you access
them from.
See Numeric entry procedure (without optional keypad) on page 13 for instructions on
how to enter a password to get to the menus. Key functions in the menus are shown
below.
Menu Navigation Keys:
Password Menu Level Accessed Menus
111 USER User, About, Audit
3570 DIAGNOSTICS Diag, User, About, Audit
3088 ADMIN Setup, Diag, User, About, Audit
2580 CALIBRATE Calib
1793 SUPER Application specific items. See User manual.
The CALIBRATE menu level accesses the calibration procedure only. You can also
access the calibration menu through the Setup menu using the ADMIN password.
The menus are always explained in a sequential manner to cover all information in a
logical fashion. You will probably never access all the menu items in this manner. You
can navigate to the area of the menu that needs to be changed by using the menu
maps and key navigation legends which are inserted as a reminder with most menus.
Press SELECT/ to move down in a menu
Press TARE/ to move up in a menu, except at the
bottom item in a menu, then use ZERO/ or F1
Press PRINT/ to move left in a menu
Press UNITS/ to move right in a menu
Press ZERO/ to accept a value or choice and
move up in the menu.
Press F1 to escape and move up in the menu

ZK830 Counting Scale Service Manual 15
3.1 Accessing the menus
3.1 Accessing the menus
Follow these steps to access the various menus in the indicator.
1. With the indicator powered up and in normal operating mode, press and hold
the SAMPLE/F1 key …
Pass is briefly displayed, then a flashing 0, prompting you to enter the
password.
2. Key in the password for the menu you want to access and press the ZERO key
to accept it …
The first item in the top level of the menu you accessed is displayed.
3. Use the navigation keys, shown below, to navigate through the menu
structure. The symbols appear on the bottom of the keys.
Menu Navigation Keys:
3.2 Exiting the menus
1. If you are at the bottom item in a menu use ZERO to accept a choice or value
and move up a level, or use F1 to escape and move up one level without
accepting the choice or value. From that point, press the TARE key repeatedly
until …
SAVE no is displayed. This means “Do not save changes. “
2. Use the PRINT or UNITS key to scroll through the choices: SAVE no,
SAVEYES and CAnCEL. Press ZERO to accept the displayed choice.
If you choose SAVE no or SAVEYES the indicator exits the menu and
returns to normal weighing mode.
OR
If you choose CAnCEL, the indicator remains in the menu.
When the 0is flashing, press F1 and the application name is briefly displayed, then
the indicator returns to normal operating mode.
Press SELECT/ to move down in a menu
Press TARE/ to move up in a menu, except at the
bottom item in a menu, then use ZERO/ or F1
Press PRINT/ to move left in a menu
Press UNITS/ to move right in a menu
Press ZERO/ to accept a value or choice and
move up in the menu.
Press F1 to escape and move up in the menu

16 ZK830 Counting Scale Service Manual
3 Introduction to the menus
3.3 Menu annunciators
The menu structure is made up of menu items, parameters, value entry screens and
lists from which you choose one item. To help you know where you are in the menu,
the bar graph at the top of the display is on while the indicator is in the menus and will
change appearance according to the following rules:
All segments flashing This means you are inthe menu structure but not
in any of the following screens.
Center flashing / others off This means you are in a numeric entry screen.
Enter a number and press ZERO to accept.
Right flashing / others off This means you are in a list. Scroll through the
choices with the PRINT and UNITS keys and
press ZERO to accept.
Left flashing / others off This means you are in a data entry.
Every alternate segment flashing This means you are in octet entry for IP, Subnet
or Gateway address.

ZK830 Counting Scale Service Manual 17
4.1 User menu
4 User level menus
The USER level (password 111) contains the User, About, and Audit menus arranged
as shown in Figure 4.1.
Figure 4.1 USER level (password 111) menus
To access the USER level, from normal weighing mode, press and hold the SAMPLE/
F1 key. Enter password 111 and press the ZERO key.
4.1 User menu
The User menu is shown in Figure 4.2.
Figure 4.2 User menu
Use this menu to set the time, date, site ID, to see the physical seal status and print
archive information. Each is explained below:
See
page 17 See
page 20 See
page 24
User About Audit
User
Site ID Seal
Enter
Site ID View Seal
Status
Time Date
Set
12hr 12hr-AP 24hr
Set Style
MMDD4YMMDD2Y DDMM2Y DDMM4Yy- x
m- x
d- x
Style
h- x
m- x
s- x
Reference
Numeric entry procedure
(without optional keypad)
on page 13

18 ZK830 Counting Scale Service Manual
4 User level menus
4.1.1 Time
SEt Use this to enter values for the time.
h- x, = Hour
m- x = Minute
s- x = Seconds
StYLE Choose the style of the time display. Choices are:
12hr, = 12 hour clock
12hr-AP = 12 hour clock with AM/PM
24hr = 24 hour military time
4.1.2 Date
Use the dAtE item to set the year, month and day and the style of the displayed date.
SEt Enter values for the date.
y- x = Year
m- x = Month
d- x = Day
Use the tiME menu item to set the clock
(SEt) and to choose the style of the time
display (StYLE) 12 hr, 12 hr AM/PM or
24 hr.
Time
Set
12hr 12hr-AP 24hr
Style
h- x
m- x
s- x
The Time and Date can be used in print formats.
Date
Set Style
MMDD4YMMDD2Y DDMM2Y DDMM4Yy- x
m- x
d- x

ZK830 Counting Scale Service Manual 19
4.1 User menu
StYLE Choose the style of the date display. Choices are:
MMdd2Y = Month, Day, 2-digit Year
MMdd4Y = Month, Day, 4-digit Year
ddMM2Y = Day, Month, 2-digit Year
ddMM4Y = Day, Month, 4-digit Year
4.1.3 Site ID
4.1.4 Seal
To exit the menu, see Exiting the menus on page 15.
The seal switch jumper, P7, is located near the bottom center of the main PCB. See
jumper settings in chapter 13. If the jumper is installed, the indicator is sealed. This
means the only the Diagnostic, User, About, Audit and Supervisor menus can be
accessed. Other menus cannot be accessed - the display will flash SEALEd.
SitE Use this to enter a Site ID.
The Site ID can be used in a print format. Use the
alphanumeric entry methods described in 2.3 to enter a
Site ID. (maximum 6 digits)
Site ID
Enter
Site ID
SEAL Use this to view the seal status of the indicator.
This is the status of the physical seal jumper inside the
indicator. If the unit is sealed, no changes can be made to
the configuration of the indicator. See the note below.
Seal
View Seal
Status

20 ZK830 Counting Scale Service Manual
4 User level menus
4.2 About menu
The About menu is shown in Figure 4.3.
Figure 4.3 About menu
Usethismenutodisplayinformation aboutthevariousitemsshown in Figure 4.3. Each
is explained below:
BSQ
Sw Part
Version
Cur. Ser
xxxx
xxxxx
(View
software PN) (View software
version)
xxxx
(View
cell SN)
xxxxxx
Serial
About
App. EnetFirmBoot
VersionPartno IP GatewaySubnet
VersionPartno
(View
bootloader PN)
VersionPartno
(View version)
Mac
1 xx
2 xx
3 xx
4 xx
5 xx
6 xx
1 xx
2 xx
3 xx
4 xx
1 xx
2 xx
3 xx
4 xx
1 xx
2 xx
3 xx
4 xx
(View SN)
xxxx xxxxx
Dload
Sserial Dserial
(View
license
number)
(View
license
number)
(View App PN)
AWT30 XXXXX (View version) X.X.X.XX
(View Firmware PN)
AWT30 XXXXX (View version)
X.X.X.XX
AWT30 XXXXX X.X.X.XX
Scale X
Cal. Ser
(View SN of
calibrated
cell)
Reference Numeric entry procedure (without
Definitions:
Bootloader Software that makes the electronics run.
Firmware Embedded system software that creates core functions of the product.
App Specific software that controls the behaviour for a given installation.