OHAUS Dial-O-Gram User manual

Ohaus CorporationOhaus Corporation
Ohaus CorporationOhaus Corporation
Ohaus Corporation
29 Hanover Road
Florham Park NJ
07932-0900
Harvard Trip Balance
Dial-O-Gram
Model 2060
Instruction manual
®

2
INTRODUCTIONINTRODUCTION
INTRODUCTIONINTRODUCTION
INTRODUCTION
This manual covers Installation, Operation and Maintenance for the Ohaus,
Dial-O-Gram® Model 2060 Balance. To ensure proper operation of the Balance,
please read this manual completely.
DESCRIPTIONDESCRIPTION
DESCRIPTIONDESCRIPTION
DESCRIPTION
The Ohaus Dial-O-Gram®Balance is a precision weighing instruments, designed
to provide years of service with virtually no maintenance. Dial-O-Gram®Balance
employsatwo-pandesignbasedontheclassicRobervalbalanceprinciple. Ithas
the additional advantages of magnetic damping and integral dial for direct
weighing.
Two pan Balances of this type are commonly used for comparative weighing to
determine the difference in mass between two objects rather than their absolute
value, a built-in dial assembly of 100 grams capacity is usually sufficient for this
purpose. A 225g tare beam is standard on the 2060. The Model 2060 has a
weighing range of 100g and a readability of 0.1g. Maximum Balance capacity is
2kg/5lbs. The Platforms used on the Balance are 6" diameter stainless-steel.
Dial-O-Gram Balance Model 2060

3
UNPACKINGUNPACKING
UNPACKINGUNPACKING
UNPACKING
Dial-O-Gram®Model 2060 Balances are shipped as follows:
•Completely assembled Balance
•Instruction manual
•Warranty card
Your new precision Balance has been packed in a carton specifically designed to
protect it during shipment. Follow these instructions and your Balance will be
operational in just a few minutes. Carefully unpack and verify that all items are
on hand.
1. Remove the Balance from the carton by pulling on the cardboard insert.
2. Remove cardboard inserts from Balance.
3. Remove the two round rubber beam retainers from between the base and
beam end loops. All packing material should be retained if you anticipate
any future shipment of the Balance.
INSTALLATIONINSTALLATION
INSTALLATIONINSTALLATION
INSTALLATION
Place the Balance on a reasonably flat, level surface away from sources of
vibration and drafts. On such a surface a very near balance should be attained
with the Dial at zero and Tare Poise against its stop at the left end of the beam.
OPERATIONOPERATION
OPERATIONOPERATION
OPERATION
Zeroing the BalanceZeroing the Balance
Zeroing the BalanceZeroing the Balance
Zeroing the Balance
To set the Balance exactly at zero, adjust the knurled Zero Adjust Knob which is
located at the right end of the Beam. It is advisable to check the zero balance
periodically because foreign material may accumulate on the Platform or the
Beams. Thiscanproduceaslightchangeinthezerobalanceposition. Inaddition,
whenever the Scale is moved, the zero balance mustmust
mustmust
must be rechecked. Any
appreciable change in the inclination of the working surface will affect accuracy.
The base of each Balance is leveled on a surface plate at the factory and will rest
evenly on any perfectly flat surface. The Balance may rock slightly if the working
surface is not absolutely flat. This should be eliminated by shimming under the
base. Be sure to adjust the zero balance after leveling.

4
WeighingWeighing
WeighingWeighing
Weighing
Before each weighing, be sure the Dial is set at zero, and the pointer is lined up
perfectly with the zero indicator.
The specimen to be weighed is placed on the left Platform of the Balance. The
Dialisthenrotateduntil theBeamre-balances. Noticethatmagneticdampinghas
beenprovidedtobring theBeamto restquickly. Becauseofthedamping, thefinal
balance position must be achieved by turning the Dial knob slowly. With a little
practice, you will become proficient in learning exactly how fast to turn the Dial to
come to the balance position the first time. Since the capacity of the Balance far
exceeds the Dial capacity, the use of additional masses is necessary to take
advantage of the full capacity. Ohaus recommends Mass set No. 213-16 (1000g
x 1g).
For weights over 100 grams to capacity, it is easier to always set the Dial at 100
grams first. Then additional weights are placed on the right Platform of the
Balance until the total of these weights comes to within 100 grams. Then
rebalance by turning the Dial in a counter-clockwise direction from 100 grams to
its balanced position.
Use of the Tare PoiseUse of the Tare Poise
Use of the Tare PoiseUse of the Tare Poise
Use of the Tare Poise
This model is equipped with a Tare Beam assembly. A patented Tare Poise can
beusedtotareoffcontainerswhichweighlessthan200grams. Withthecontainer
onthelefthandPlatform,slidetheTarePoisetoapositionontheTareBeamwhich
indicates approximate balance. Rotate the Poise in either direction to position it
precisely on the Tare Beam to counterbalance the container on the left hand
Platform. When not in use, the Tare Poise is to be moved all the way to the left
of the Tare Beam. The spring inside the tare poise should also be pushed to its
left most position in order to obtain zero balance.
Reading the VernierReading the Vernier
Reading the VernierReading the Vernier
Reading the Vernier
Each graduation on the Dial has a value of 1 gram. A vernier adjacent to the Dial
divides these values to .1 gram increments. To read the vernier, read the lowest
gram value adjacent to the zero vernier graduation. Add to that the vernier
graduation at the vernier line which most closely lines up with any other Dial
graduations. The following illustration indicates a reading of 67.4 grams.

5
Specific Gravity DeterminationSpecific Gravity Determination
Specific Gravity DeterminationSpecific Gravity Determination
Specific Gravity Determination
A Clamp and Rod Support, Ohaus part number 183-00, is an accessory used to
elevate the Balance for suspending a specimen in water. The rod is inserted into
the1/2inchrecessontheundersideofthebase. Bymeansofafinewireorthread,
the specimen is attached to the check pin which connects the platform loop to the
checkrod. Theprocedureforweighingasuspendedspecimenisthesameasthat
for weighing an unknown mass on the Platform.
CARE AND MAINTENANCECARE AND MAINTENANCE
CARE AND MAINTENANCECARE AND MAINTENANCE
CARE AND MAINTENANCE
The following practices will assure that your Balance will give you years of
satisfactory and trouble-free service.
When the Balance is not in use, remove any mass or weights from the Platforms.
Move the Tare Poise from zero so that the Balance is not in equilibrium. This will
stop the Balance from oscillating and prevent unnecessary wear.
Use and store the Balance in places free of vibration. NeverNever
NeverNever
Never lubricate the scale
bearings. The bearings in these Balances are high grade polished agate V-blocks
and the knife edges are hardened, precision-ground steel. This type of bearing
works most efficiently when clean and dry. Keep the Balance clean at all times,
being particularly careful not to let dirt accumulate in the vicinity of the bearings. If
thebearingsshouldbecomedirty,trytocleanthemusinganairsyringe. TheModel
106-00BalanceCoverisrecommendedtokeeptheBalancecleanwhennotinuse.
Cleaning Magnet FacesCleaning Magnet Faces
Cleaning Magnet FacesCleaning Magnet Faces
Cleaning Magnet Faces
In general, most foreign matter may be easily removed by an air syringe. If the
damper vane still does not move freely, proceed as follows:
1. CAREFULLYCAREFULLY
CAREFULLYCAREFULLY
CAREFULLY turn the Balance on its side.
2. Remove the four (4) screws that mount the magnet case to the underside of
the base.
3. Remove the magnet case.
4. Cleanthemagnetfacesbypressingapieceofadhesive-backedtapeagainst
them.
5. Reinstall the magnet case.

6
PARTS INFORMATIONPARTS INFORMATION
PARTS INFORMATIONPARTS INFORMATION
PARTS INFORMATION
Ifyou requirereplacementpartsor wouldliketopurchase accessories,pleasecall
Ohaus Corporation toll-free at [phone]. An Ohaus Product Parts
Specialist will be available to help you.
ACCESSORIESACCESSORIES
ACCESSORIESACCESSORIES
ACCESSORIES
DESCRIPTION OHAUS PART NO.
Polypropylene footed scoop, (12" x 6" x 2.75" deep) and 107-00
Counterweight
Stainless steel footed scoop, (12" x 6" x 2.75" deep) and 107-S0
Counterweight
Specific gravity rod and clamp 183-00
Weight set, Metric, 1000 gram x 1 gram 213-16
Vinyl dust cover, 16" x 9.5" x 7" 106-00
Ohaus Corporation offers a full line of precision mechanical balances, individual
masses and mass sets for education and industry.
Visit our website www.ohaus.com
SERVICE INFORMATIONSERVICE INFORMATION
SERVICE INFORMATIONSERVICE INFORMATION
SERVICE INFORMATION
For service assistance in the United States, please call Ohaus Corporation toll-
free at [phone]. An Ohaus Product Service Specialist will be available to
help you.
SPECIFICATIONSSPECIFICATIONS
SPECIFICATIONSSPECIFICATIONS
SPECIFICATIONS
MODEL 2060-00MODEL 2060-00
MODEL 2060-00MODEL 2060-00
MODEL 2060-00
Capacity (g) 2000
Dial capacity x readability 100g x 0.1g
Tare range 225g
Platform size (in/cm) 6/15.2 dia.
Dimensions (W x H X D) (in/cm) 14 x 9.5 x 7/35.5 x 24.1 x 17.8
Net weight (lb/kg) 4.7/2.1
Shipping weight (lb/kg) 5/2.3

7
LIMITED WARRANTYLIMITED WARRANTY
LIMITED WARRANTYLIMITED WARRANTY
LIMITED WARRANTY
Ohausproductsarewarrantedagainstdefectsinmaterialsandworkmanshipfrom
thedateofdeliverythroughthedurationofthewarrantyperiod.Duringthewarranty
period Ohaus will repair, or, at its option, replace any component(s) that proves to
be defective at no charge, provided that the product is returned, freight prepaid, to
Ohaus.
This warranty does not apply if the product has been damaged by accident or
misuse, exposed to radioactive or corrosive materials, has foreign material
penetrating to the inside of the product, or as a result of service or modification by
other than Ohaus. In lieu of a properly returned warranty registration card, the
warranty period shall begin on the date of shipment to the authorized dealer. No
other express or implied warranty is given by Ohaus Corporation. Ohaus Corpo-
ration shall not be liable for any consequential damages.
As warranty legislation differs from state to state and country to country, please
contact Ohaus or your local Ohaus dealer for further details.

Ohaus Corporation
29 Hanover Road,
Florham Park, NJ 07932, USA
Tel: [phone],
Fax: [phone]
With offices worldwide.
P/N 1348 R0500 © Ohaus Corporation 2000 all rights reserved.