Avidsen HomeSmoke User manual

WIFI-CONNECTED
SMOKE DETECTOR
HomeSmoke
EN Ref.127065
www.avidsen.com
V1
TECHNICAL
SUPPORT
1.5V AA X2 90dB WIRELESS EASY
TO INSTALL
WARRANTY
YEARS
Works
with the app
avidsen Home

CONTENTS
A - SAFETY INSTRUCTIONS
1 - OPERATING PRECAUTIONS 04
2 - DESCRIPTION 04
3 - IMPORTANT SAFETY INFORMATION 04
4 - MAINTENANCE AND CLEANING 05
5 - RECYCLING 05
B - PRODUCT DESCRIPTION
1 - KIT CONTENTS 06
2 - SMART SMOKE DETECTOR 06
3 - INSTALLATION AREA 07
C - INSTALLATION
1 - INSTALLING THE DETECTOR ON THE WALL OR CEILING 08
2 - REPLACING THE BATTERIES 08
D - BEGINNING OPERATION
1 - INDICATOR LIGHT 09
2 - CONNECTION 09
2.1 - Installing the mobile application and creating an account 09
2.2 - Connecting the smoke detector 10
WIFI-CONNECTED SMOKE DETECTOR

EN3
E - USE
1 - USE VIA THE APP 13
F - TECHNICAL AND LEGAL INFORMATION
1 - TECHNICAL CHARACTERISTICS 13
2 - WARRANTY 14
3 - HELP AND ADVICE 14
4 - EU DECLARATION OF CONFORMITY 14

EN 4
A - SAFETY INSTRUCTIONS
1 - OPERATING PRECAUTIONS
• Read this entire manual before starting the
installation.
• Do not allow children to operate the product.
• This product is designed exclusively for indoor
use.
• This product is designed to work on a
smartphone with WIFI.
2 - DESCRIPTION
This product is a 3V DC photoelectric smoke
detector. It works with two AA alkaline batteries.
The photoelectric technology makes the smoke
detector more sensitive to the detection of slow-
smouldering res which generally produce thick,
black smoke, little heat and can smoulder for
hours before bursting into ames.
The smoke detector can be installed in every room
(except the bathroom), making sure that the alarm
signal can be heard by everyone in the house. For
minimum protection, you should install the smoke
detector in the hallway between living spaces and
sleeping areas.
Place the smoke detector as close as possible
to living rooms and make sure the alarm can be
heard from the bedrooms.
• Typical single-storey dwelling with recommended
protection:
Install a smoke detector on the ceiling of each
room and in the hallway outside each separate
sleeping area. If a hallway is more than 10 m
long, install a smoke detector at each end. If
there is a basement: install a smoke detector on
the ceiling of the basement and at the bottom of
the stairwell.
• Typical multi-storey dwelling with recommended
protection:
Install a smoke detector on the ceiling of each
room and in the hallway outside each separate
sleeping area. If a hallway is more than 10 m
long, install a smoke detector at each end.
Install a smoke detector at the top of the
stairwell and on each oor.
3 - IMPORTANT SAFETY INFORMATION
Important safety information:
1: The test button accurately tests the functions of
the smoke detector. Do not use any other test
method. Test the smoke detector once a week
to make sure it is working properly.
2: Do not remove or disconnect the battery. This
would remove your protection.
3: Observe and follow all electrical instructions in
the building code for installation.
4: This smoke detector is designed for indoor use
only. In buildings, each apartment must have its
own smoke detector.
5: Install a smoke detector in each room and on
each oor of the house. Smoke may not reach
the smoke detector for many reasons. For
example, if a re breaks out in a remote part
of the house, on another level, in a chimney,
wall, roof or on the other side of a closed door.
A smoke detector cannot detect a re quickly,
except in the area or room where it is installed.
6: There may be circumstances where a household
member may not hear the alarm (too much
noise outside or inside, use of drugs or alcohol,
hearing-impaired, etc.). If you suspect that this
smoke detector may not alert a household
member, install specialised smoke detectors.
Note: if a household member is hard of
hearing, install special smoke detectors
with lights or vibrating devices to alert the
occupants.
7: Smoke detectors can only trigger their alarms
when they detect smoke or combustion particles
in the air. They do not detect heat, a ame or
gas leak. This smoke detector is designed to
alert you when a re breaks out. However, some
res are rapid, explosive or intentional, while
others are caused by negligence or safety risks.
In this context, smoke may not trigger the alarm
quickly enough to ensure a safe escape.
8: Smoke detectors have limitations. This smoke
detector is not foolproof and is not guaranteed
to protect lives or property
from re. Smoke alarms are not a substitute for
insurance.
Do not install smoke detectors in the following
locations:
1: Near appliances or areas where normal
combustion occurs regularly (kitchens, hot
water, radiators, etc.).
2: In very humid areas, such as bathrooms or
areas near dishwashers or washing machines.
WIFI-CONNECTED SMOKE DETECTOR

EN5
A - SAFETY INSTRUCTIONS
WIFI-CONNECTED SMOKE DETECTOR
Install the detector at least 3 m from these areas.
3: Near heating and cooling supply vents. Install at
least 3 m from these areas. The air could blow
smoke away from the detector, thus interrupting
its alarm.
4: In rooms where temperatures can drop below
0°C or rise above 40°C.
5: In extremely dusty, dirty or insect-infested areas,
particles interfere with the operation of the
smoke detector.
4 - MAINTENANCE AND CLEANING
The outer case can be cleaned periodically.
• Do not use abrasive substances, substances
containing alcohol, thinners or other ammable
substances.
• Do not spray any products directly onto the unit.
5 - RECYCLING
This logo denotes that devices no longer
in use should not be disposed of as
household waste. They are likely to
contain hazardous substances which are
dangerous to both health and the
environment. Return the equipment to your local
distributor or use the recycling collection service
provided by your local council.
Pour en savoir plus :
www.quefairedemesdechets.fr

EN 6
B - PRODUCT DESCRIPTION
1 - KIT CONTENTS
1x1
2 - SMART SMOKE DETECTOR
WIFI-CONNECTED SMOKE DETECTOR
1WIFI smoke detector
2AA battery (LR06) x2
3Self-adhesive double sided tape mount
4Screws
2x2 3x1 4x2
1Button
2Warning light
3Siren
4Air inlet for smoke detection
3
4
2
1

EN7
B - PRODUCT DESCRIPTION
3 - INSTALLATION AREA
WIFI-CONNECTED SMOKE DETECTOR
Area Yes No
Living room X
Dining room X
Kitchen
X
Bathroom / Toilet
X
Bedroom
X
Hallway
X
Attic
X
Basement
X
Garage
X
Boiler room
X
500 mm
1000 mm
( 20’’ )
500 mm
1000 mm
500 mm
1000 mm
( 20’’ )
500 mm
1000 mm
500 mm
1000 mm
( 20’’ )
500 mm
1000 mm
CEILING
BEST
HERE
NEVER
HERE
DO NOT
INSTALL
DO NOT INSTALL
VAULTED CEILING
ATTIC CEILING
ANYWHERE
IN THIS AREA
ANYWHERE
IN THIS
AREA
NOT IN
THIS AREA
NOT IN
THIS AREA
DEAD
SPACE DEAD
SPACE
DEAD SPACE
50 cm
MINIMUM

EN 8
C - INSTALLATION
1 - INSTALLING THE DETECTOR ON THE
WALL OR CEILING
2 - REPLACING THE BATTERIES
WIFI-CONNECTED SMOKE DETECTOR

EN9
F - OPERATION WITH THE APP
1 - INDICATOR LIGHT
Normal
operation
The LED indicator
flashes red
once every
40 seconds.
---
Smoke/heat
detection
The alarm sounds.
and the LED
indicator
flashes red
without stopping
until smoke has
been evacuated
Evacuate smoke
or heat.
Low battery
alert
The alarm beeps
briefly every
40 seconds and
the LED indicator
flashes.
Do one of
the following:
• Replace the
battery.
• Press the
test button to
pause the alarm
for 8 hours.
Failure
The alarm beeps
briefly every
40 seconds.
Replace
the device.
Alarm test
The alarm must be tested once a week to make
sure it is working correctly. If the alarm test fails,
replace the batteries and/or the smoke detector.
- Press and hold the test button for 5 seconds.
The alarm sounds.
- Release the test button.
Mute function
If the alarm sounds in error while cooking, it can
be paused for 10 minutes by pressing the test
button. The LED indicator ashes once every 8
seconds. Locate the alarm source before using
the mute function to make sure it is not a life-
threatening situation.
2 - CONNECTION
2.1 - INSTALLING THE MOBILE APP AND
CREATING AN ACCOUNT
This product only works with a 2.4Ghz frequency.
During pairing, make sure your smartphone is
connected on that specic frequency. If you are
not sure, check with your Internet service provider.
Once the smoke detector has been installed,
follow the instructions below to pair it.
Download the Avidsen Home app from the
Android Play Store or Apple App Store.
Launch the app and log in if you already have
an account. If not, press CREER UN NOUVEAU
COMPTE (CREATE A NEW ACCOUNT) and let the
application guide you.
WIFI-CONNECTED SMOKE DETECTOR

EN 10
After accepting the privacy policy, create an
account with an email address.
In both cases, choose your country and, after
entering your email address, select Obtenir le
code de vérification (Get verification code).
In a few seconds, you will receive a conrmation
code in your email inbox. Enter this code to
nalise registration.
Note that this email may go into your spam folder.
If you do not receive a code before the countdown
has ended, press renvoyer (return) and check the
email address entered.
To complete your registration, set a password
between 6 and 20 characters long with letters and
numbers only, then press Terminé (Finished).
2.2 - CONNECTING THE SMOKE DETECTOR
Press the button 3 times in less than 2 seconds
to put the product in pairing mode. The indicator
light will start ashing until the pairing procedure is
completed. If it doesn't, follow the reset procedure
on your phone.
To start pairing, press AJOUTER (ADD). Make
sure your phone is connected to your router’s 2.4
GHz WiFi network. If you already have a device
installed on the application (e.g. IP camera, smart
plug, etc.) click on + in the top right corner of the
application.
Select the product you wish to pair, select the
smoke detector.
F - OPERATION WITH THE APP
WIFI-CONNECTED SMOKE DETECTOR

EN11
F - OPERATION WITH THE APP
Make sure the smoke detector is on and the red
indicator light is ashing. If not, press the central
button 3 times in succession so that the red
indicator light starts ashing.
Select your 2.4 GHz WiFi network (note: your
smartphone must be connected to the WiFi
network to which the plug will be connected),
enter your network password and press Suivant
(Next).
IMPORTANT: If a location authorisation request
message appears, you need to accept it for your
Android or iOS device to receive your WiFi.
IMPORTANT: This device is compatible with 2.4
GHz - WPA/WPA2 networks. Not compatible
with 5 GHz WiFi or with WEP encryption. Please
check the WiFi settings of your router or contact
your Internet service provider if you experience
connection difculties.
If this message appears
Click on Changement (Change) or simply connect
your smartphone to the 2.4GHz frequency and
then click on Continuer (Continue).
Please wait while the pairing procedure takes
place. This can take a few minutes.
WIFI-CONNECTED SMOKE DETECTOR

EN 12
F - OPERATION WITH THE APP
WIFI-CONNECTED SMOKE DETECTOR
Your smoke detector is now operational and will
appear in your app. You can now control your
Avidsen sensor from your smartphone. You can
rename it by clicking on the small pencil to the right
of the device name.

EN13
1 - USE VIA THE APPLICATION
This smoke detector helps detect a re outbreak
in your house. You can receive notications on
your smartphone and use this detector with other
products to set up automation (see scenario tab).
For example, you can switch on the HomeLight
bulb automatically for a few minutes when the
smoke detector detects smoke.
E - USE
F - TECHNICAL AND LEGAL INFORMATION
1 - TECHNICAL CHARACTERISTICS
Features WiFi smoke detector
Connection Wireless - WiFi
Use Indoor
Consumption < 6uA (standby), < 1,200mA (alarm)
Alarm > 85dB(A) at a distance of 3 metres, > 90dB(A) at a distance of 1
metre
Smoke detection sensitivity: 0.108-0.141dB/m
Temperature detection sensitivity: 54-70°C
Noise emission when smoke is detected: BI 0.5s - pause 0.5s – BI 0.5s – pause 0.5s – BI 0.5s –
pause 1.5s, the red LED ashes, this sequence is repeated.
noise emission when temperature is
detected:
BI 0.2s - pause 0.1s, the red LED ashes, this sequence is
repeated.
Max EIRP 20 dB/m
Operating T° 0°C/+40°C
Storage T° -10°C/+50°C
Battery 2 x 1.5V AA Alkaline
Installation On a wall or on the ceiling
Colour White
Protection rating IP20
Radio protocol WiFi
Radio frequency 2.4 GHz
Protocol 802.11 b/g/n
Radio range
- Unobstructed range: 50m
- Masonry: 25m, through 3 walls max.
- Reinforced concrete: 10 m, through 1 wall/oor max.
- Plasterboard/Wood: 30 m, through 5 walls max.
WIFI-CONNECTED SMOKE DETECTOR

EN 14
F - TECHNICAL AND LEGAL INFORMATION
2 - WARRANTY
This product is guaranteed for parts and labour
for 2 years from the date of purchase. Proof of
purchase must be retained for the duration of the
warranty period.
The warranty does not cover damage caused by
knocks or accidents.
3 - HELP AND ADVICE
• If, despite the care we have taken in designing
our products and drafting these instructions,
you encounter difculties when installing your
product or you have any questions, we strongly
recommend that you contact one of our specialists
who will be glad to help.
• If you encounter operating problems during
installation or a few days afterwards, it is essential
for you to be in front of your installation when
contacting us, so that one of our technicians can
diagnose the source of the problem, as it will
probably be the result of a setting that is incorrect
or an installation that is not to specication. If
the problem is caused by the product itself, the
technician will give you an RMA number so that
you can return the unit to the shop.
Without this RMA number, the shop may refuse to
exchange your product.
Need advice for the installation or start-up of your
product?
Contact our after-sales service team technicians:
0,35 € / min
0 892 701 369
Monday to Friday, 9am to 12pm, and 2pm to
6pm.
Avidsen undertakes to keep a stock of spare
parts for this product throughout the contractual
warranty period.
4 - EU DECLARATION OF CONFORMITY
Avidsen declares, under its sole responsibility,
that the equipment with reference number 127065
complies with the applicable Union harmonisation
legislation 2014/53/EU. Its conformity has been
assessed pursuant to the applicable standards in
force:
EMC Directive 2014/30/EU
EN301489-1 V2.2.3
EN301489-17 V3.2.4
RED Directive 2014/53/EU
EN300328 V2.2.2
LVD Directive 2014/35/EU
EN62311:2010
Directive 89/106/EEC
EN14604:2005
EN14604:2005/AC:2008
Signed by Alexandre Chaverot, CEO, on behalf of
Avidsen
19 avenue Marcel Dassault, 37200 Tours, France
Tours, 12/07/2022
WIFI-CONNECTED SMOKE DETECTOR

Avidsen
19 avenue Marcel Dassault - ZAC des Deux Lions
37200 Tours - France