Avtech AVR-E3-B User manual

INSTRUCTIONS
MODEL AVR-E3-B
100 VOLTS, 500 ps RISE TIME
HIGH PERFORMANCE PULSE GENERATOR
WITH IEEE 488 2 AND RS-232 CONTROL
SERIAL NUMBER: ____________
A V T E C H E L E C T R O S Y S T E M S L T D .
N A N O S E C O N D W A V E F O R M E L E C T R O N I C S
S I N C E 1 9 7 5
P O BOX 265
OGDENSBURG, NY
U S A 13669-0265
TEL: [phone] (USA & Canada) or [phone] (Intl)
FAX: [phone] (USA & Canada) or [phone] (Intl)
info@avtechpulse com - http://www avtechpulse com/
X
BOX 5120, LCD MERIVALE
OTTAWA, ONTARIO
CANADA K2C 3H5

WARRANTY
Avtech Electrosystems Ltd warrants products of its manufacture to be free from
defects in material and workmanship under conditions of normal use If, within
one year after delivery to the original owner, and after prepaid return by the
original owner, this Avtech product is found to be defective, Avtech shall at its
option repair or replace said defective item This warranty does not apply to
units which have been dissembled, modified or subjected to conditions
exceeding the applicable specifications or ratings This warranty is the extent of
the obligation assumed by Avtech with respect to this product and no other
warranty or guarantee is either expressed or implied
TECHNICAL SUPPORT
Phone: [phone] (USA & Canada) or [phone] (International)
Fax: [phone] (USA & Canada) or [phone] (International)
E-mail: info@avtechpulse com
World Wide Web: http://www avtechpulse com
2

TABLE OF CONTENTS
WARRANTY......................................................................................................................2
TECHNICAL SUPPORT....................................................................................................2
TABLE OF CONTENTS....................................................................................................3
INTRODUCTION...............................................................................................................6
AVAILABLE OPTIONS......................................................................................................7
SPECIFICATIONS.............................................................................................................8
REGULATORY NOTES.....................................................................................................9
FCC PART 18..........................................................................................................................9
EC DECLARATION OF CONFORMITY...................................................................................9
DIRECTIVE 2011/65/EU (RoHS)...........................................................................................10
DIRECTIVE 2002/96/EC ( EEE)..........................................................................................10
AC PO ER SUPPLY REGULATORY NOTES......................................................................11
FIRM ARE LICENSING........................................................................................................11
INSTALLATION...............................................................................................................13
VISUAL CHECK....................................................................................................................13
PO ER RATINGS.................................................................................................................13
CONNECTION TO THE PO ER SUPPLY............................................................................13
PROTECTION FROM ELECTRIC SHOCK...........................................................................14
ENVIRONMENTAL CONDITIONS.........................................................................................15
LABVIE DRIVERS..............................................................................................................15
FUSES.............................................................................................................................16
AC FUSE REPLACEMENT...................................................................................................16
DC FUSE REPLACEMENT...................................................................................................17
FUSE RATINGS..................................................................................................................... 17
FRONT PANEL CONTROLS..........................................................................................18
REAR PANEL CONTROLS............................................................................................20
GENERAL INFORMATION.............................................................................................22
BASIC PULSE CONTROL....................................................................................................22
TRIGGER MODES................................................................................................................23
GATING MODES...................................................................................................................24
OPTIONAL FEATURES..................................................................................................2
RACK MOUNTING, -R5 OPTION..........................................................................................25
3

DC OFFSET, -OS OPTION....................................................................................................25
ELECTRONIC AMPLITUDE CONTROL, -EA OPTION.........................................................25
PROTECTING YOUR INSTRUMENT.............................................................................26
TURN OFF INSTRUMENT HEN NOT IN USE....................................................................26
DO NOT EXCEED 100 kHz (20 kHz FOR - 2 & - 3 UNITS).............................................26
USE A 50Ω LOAD.................................................................................................................26
OPERATIONAL CHECK.................................................................................................27
PROGRAMMING YOUR PULSE GENERATOR............................................................31
KEY PROGRAMMING COMMANDS.....................................................................................31
ALL PROGRAMMING COMMANDS......................................................................................32
MECHANICAL INFORMATION......................................................................................34
TOP COVER REMOVAL.......................................................................................................34
RACK MOUNTING................................................................................................................ 34
ELECTROMAGNETIC INTERFERENCE..............................................................................34
MAINTENANCE..............................................................................................................3
REGULAR MAINTENANCE...................................................................................................35
CLEANING............................................................................................................................ 35
TRIGGER DAMAGE.............................................................................................................. 35
WIRING DIAGRAMS.......................................................................................................36
IRING OF AC PO ER.......................................................................................................36
PCB 158Q - LO VOLTAGE PO ER SUPPLY, 1/3............................................................37
PCB 158Q - LO VOLTAGE PO ER SUPPLY, 2/3............................................................38
PCB 158Q - LO VOLTAGE PO ER SUPPLY, 3/3............................................................39
PCB 168 - HIGH VOLTAGE DC PO ER SUPPLY...............................................................40
PCB 235B - HIGH VOLTAGE DC PO ER SUPPLY.............................................................41
PCB 282A - HIGH VOLTAGE DC PO ER SUPPLY.............................................................42
PCB 244A - OCTAL RELAY DRIVER BOARD......................................................................43
PCB 151C - RANGE / POLARITY RELAY BOARD...............................................................44
PCB 104F - KEYPAD / DISPLAY BOARD, 1/3......................................................................45
PCB 104F - KEYPAD / DISPLAY BOARD, 2/3......................................................................46
PCB 104F - KEYPAD / DISPLAY BOARD, 3/3......................................................................47
MAIN IRING, STANDARD MODELS..................................................................................48
MAIN IRING, - 1 MODELS...............................................................................................49
MAIN IRING, - 2 MODELS...............................................................................................50
PO ER SUPPLY, - 2 AND - 3 MODELS..........................................................................51
4

MAIN IRING, - 3 MODELS (2 OF 2).................................................................................52
MAIN IRING, AVR-E3-B-PN- 1-OT13-ATT-AK2-AC02.....................................................53
PERFORMANCE CHECKSHEET................................................................................... 4
Manual Reference: /fileserver2/officefiles/instructword/avr-e/AVR-E3-B,ed10 odt
Last modified July 28, 2016
Copyright © 2016 Avtech Electrosystems Ltd, All Rights Reserved
5

INTRODUCTION
The AVR-E3-B is a high performance, GPIB and RS232-equipped instrument capable
of generating up to 100V into 50Ω loads The rise time (20%-80%) is less than 500 ps,
and the fall time (80%-20%) is less than 1 ns
On standard models, the output pulse width is variable from 10 ns to 200 ns, at
repetition rates up to 100 kHz
Models with the -W1 option have an output pulse width variable from 1 ns to 200 ns, at
repetition rates up to 100 kHz
Models with the -W2 option have an output pulse width variable from 50 ns to 5 us, at
repetition rates up to 20 kHz
Models with the -W3 option have an output pulse width variable from 1 ns to 5 us, at
repetition rates up to 20 kHz
Instruments with the "-P" model suffix can generate up to +100V, whereas instruments
with the "-N" model suffix can generate up to -100V Instruments with the "-PN" suffix
can generate both polarities
A 50 Ohm load is required for proper operation The output stage may be damaged if
the output is not terminated into a 50Ω load
The AVR-E3-B is a highly flexible instrument Aside from the internal trigger source, it
can also be triggered or gated by external TTL-level signals A front-panel pushbutton
or a computer command can also be used to trigger the instrument
The AVR-E3-B features front panel keyboard and adjust knob control of the output
pulse parameters along with a four line by 40-character backlit LCD display of the
output amplitude, pulse width, pulse repetition frequency, and delay The instrument
includes memory to store up to four complete instrument setups The operator may use
the front panel or the computer interface to store a complete “snapshot” of all key
instrument settings, and recall this setup at a later time
This instrument is intended for use in research, development, test and calibration
laboratories by qualified personnel
6

AVAILABLE OPTIONS
The AVR-E3-B is available with several options, including:
-ATT Option: Adds internal relay-switched 10 dB and 20 dB attenuators to provide
improved low-amplitude performance The attenuators are automatically enabled based
on the programmed amplitude, and can handle the full output power of the instrument
The attenuators only act on the pulse amplitude (the offset bias tee is after the
attenuator circuit)
-EA Option: the amplitude can be controlled by an externally generated 0 to +10V
analog control voltage
-OS Option: an externally generated DC offset can be added to the output
-OT13 Option: Adds an internally-generated and programmable -13V to +13V DC offset
source (260 mA maximum current) The resolution is ~4 mV
-R5 Option: This is the optional rack-mounting kit The R5 rack-mount kit may also be
ordered separately
-VXI Option: Adds a rear-panel Ethernet connector, allowing the instrument to be
remotely controlled using the VXI-11 3, ssh (secure shell), telnet, and http (web)
protocols In particular, the VXI-11 3 features allows software like LabView to control an
instrument using standard VISA communications drivers and network cabling, instead
of using old-style GPIB cabling (This eliminates the need for a GPIB controller card
and its proprietary drivers )
7

SPECIFICATIONS
Model: AVR-E3-B2
Maximum amplitude3: (50Ω load8) 100V
Rise time (20%-80%): ≤ 0 5 ns
Fall time (80%-20%): ≤ 1 0 ns
Pulse width (FWHM): standard units: 10 ns to 200 ns
with -W1 option: 1 ns to 200 ns
with -W2 option: 50 ns to 5 us
with -W3 option: 1 ns to 5 us
Maximum PRF:
Standard units, or with -W1 option:
Units with -W2 or -W3 options:
100 kHz
20 kHz
Maximum duty cycle: 5%
Polarity: Positive or negative or both (specify4)
DC offset or bias insertion: Option available5 Apply required DC offset or bias in the range of ± 25 Volts,
(250 mA max) to back panel solder terminals
Trigger modes: Internal trigger, external trigger (TTL level pulse, > 10 ns, 1 kΩ input impedance),
front-panel “Single Pulse” pushbutton, or single pulse trigger via computer command
Variable delay: 0 to 1 0 seconds, for all trigger modes (including external trigger)
Propagation delay: ≤ 160 ns (Ext trig in to pulse out)
Jitter: (Ext trig in to pulse out) ± 35ps ± 0 015% of sync delay
Sync output: > +3 Volts, > 50 ns, will drive 50 Ohm loads
Gate input: Synchronous or asynchronous, active high or low, switchable Suppresses triggering when active
Connectors: Out: SMA, Other: BNC
Power requirements: 100 - 240 Volts, 50 - 60 Hz
GPIB and RS-232 control2: Standard on -B units
LabView drivers: Check http://www avtechpulse com/labview for availability and downloads
Ethernet port, for remote control
using VXI-11 3, ssh, telnet, & web:
Optional6 Recommended as a modern alternative to GPIB / RS-232
See http://www avtechpulse com/options/vxi for details
Settings resolution: The resolution of the timing parameters (pulse width, delay, period) varies,
but is always better than 0 15% of (|set value| + 20 ns)
The amplitude resolution is < 0 1% of the maximum amplitude
Settings accuracy: Typically ± 3% (±2 ns or ± 2% of max amplitude) after 10 minute warmup For high-accuracy
applications requiring traceable calibration, verify the output with a calibrated oscilloscope
Dimensions (H x W x D): 100 mm x 430 mm x 375 mm (3 9” x 17” x 14 8”)
Chassis material: cast aluminum frame and handles, blue vinyl on aluminum cover plates
Temperature range: +5°C to +40°C
1) -C suffix indicates stand-alone lab instrument with internal clock and line powering (See http://www avtechpulse com/formats for additional details of
the four basic instrument formats)
2) -B suffix indicates IEEE-488 2 GPIB and RS-232 control of amplitude, pulse width, PRF and delay (see http://www avtechpulse com/gpib)
3) For operation at amplitudes of less than 10% of full-scale, best results will
be obtained by setting the amplitude near full-scale and using external attenuators on the output
4) Indicate desired polarity by suffixing model number with -P or -N (i e positive or negative) or -PN for dual polarity option Polarity reversal achieved
by means of a two-position switch that controls the polarity of the signal output port on -C units, and via keypad control on -B units -PN option not
available on -W3 units
5) For DC offset option suffix model number with -OS
6) Add the suffix -VXI to the model number to specify the Ethernet port
7) Fall time increases to < 3 ns for pulse widths less than 15 ns
8) A 50Ω load is required Other loads may damage the instrument Consult Avtech (info@avtechpulse com) if you need to drive other
load impedances
8

REGULATORY NOTES
FCC PART 18
This device complies with part 18 of the FCC rules for non-consumer industrial,
scientific and medical (ISM) equipment
This instrument is enclosed in a rugged metal chassis and uses a filtered power entry
module (where applicable) The main output signal is provided on a shielded connector
that is intended to be used with shielded coaxial cabling and a shielded load Under
these conditions, the interference potential of this instrument is low
If interference is observed, check that appropriate well-shielded cabling is used on the
output connectors Contact Avtech (info@avtechpulse com) for advice if you are unsure
of the most appropriate cabling Also, check that your load is adequately shielded It
may be necessary to enclose the load in a metal enclosure
If any of the connectors on the instrument are unused, they should be covered with
shielded metal “dust caps” to reduce the interference potential
This instrument does not normally require regular maintenance to minimize interference
potential However, if loose hardware or connectors are noted, they should be
tightened Contact Avtech (info@avtechpulse com) if you require assistance
EC DECLARATION OF CONFORMITY
We Avtech Electrosystems Ltd
P O Box 5120, LCD Merivale
Ottawa, Ontario
Canada K2C 3H5
declare that this pulse generator meets the intent of Directive 2004/108/EG for
Electromagnetic Compatibility Compliance pertains to the following specifications as
listed in the official Journal of the European Communities:
EN 50081-1 Emission
EN 50082-1 Immunity
9

and that this pulse generator meets the intent of the Low Voltage Directive 2006/95/EC
Compliance pertains to the following specifications as listed in the official Journal of the
European Communities:
EN 61010-1:2001 Safety requirements for electrical equipment for
measurement, control, and laboratory use
DIRECTIVE 2011/65/EU (RoHS)
We Avtech Electrosystems Ltd
P O Box 5120, LCD Merivale
Ottawa, Ontario
Canada K2C 3H5
declare that, to the best of our knowledge, all electrical and electronic equipment (EEE)
sold by the company are in compliance with Directive 2011/65/EU of the European
Parliament and of the Council of 8 June 2011 on the restriction of the use of certain
hazardous substances in electrical and electronic equipment (also known as “RoHS
Recast”) In addition, this declaration of conformity is issued under the sole
responsibility of Avtech Electrosystems Ltd Specifically, products manufactured do not
contain the substances listed in the table below in concentrations greater than the
listed maximum value
Material/Substance Threshold level
Lead (Pb) < 1000 ppm (0 1% by mass)
Mercury (Hg) < 1000 ppm (0 1% by mass)
Hexavalent Chromium (Cr6+) < 1000 ppm (0 1% by mass)
Polybrominated Biphenyls (PBB) < 1000 ppm (0 1% by mass)
Polybrominated Diphenyl ethers (PBDE) < 1000 ppm (0 1% by mass)
Cadmium (Cd) < 100 ppm (0 01% by mass)
DIRECTIVE 2002/96/EC (WEEE)
European customers who have purchased this equipment directly from Avtech will have
completed a “WEEE Responsibility Agreement” form, accepting responsibility for
WEEE compliance (as mandated in Directive 2002/96/EC of the European Union and
local laws) on behalf of the customer, as provided for under Article 9 of Directive
2002/96/EC
Customers who have purchased Avtech equipment through local representatives
should consult with the representative to determine who has responsibility for WEEE
10

compliance Normally, such responsibilities with lie with the representative, unless
other arrangements (under Article 9) have been made
Requirements for WEEE compliance may include registration of products with local
governments, reporting of recycling activities to local governments, and financing of
recycling activities
AC POWER SUPPLY REGULATORY NOTES
This instrument converts the AC input power to the +24V DC voltage that powers the
internal circuitry of this instrument using a Tamura AAD130SD-60-A switching power
supply According to the manufacturer, the Tamura AAD130SD-60-A has the following
certifications:
UL60950-1
IEC60950 -1
CSA C22 2 No 60950- 1
EN60950 -1
and is compliant with:
EN61000-3-2
EN61000-4-2 Level 2
EN61000-4-2 Level 3 (Air Only)
EN61000-4-4 Level 3
EN61000-4-5 Level 3
EN61000-4-11
CISPR 11 and 22 FCC Part 15 Class B (conducted)
FIRMWARE LICENSING
Instruments with firmware versions 5 00 or higher use open-source software internally
Some of this software requires that the source code be made available to the user as a
condition of its licensing This source code is available upon request (contact
info@avtechpulse com)
11

Earlier firmware versions do not contain any open source software
12

INSTALLATION
VISUAL CHECK
After unpacking the instrument, examine to ensure that it has not been damaged in
shipment Visually inspect all connectors, knobs, liquid crystal displays (LCDs), and the
handles Confirm that a power cord, a GPIB cable, and two instrumentation manuals
(this manual and the “Programming Manual for -B Instruments”) are with the instrument
If the instrument has been damaged, file a claim immediately with the company that
transported the instrument
POWER RATINGS
This instrument is intended to operate from 100 - 240 V, 50 - 60 Hz
The maximum power consumption is 90 Watts Please see the “FUSES” section for
information about the appropriate AC and DC fuses
This instrument is an “Installation Category II” instrument, intended for operation from a
normal single-phase supply
CONNECTION TO THE POWER SUPPLY
An IEC-320 three-pronged recessed male socket is provided on the back panel for AC
power connection to the instrument One end of the detachable power cord that is
supplied with the instrument plugs into this socket The other end of the detachable
power cord plugs into the local mains supply Use only the cable supplied with the
instrument The mains supply must be earthed, and the cord used to connect the
instrument to the mains supply must provide an earth connection (The supplied cord
does this )
Warning: Failure to use a grounded outlet may result in injury or death due to
electric shock This product uses a power cord with a ground connection It must be
connected to a properly grounded outlet The instrument chassis is connected to the
ground wire in the power cord
The table below describes the power cord that is normally supplied with this instrument,
depending on the destination region:
13

Destination Region Description Option Manufacturer Part Number
United Kingdom, Hong Kong,
Singapore, Malaysia
BS 1363,
230V, 50 Hz -AC00 Qualtek 370001-E01
Australia, New Zealand AS 3112:2000,
230-240V, 50 Hz -AC01 Qualtek 374003-A01
Continental Europe, Korea,
Indonesia, Russia
European CEE 7/7
“Schuko” 230V, 50 Hz -AC02 Qualtek 364002-D01
North America, Taiwan NEMA 5-15,
120V, 60 Hz -AC03 Qualtek 312007-01
Switzerland SEV 1011,
230V, 50 Hz -AC06 Qualtek 378001-E01
South Africa, India SABS 164-1,
220-250V, 50 Hz -AC17 Volex 2131H 10 C3
Japan JIS 8303,
100V, 50-60 Hz -AC18 Qualtek 397002-01
Israel SI 32,
220V, 50 Hz -AC19 Qualtek 398001-01
China GB 1002-1,
220V, 50 Hz -AC22 Volex 2137H 10 C3
PROTECTION FROM ELECTRIC SHOCK
Operators of this instrument must be protected from electric shock at all times The
owner must ensure that operators are prevented access and/or are insulated from
every connection point In some cases, connections must be exposed to potential
human contact Operators must be trained to protect themselves from the risk of
electric shock This instrument is intended for use by qualified personnel who recognize
shock hazards and are familiar with safety precautions required to avoid possibly injury
In particular, operators should:
1 Keep exposed high-voltage wiring to an absolute minimum
2 Wherever possible, use shielded connectors and cabling
3 Connect and disconnect loads and cables only when the instrument is turned off
4 Keep in mind that all cables, connectors, oscilloscope probes, and loads must
have an appropriate voltage rating
5 Do not attempt any repairs on the instrument, beyond the fuse replacement
procedures described in this manual Contact Avtech technical support (see
page 2 for contact information) if the instrument requires servicing Service is to
be performed solely by qualified service personnel
14

ENVIRONMENTAL CONDITIONS
This instrument is intended for use under the following conditions:
1 indoor use;
2 altitude up to 2 000 m;
3 temperature 5 °C to 40 °C;
4 maximum relative humidity 80 % for temperatures up to 31 °C decreasing
linearly to 50 % relative humidity at 40 °C;
5 Mains supply voltage fluctuations up to ±10 % of the nominal voltage;
6 no pollution or only dry, non-conductive pollution
LABVIEW DRIVERS
A LabVIEW driver for this instrument is available for download on the Avtech web site,
at http://www avtechpulse com/labview A copy is also available in National Instruments'
Instrument Driver Library at http://www natinst com/
15

FUSES
This instrument contains four fuses All are accessible from the rear-panel Two protect
the AC prime power input, and two protect the internal DC power supplies The
locations of the fuses on the rear panel are shown in the figure below:
AC FUSE REPLACEMENT
To physically access the AC fuses, the power cord must be detached from the rear
panel of the instrument The fuse drawer may then be extracted using a small flat-head
screwdriver, as shown below:
Fuses #1 and #2
(AC fuses)
Fuse #4
( C fuse)
Fuse #3
( C fuse)
Fuse
rawer
Pry out the fuse
drawer using a
screwdriver.
16

DC FUSE REPLACEMENT
The DC fuses may be replaced by inserting the tip of a flat-head screwdriver into the
fuse holder slot, and rotating the slot counter-clockwise The fuse and its carrier will
then pop out
FUSE RATINGS
The following table lists the required fuses for standard models:
Fuses
Nominal
Mains
Voltage
Rating Case Size
Recommended Replacement Part
Littelfuse Part
Number
Digi-Key Stock
Number
#1, #2 (AC)
115 V 0 8A, 250V,
Time-Delay 5×20 mm 0218 800HXP F2418-ND
230 V 0 5A, 250V,
Time-Delay 5×20 mm 0218 500HXP F2416-ND
#3 (DC) N/A 2 5A, 250V,
Time-Delay 5×20 mm 021802 5HXP F2427-ND
#4 (DC) N/A 0 8A, 250V,
Time-Delay 5×20 mm 0218 800HXP F2418-ND
Units with the -W2 or -W3 options have slightly different fuse requirements:
Fuses
Nominal
Mains
Voltage
Rating Case Size
Recommended Replacement Part
Littelfuse Part
Number
Digi-Key Stock
Number
#1, #2 (AC)
115 V 0 8A, 250V,
Time-Delay 5×20 mm 0218 800HXP F2418-ND
230 V 0 5A, 250V,
Time-Delay 5×20 mm 0218 500HXP F2416-ND
#3 (DC) N/A 2 5A, 250V,
Time-Delay 5×20 mm 021802 5HXP F2427-ND
#4 (DC) N/A 1 6A, 250V,
Time-Delay 5×20 mm 021801 6HXP F2424-ND
The recommended fuse manufacturer is Littelfuse (http://www littelfuse com)
Replacement fuses may be easily obtained from Digi-Key (http://www digikey com) and
other distributors
17

FRONT PANEL CONTROLS
1 POWER Switch This is the main power switch When turning the instrument on,
there is normally a delay of 10 seconds before anything is shown on the main
display, as the internal operating system boots up
If the main menu does not appear after 30 seconds, turn off the instrument and
leave it off for at least 60 seconds before applying power again
2 OVERLOAD Indicator When the instrument is powered, this indicator is normally
green, indicating normal operation If this indicator is yellow, an internal automatic
overload protection circuit has been tripped If the unit is overloaded (by operating
at an exceedingly high duty cycle or by operating into a very low impedance), the
protective circuit will disable the output of the instrument and turn the indicator light
yellow The light will stay yellow (i e output disabled) for about 5 seconds after
which the instrument will attempt to re-enable the output (i e light green) for about 1
second If the overload condition persists, the output will be disabled again (i e light
yellow) for another 5 seconds If the overload condition has been removed, the
instrument will resume normal operation
This overload indicator may flash yellow briefly at start-up This is not a cause for
concern
3 OUT CONNECTOR This SMA connector provides the main output signal, into load
impedances of 50Ω
4 SYNC OUT This connector supplies a SYNC output that can be used to trigger
other equipment, particularly oscilloscopes This signal leads (or lags) the main
output by a duration set by the "DELAY" controls and has an approximate amplitude
of +3 Volts to RL > 50Ω with a pulse width of approximately 100 ns
5 LIQUID CRYSTAL DISPLAY (LCD) This LCD is used in conjunction with the keypad
to change the instrument settings Normally, the main menu is displayed, which lists
the key adjustable parameters and their current values The “Programming Manual
24
5
18
3
6
1

for -B Instruments” describes the menus and submenus in detail
6 KEYPAD
Control Name Function
MOVE This moves the arrow pointer on the display
CHANGE This is used to enter the submenu, or to select the operating
mode, pointed to by the arrow pointer
×10 If one of the adjustable numeric parameters is displayed, this
increases the setting by a factor of ten
÷10 If one of the adjustable numeric parameters is displayed, this
decreases the setting by a factor of ten
+/- If one of the adjustable numeric parameters is displayed, and
this parameter can be both positive or negative, this changes
the sign of the parameter
EXTRA FINE This changes the step size of the ADJUST knob In the extra-
fine mode, the step size is twenty times finer than in the normal
mode This button switches between the two step sizes
ADJUST This large knob adjusts the value of any displayed numeric
adjustable values, such as frequency, pulse width, etc The
adjust step size is set by the "EXTRA FINE" button
When the main menu is displayed, this knob can be used to
move the arrow pointer
19

REAR PANEL CONTROLS
Note: some connectors may be in different positions than shown above, depending on
the exact combination of options ordered.
1 AC POWER INPUT An IEC-320 C14 three-pronged recessed male socket is
provided on the back panel for AC power connection to the instrument One end of
the detachable power cord that is supplied with the instrument plugs into this
socket
2 AC FUSE DRAWER The two fuses that protect the AC input are located in this
drawer Please see the “FUSES” section of this manual for more information
3 DC FUSES These two fuses protect the internal DC power supplies Please see the
“FUSES” sections of this manual for more information
4 GATE This TTL-level (0 and +5V) logic input can be used to gate the triggering of
the instrument This input can be either active high or active low, depending on the
front panel settings or programming commands (The instrument triggers normally
when this input is unconnected) When set to active high mode, this input is pulled-
down to ground by a 1 kΩ resistor When set to active low mode, this input is pulled-
up to +5V by a 1 kΩ resistor
5 TRIG This TTL-level (0 and +5V) logic input can be used to trigger the instrument, if
the instrument is set to triggering externally The instrument triggers on the rising
edge of this input The input impedance of this input is 1 kΩ (Depending on the
length of cable attached to this input, and the source driving it, it may be desirable
to add a coaxial 50 Ohm terminator to this input to provide a proper transmission
line termination The Pasternack (www pasternack com) PE6008-50 BNC feed-thru
50 Ohm terminator is suggested for this purpose )
20
7
9, 10
2
3
6
1
48
5
GATE
TRIG RS-232
GPIB
AMP