Avtech 960H User manual

544Z
151_V0.9
REGULAR CAMERA USER MANUAL
960H Ultra Resolution Series
It’s recommended to use this camera with a DVR which supports 960H video recording.
Please read the instructions thoroughly before using the product.
FEATURES
1. 1/3" HR Color CCD
2. 700 TVL superior image quality
3. Further camera parameters configuration via its own OSD
4. Multilingual on-screen display menu in 4 languages (English / French / Portuguese / Spanish)
5. Built-in microphone for audio recording
PACKAGE CONTENT
‧ Camera x 1 ‧ User manual x 1 ‧ Wrench x 1
SPECIFICATION*
Pick up Element 1/3" HR color CCD image sensor
Number of Pixel 976(H) x 494(V) <NTSC> / 976(H) x 582(V) <PAL>
Resolution 700 TVL
Minimum Illumination 0.1 Lux / F2.0
S/N Ratio More than 48dB (AGC off)
Electronic Shutter AUTO: 1/50 (60) to 1/100,000 sec.
MANUAL: 1/50(60), FL 1/120(100), 1/250, 1/500, 1/1,000, 1/2,000,
1/5,000, 1/10,000, 1/20,000, 1/50,000, 1/100,000 sec.
Lens Mount CS Mount
IRIS Mode AES / VD / DD
White Balance Auto / Fixed
Gain Control AGC adjustable / Fixed
Sharpness Adjustable
BLC ON / OFF
Digital WDR YES
Video Output 1.0 Vp-p composite, 75Ω
Microphone Built-in
Power Source (±10%) DC 12V
Current Consumption(±10%) 70mA
Dimensions (mm)** 117(L) x 60(W) x 50(H)
* The specifications are subject to change without notice. ** Dimensional Tolerance: ± 5mm

MAJOR OPERATING CONTROL AND FUNCTIONS
1. Flange Back Adjusting Ring
It is suitable for CS-mount lens. When using C-mount lens, please use the CS-C conversion ring*.
2. Back Focal Lock Hexagonal Bolt
The camera is set at the standard back focal position. Fine-tuning is inevitable according to the lens types.
Adjust the lens back-focus by turning the focusing knob.
3. Auto Iris Lens Connector
Supplies power and controls signals to an Auto Iris Lens.
4. Power LED Indicator
The Power LED Indicator indicates normal status during operation.
5. Power Input Terminal !
For connecting to DC12V regulated power supply.
6. Video Output Connector (VIDEO OUT)
For connecting to CCTV monitor video input with coaxial cable.
7. V.D. / D.D. selectable
When using Auto Iris Lens, select Video Drive or Direct Drive depend on the type of lens you used.
8. Audio Output Connector (AUDIO OUT)
Connect to the AUDIO IN connector of the recording device.
9. OSD Menu Selection
For more details, please refer to “CAMERA PARAMETERS”.
INSTALLATION
*** It is recommended to have the following installation done by the qualified service personnel or system
installer. ***
1. Mount a lens onto the camera (By turning it clockwise).
It is suitable for CS-mount lens.
But if the lens you chose is C-mount, please use the CS-C conversion ring* to connect the C-mount lens
and the camera.
2. Switch the lens selection depending on the lens you used.
* Auto iris lens:
V.D. / D.D.: Select VD or DD depend on the type of lens you used.
3. Connect the camera VIDEO output and the monitor video input with a 75Ωcoaxial cable.
4. Connect the camera AUDIO output and the monitor audio input with a coaxial cable.
5. Connect the POWER terminal of the camera to a right power supply.
6. Adjust the focus or flange-back (Please refer to N NO OT TE E for adjustment instructions).
* The CS-C conversion ring is not supplied in the sales package and needs to be purchased separately.

Flange Back Adjusting Ring
Back focal lock hexa
g
onal bolt
NOTE: Focus or Flange-Back Ring Adjustment
1. Mount the lens
by turning it clockwise on the lens mount of the camera.
2. Loosen the screws on the flange-back adjusting ring.
3. Turn the flange-back adjusting ring to the desired position.
4. Tighten the screws on the flange-back adjusting ring.
PRECAUTIONS
Do not install the camera in an environment where the humidity or temperature is high
Do not install the camera under the unstable lighting condition
Do not expose the camera to rain or moisture
Do not keep the camera face to strong light directly
Do not touch the front glass of the camera
Do not use other than specified power source
Do not disassemble the camera
CAMERA PARAMETERS
There are five buttons on the camera rear panel for users to further configure camera parameters.
If you want to … Press …
Enter the camera configuration menu MENU
Move to the sub-menu you want ↑/ ↓
Change setting ←/ →
Enter the configuration page of an option ENTER
Menu Tree
For options with , press the button “ ” (Enter) to enter their respective setting pages.
SUB-MENU OPTIONS REMARK
LANGUAGE LANGUAGE ENGLISH / PORTUGUÊS / ESPAÑOL /
FRANCÊS
OSD COLOR WHITE / YELLOW / CYAN / GREEN /
MAGENTA / RED / BLUE / BLACK
CAMERA ID ID SET (POSITION) OFF / TOP / BOTTOM
ID NO
EXPOSURE LENS MANUAL / DC
BLC OFF / PAT 1 / PAT2
GAIN CONTROL AUTO-H / AUTO-M / AUTO-L /
-3 ~ 36dB
SHUTTER (1/N) AUTO / 60(50) / 100(120) / 250 / 500 /
1000 / 2000 / 5000 / 10000 / 20000 /
50000 / 100000
IMAGE BRIGHTNESS
CONTRAST
CHROMA GAIN
SHARPNESS
NOISE REDUCTION ON / OFF
WHITE BALANCE

SUB-MENU OPTIONS REMARK
FUNCTION MIRROR ON / OFF
FLICKERLESS ON / OFF
DAY NIGHT Not available
BLEMISH COMP
D-WDR ON / OFF
HLC ON / OFF
WINDOW Not available
PRIVACY MASK MASK NUMBER 1 ~ 8
MASK TYPE OFF / FULL / HALF
MASK SET
COLOR 1 ~ 8
MOTION DETECT MOTION DETECT Not available
ALERT (TIME)
SENSTIVITY
PIN OUTPUT
DISPLAY
COLOR
IGNORE AREA
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
This exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
ROHS Announcement
All lead-free products offered by the company comply with the requirements of the European law on the
Restriction of Hazardous Substances (RoHS) directive, which means our manufacture processes and
products are strictly “lead-free” and without the hazardous substances cited in the directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product must be collected
separately at the product end-of-life. This applies to your product and any peripherals marked with this
symbol. Do not dispose of these products as unsorted municipal waste.
CE Mark
This apparatus is manufactured to comply with the radio interference.
The company does not warrant that this manual will be uninterrupted or error-free. We reserve the right to
revise or remove any content in this manual at any time.
C
CA AU UT TI IO ON N: :
To reduce the risk of electric shock, do not expose this apparatus to rain or moisture.
Only operate this apparatus from the type of power source indicated on the label.
The company shall not be liable for any damages arising out of any improper use, even if we have been
advised of the possibility of such damages.
C
C
A
A
U
U
T
T
I
I
O
O
N
N
R
RI IS SK K O OF F E EL LE EC CT TR RI IC C S SH HO OC CK K