Avtech IC-AVM5547 User manual

m5547_d5606_2603svw_svs_2103sv_V1.1
IR BULLET
IP CAMERA SERIES
OPERATION GUIDE
Please read instructions thoroughly before operation and retain it for future reference.

IMPORTANT SAFEGUARD
All lead-free products offered by the company comply with the requirements of the
European law on the Restriction of Hazardous Substances (RoHS) directive, which means
our manufacture processes and products are strictly “lead-free” and without the hazardous
substances cited in the directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product
must be collected separately at the product end-of-life. This applies to your product and
any peripherals marked with this symbol. Do not dispose of these products as unsorted
municipal waste. Contact your local dealer for procedures for recycling this equipment.
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device mat not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Trademark Acknowledgements
iPad® & iPhone® are the registered trademarks of Apple Inc.
Android™ is a trademark of Google Inc. Use of this trademark is subject to Google Permissions.
Microsoft®, Windows® & Internet Explorer® are registered trademarks of Microsoft Corporation in the United
States and/or other countries.
Disclaimer
We reserve the right to revise or remove any content in this manual at any time. We do not warrant or assume
any legal liability or responsibility for the accuracy, completeness, or usefulness of this manual. The content of
this manual is subject to change without notice.
This product doesn’t have a standby / off mode.

MPEG4 Licensing
THIS PRODUCT IS LICENSED UNDER THE MPEG4 VISUAL PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN
COMPLIANCE WITH THE MPEG4 VISUAL STANDARD (“MPEG-4 VIDEO”) AND/OR (ii) DECODING
MPEG4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND
NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY
MPEG LA TO PROVIDE MPEG4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY
OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL INTERNAL
AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE
HTTP://WWW.MPEGLA.COM.
GPL Licensing
This product contains codes which are developed by Third-Party-Companies and which
are subject to the GNU General Public License (“GPL”) or the GNU Lesser Public
License (“LGPL”).
The GPL Code used in this product is released without warranty and is subject to the
copyright of the corresponding author.
Further source codes which are subject to the GPL-licenses are available upon request.
We are pleased to provide our modifications to the Linux Kernel, as well as a few new
commands, and some tools to get you into the code. To get the codes, please write to
[email protected].

TABLE OF CONTENTS
1. OVERVIEW......................................................................................................................................... 1
1.1 Product Features....................................................................................................................................... 1
1.2 Package Content....................................................................................................................................... 1
1.3 Cable Overview......................................................................................................................................... 1
1.4 External Alarm Connection (For selected models only) ............................................................................ 2
1.5 Insert a Micro SD card (For selected models only) ................................................................................... 2
2. CAMERA ACCESS WITH INTERNET EXPLORER............................................................................ 3
2.1 Camera Login............................................................................................................................................ 3
2.2 Control Panel Overview ............................................................................................................................ 3
2.3 Digital PTZ (DPTZ) Operations (For selected models only)...................................................................... 5
2.4 Event Record Search & Playback ............................................................................................................. 6
2.4.1 Event Icons.......................................................................................................................................................6
2.4.2 Playback Control Panel....................................................................................................................................6
3. CAMERA CONFIGURATIONS............................................................................................................ 7
3.1 System configuration menu....................................................................................................................... 7
3.2 Network ..................................................................................................................................................... 9
3.2.1 Network ............................................................................................................................................................9
3.2.2 QoS ..................................................................................................................................................................9
3.2.3 DDNS ...............................................................................................................................................................9
3.2.4 SNTP..............................................................................................................................................................10
3.2.5 FTP.................................................................................................................................................................10
3.2.6 MAIL ...............................................................................................................................................................10
3.2.7 SMS................................................................................................................................................................ 11
3.2.8 Filter ...............................................................................................................................................................12
3.2.9 UPnP / Bonjour...............................................................................................................................................12
3.2.10 RTP ..............................................................................................................................................................13
3.2.11 SNMP ...........................................................................................................................................................14
3.2.12 IEEE 802.1X (For selected models only) .....................................................................................................15
3.2.13 Network Share .............................................................................................................................................16
3.2.14 Network Failure Detection............................................................................................................................16
3.3 Camera ................................................................................................................................................... 16
3.3.1 Camera...........................................................................................................................................................16
3.3.2 Video ..............................................................................................................................................................17
3.3.3 ROI .................................................................................................................................................................17
3.3.4 Color...............................................................................................................................................................17
3.3.5 Audio (For selected models only)...................................................................................................................18
3.3.6 Advanced........................................................................................................................................................19
3.3.7 Privacy Mask (For selected models only) ......................................................................................................20
3.4 EVENT .................................................................................................................................................... 21
3.4.1 Event ..............................................................................................................................................................21
3.5 Record..................................................................................................................................................... 21
3.5.1 Record............................................................................................................................................................21
3.5.2 Record Timer..................................................................................................................................................21
3.6 Storage.................................................................................................................................................... 22
3.6.1 Memory ..........................................................................................................................................................22
3.7 Trigger ..................................................................................................................................................... 23
3.7.1 Trigger ............................................................................................................................................................23
3.7.2 Push Video (For selected models only) .........................................................................................................25
3.7.3 Snapshot ........................................................................................................................................................25
3.8 General ................................................................................................................................................... 26
3.8.1 General...........................................................................................................................................................26
3.8.2 Time................................................................................................................................................................27
3.8.3 Server Log......................................................................................................................................................27
3.8.4 Online .............................................................................................................................................................28
3.8.5 Account...........................................................................................................................................................28

3.8.6 Google Maps ..................................................................................................................................................29
3.8.7 Maintenance...................................................................................................................................................29
APPENDIX 1 PRODUCT SPECIFICATIONS........................................................................................ 31
APPENDIX 2 BIT RATE TABLE FOR REFERENCE ............................................................................ 34
APPENDIX 3 POE CONNECTION ....................................................................................................... 36
APPENDIX 4 API ID APPLICATION FOR SMS MESSAGING.............................................................. 37
APPENDIX 5 Q&A ................................................................................................................................ 39
APPENDIX 6 RECORDING TIME TABLE ............................................................................................ 41
APPENDIX 7 PREREQUISITES FOR NETWORK SHARE.................................................................. 42
A7.1 Check PC IP Address ........................................................................................................................... 42
A7.2 Create "Administrator" Account............................................................................................................. 43
A7.3 Share Folder ......................................................................................................................................... 44
APPENDIX 8 ENABLE PUSH VIDEO................................................................................................... 45
A8.1 What’s Push Video................................................................................................................................ 45
A8.2 Prerequisites......................................................................................................................................... 45
A8.3 Enable Push Video ............................................................................................................................... 45
A8.3.1 From iOS devices (iPhone / iPad) ...............................................................................................................45
A8.3.2 From Android Mobile Device........................................................................................................................46
APPENDIX 9 EAZY NETWORKING..................................................................................................... 47
A9.1 Via EagleEyes on iOS / Android Device ............................................................................................... 47
A9.1.1 Setup............................................................................................................................................................47
A9.1.2 Checking Remaining Data Allowance..........................................................................................................50
A9.1.3 Sharing Cloud Device Access with Other Account(s)..................................................................................50
A9.2 Via Internet Explorer on PC / Laptop .................................................................................................... 52
A9.2.1 Setup............................................................................................................................................................52
A9.2.2 Checking Remaining Data Allowance..........................................................................................................55
A9.2.3 Sharing Cloud Device Access to Other Account(s) .....................................................................................55
A9.3 Icons ..................................................................................................................................................... 57
APPENDIX 10 MICRO SD CARD COMPATIBLE LIST......................................................................... 58

1
1. OVERVIEW
1.1 Product Features
Free P2P Cloud EaZy Networking to connect your camera to the internet.
ONVIF standard supported to simplify system integration
POE (Power-over-Ethernet) support to eliminate the use of power cables and reduce installation costs
IR LEDs built-in for night surveillance
Remote Surveillance
-- Full compatibility with iOS & Android OS, and Internet Explorer on Windows operating system
(Optional) WDR / DWDR to increase image recognizability in overexposure and dark areas.
(Optional) Line in / out jacks available for audio transmission
(Optional) External alarm I/O device connection
1.2 Package Content
Standard Package
IR Camera Quick Guide
Optional Accessories
Screws & wall plugs Wrench
Sun shield screw for sun shield
Installation sticker Waterproof kit
1.3 Cable Overview
Cable Description
Power cable Connect to DC12V power supply.
Note: The power adapter is optional.
RJ45 network cable Connect it to the supplied RJ45 cable extender adapter for cable extension, and prepare another RJ45
network cable with suitable length for your connection.
GND Ground wire, used for reset default or external device connection.
Alarm-in* Reserved for connecting to an external alarm device. For details, please refer the user manual of your alarm
device.
Alarm-out* Reserved for connecting to an external alarm device. For details, please refer the user manual of your alarm
device.
RESET Remove the insulating coating of this wire, and twist it with a ground wire together to reset default. This will
reset all parameters, including the IP address to factory default settings.
Note: Disconnect power before twisting these two wires together, and connect to power again for
reset default.
Line in (Blue) * Support microphone connection.
Line out (Green) * Support speaker connection.
Selected models only

2
1.4 External Alarm Connection (For selected models only)
This camera supports external I/O device connection for easy connection.
Below shows you how to connect an external device to this camera.
1.5 Insert a Micro SD card (For selected models only)
For local video recording, a micro SD card slot can be found on the camera. The camera doesn’t support
hot-swapping. Please insert or remove the micro SD card with power disconnected.
Note: Only selected models are equipped with a micro SD card slot for local video recording. To know
how to directly access video footage saved in the microSD card on your PC / laptop, please refer
to “How to directly play video footage saved in the microSD card on PC” at page 22.
Note: Before inserting a micro SD card, make sure you’ve copied all important data saved in the card (if
any) to other storage media, or all data will be removed after inserting it to the camera.
Please follow the directions in the below graphic to insert Micro SD card properly:
Note: It’s recommended to use tweezers for inserting / removing Micro SD card.
Note: For the compatible list of the micro SD card, please refer to “APPENDIX 10 MICRO SD CARD
COMPATIBLE LIST” at page 58.

3
2. CAMERA ACCESS WITH INTERNET EXPLORER
This network camera can be accessed via Microsoft Internet Explorer and iOS / Android mobile devices with our
self-developed program EagleEyes installed depending on different using situations.
Before using the camera, make sure you have configured the network settings, and the network connection is fine.
For network configurations, please download “Advanced Network Setup”.
2.1 Camera Login
Step1: Open your web browser, and key in http://ipaddress:portnum in the URL address box.
For example, for the IP address 60.121.46.236 and port No. 888, please key in ”http://60.121.46.236:888” into
the URL address box, and press Enter.
Step2: In the login page, key in the user name and password, and enter the security code from the image below if any.
Then, click LOGIN.
Step3: The wizard is then started.
‧ To skip the wizard and directly access the camera live view, click Close.
‧ To directly access the camera live view without starting the wizard for the login next time, check Do not start wizard at
login.
Note: If you’re prompted to install VLC player, Software and Streaming Viewer, please agree to
proceed the installation.
Step5: When the login is successful, the live view is shown.
2.2 Control Panel Overview
Note: The buttons available depend on the device you have and the user level used to log in.

4
Function Icon User Level Description
Live
Supervisor / Power User
/ Normal User / Guest Switch to the live view page.
Backup Supervisor / Power User Enter the event record list for video playback.
For details, please refer to “2.4 Event Record Search & Playback’ at page 5.
DPTZ
Supervisor / Power User
/ Normal User
Switch to the DPTZ configuration page.
For details, please refer to “2.3 Digital PTZ (DPTZ) Operations (For selected
models only)” at page 4.
Config. Supervisor / Power User
Switch to the system configuration page. The functions available for
“Supervisor” and “Power User” are different.
For more details, please refer to “3.1 System configuration menu” at page 7.
Live player -- Supervisor / Power User
/ Normal User / Guest
Select the image player from the drop-down list:
ActiveX
QuickTime
QuickTime is Apple Inc.’s multimedia software. You need to have QuickTime
installed in your operating system before selecting “QuickTime”. When it is
selected, you will be promoted to enter the user name and password to access
the camera.
VLC
Quality -- Supervisor / Power User
/ Normal User
Click & drag the slider to select the video quality:
BASIC / NORMAL / HIGH / BEST.
Video Profile -- Supervisor / Power User
/ Normal User
Select the pre-defined video set from the drop list. The video set could be
configured in “Config” -> “Camera” -> “Video”.
Snapshot
Supervisor / Power User
/ Normal User
Click to take a snapshot of the current view on a new window. Right click
on the picture and re-save it to the location you want.
Manual Recording* /
Supervisor / Power User
/ Normal User
Click to start video recording manually.
This function is available only when the camera has a microSD card slot
and a microSD card is inserted to the camera.
Live View Size: Supervisor / Power User
/ Normal User
Full Screen
Click to display the image in full screen.
To exit the full screen mode, press “Esc” on your keyboard.
This icon appears only when the selected resolution is 640 x 480 or above.
Double size The QVGA resolution is resized to fit into the current live view size.
This icon appears only when the selected resolution is 320 x 240.
Fit to screen The selected resolution is resized to fit into the current live view size.
This icon appears only when the selected resolution is 1280 x 720 or above.
Normal Size
The current live view size is the same as the selected resolution.
This icon appears only when the selected resolution is 1280 x 720 or above.
No Scale
Click and hold the movable square on the left bottom corner of the live view
to move
This icon appears only when the selected resolution is 1280 x 720 or above.
Audio Switch* /
Supervisor / Power User
/ Normal User Click to switch the audio-in on / off.
Alarm Out*
Supervisor / Power User
/ Normal User
Click to force your alarm-out device to work. For example, when your
alarm device is a buzzer, click this button and your buzzer will start to
sound even if there’s no alarm event.
Microphone* / Supervisor Click to switch the audio-out on / off.
Zoom-in / out* /
Supervisor / Power User
/ Normal User
Click to zoom in / out the current image.
This function is available only when DPTZ is enabled.
Max. Zoom-in / out* /
Supervisor / Power User
/ Normal User
Click to zoom in the image to the largest / zoom out the image to its
original size.
This function is available only when DPTZ is enabled.
DPTZ*
Supervisor / Power User
/ Normal User
Click to enable the zoom-in / out function. To move the image in the
zoom-in mode, simply click on where you want to see in the live view.
For vari-focal models only.
Focus Zone*
Supervisor / Power User
/ Normal User
Click to change the focus zone if the current focus area is not what you
need. If you feel like the focus is not clear after the focus zone is changed,
click (Focus Near) / (Focus Far) to adjust the focus.
Focus Near / Far* /
Supervisor / Power User
/ Normal User Click to manually adjust the focus if needed.
* For selected models only

5
2.3 Digital PTZ (DPTZ) Operations (For selected models only)
This camera has PTZ capability, i.e. digital PTZ (hereafter called “DPTZ”), for wide area monitoring.
Click “DPTZ” to show the DPTZ control panel.
FUNCTION ICON DESCRIPTION
Moving panel -- When is selected, the moving control panel will be shown to move the picture after zoom-in is
performed.
Take snapshots Click to take a snapshot of the current view on a new window. Right click on the picture and re-save it
to the location you want.
Normal Size The current live view size is the same as the selected resolution.
This icon appears only when the selected resolution is 1280 x 720 or above.
Scale
Click and hold the movable square on the left bottom corner of the live view to move
This icon appears only when the selected resolution is larger than the current live view size.
Zoom in / out* / Click once to enlarge the picture by 1X, and click once to restore the zoom ratio by 1X.
Max. zoom in / out* / Click once to enlarge the picture to the max zoom ratio by 16X, and click once to restore the
picture ratio to 1X.
Focus near / far / Click to adjust the focus of the image.
Focus Zone*
Click to change the focus zone if the current focus area is not what you need. If you feel like the focus
is not clear after the focus zone is changed, click (Focus Near) / (Focus Far) to adjust the
focus.
* For selected models only

6
2.4 Event Record Search & Playback
Note: To save more recorded data, it’s recommended to use this camera with a compatible NVR.
Note: (For selected models only) If a microSD card has inserted to your camera for video recording,
you can also remove and insert the card to your PC for event search and playback. For details,
please refer to “How to directly play video footage saved in the microSD card on PC” at page 22.
2.4.1 Event Icons
External alarm Internal alarm Audio detection Manual
Motion System Timer
2.4.2 Playback Control Panel
/ Previous / Next Hour Click to jump to the next / previous time interval in an hour, for example, 11:00 ~ 12:00 or 14:00
~ 15:00, and start playing the earliest event video clip recorded during this whole hour.
Fast Forward Increase the speed for fast forward. Click to get 2X, 4X, 8X & 16X speed forward eventually.
Fast Rewind Increase the speed for fast rewind. Click to get 2X, 4X, 8X & 16X speed rewind eventually.
Play Click to play the current video clip.
Pause Click to pause the video playback.
Stop Click to stop the video playback.
Step In the pause mode, click to get one frame forward.
Audio Click to mute the playback if necessary, and click again to restore.
Download
Click to download the current video clip to the specified path in your PC.
The downloaded video can only be opened by our own video player. Please go to General → Maintenance to
download the video player, or get the player from the CD supplied with the sales package.

7
3. CAMERA CONFIGURATIONS
Users can further configure this network camera by accessing via Internet Explorer.
3.1 System configuration menu
Click Config. to enter the configuration page.
The functions are categorized into seven menus: Network, Camera, ONVIF, Record, Storage, Trigger and
General.
For details about “Network”, please refer to “3.2 Network” at page 9.
For details about “Camera”, please refer to “3.3 Camera” at page 15.
For details about “ONVIF”, please refer to “3.4 EVENT” at page 21.
For details about “Record”, please refer to “3.5 Record” at page 21.
For details about “Storage”, please refer to “3.6 Storage” at page 22.
For details about “Trigger”, please refer to “3.7 Trigger” at page 23.
For details about “General”, please refer to “3.8 General” at page 26.
Main Menu Sub-Menu Reference
Network Network Configure network settings.
QoS Limit the data flow for live streaming.
DDNS Enter DDNS information when the network type is PPPOE or DHCP.
SNTP Synchronize your camera time with the networked computer systems.
FTP Enter the FTP information for event notifications when FTP is chosen in Trigger →
Trigger.
Mail Enter Email information for event notifications when “Email is chosen in Trigger →
Trigger.
SMS Enter text messaging information for SMS notifications when SMS is chosen in Trigger →
Trigger.
Filter Choose to permit or block the IP address(es) which can access this camera.
UPnP
*Suitable for Windows-based operating system.
Allow this camera to be detected among devices within the same network area for easy and
quick usage.
Bonjour
*Suitable for Apple Mac-based operating system.
Allow this camera to be detected among devices within the same network area for easy and
quick usage.
RTP Set the parameters for video data transmission when you’re using multimedia other than web
browsers and Video Viewer for remote access.
SNMP Configure SNMP to remotely manage network devices.
IEEE 802.1X* The settings here enable the camera to access a network protected by 802.1X/EAPOL
(Extensible Authentication Protocol Over LAN).
Network Share Assign a location in the LAN environment to save the snapshot of events when Network
Share is chosen in Trigger →Snapshot.
Network Failure Detection Configure this camera to check the network connection of other device periodically, and send
notifications via Email or FTP for disconnection events.
Camera Camera 1. Rename the camera.
2. Change the place where the camera name is shown on the screen.
Video Adjust video-related settings in different video format.
ROI Select a specific area to reinforce the image quality of that area.
Color Adjust the color performance.
Audio* Adjust the audio volume of the microphone and speaker, and configure audio detection.
Advanced Adjust the camera parameters if necessary.
Privacy Mask* Cover certain areas on the camera image.
ONVIF Event This function is used to integrate the functions of event and alarm detection when this camera
has to work with other ONVIF-compliant device.
Record* Record Configure the record function.
Record Timer Schedule external alarm recording.
Storage* Memory Check the current storage capacity and clear all recorded data when needed.
*Selected models only

8
Main Menu Sub-Menu Reference
Trigger Trigger
1. Enable / disable the motion detection.
2. Set the motion detection area.
3. Configure how the camera reacts for any event.
Push Video* Configure to receive active alarm notifications within 5 seconds after event occurrence on
mobile devices.
Snapshot Schedule the camera to take snapshots periodically or at a specific time, and send to E-Mail,
FTP and / or Network Share for backup. Time-lapse recording could also be configured here.
General General
1. Select the language of the web browser.
2. Check the MAC address of the camera.
3. Lock camera access after the specified time.
Time Set daylight saving time and the current time.
Server Log Check the system event logs.
Online Check the current online user(s).
Account 1. Create a new user account with different access privilege.
2. Modify or delete an existing user account.
Google Maps Allow you to know where the network camera is.
Maintenance
1. Check the current firmware version and upgrade your camera.
2. Copy system configurations.
3. Reboot the camera.
4. Download the video player to play the recorded data.
*Selected models only

9
3.2 Network
3.2.1 Network
You can set the network configuration of the network camera depending on your network type.
For details, please see “Advanced Network Setup”.
Note: To know how to use EaZy Networking, please refer to “APPENDIX 9 EAZY NETWORKING” at page
47.
3.2.2 QoS
QoS, Quality of Service, is the ability to control the data flow for real-time streaming. This function is important if
your network bandwidth is insufficient and you have other devices to share the network bandwidth.
Check QoS Enable, and set the max. upload rate from 256 to 10240 kbps.
3.2.3 DDNS
Choose Enable when the selected network type in Network is PPPOE or DHCP.
For details, please see “Advanced Network Setup”.

10
3.2.4 SNTP
SNTP (Simple Network Time Protocol) is used to synchronize your camera time with the networked computer.
Function Description
GMT Once users choose the time zone, the network camera will adjust the local area time of the system
automatically.
NTP Server Simply use the default SNTP server (For example, tock.stdtime.gov.tw) or change to another server with
which users are familiar.
Sync. Period Select Daily to synchronize the camera time with the network time every day or “None” to turn off this
function.
Sync Click and the network camera will synchronize the time with the network time.
3.2.5 FTP
Enter the detailed FTP information and click Save to confirm. The information you set here will be applied when
FTP is selected in Trigger →Trigger.
3.2.6 MAIL
Enter the detailed e-mail information and click Save to confirm. The information you set here will be applied
when Email is selected in Trigger →Trigger.
Function Description
SMTP Server Enter the SMTP server address provided from your e-mail system supplier.
Port Enter the port number provided from your e-mail system supplier. If this column is left blank, the e-mail server will use
port 25 to send e-mails.
Mail From Enter the name of the sender.
SSL Encryption Select Yes if your e-mail server is using SSL encryption to protect your e-mail content from unauthorized access.

11
Function Description
Verify Password Some mail servers are required to verify the password. Please enter the “user name” and “password”.
Subject Enter the subject for the E-Mail.
E-Mail Address List Add the e-mail address(s) of the assigned recipient(s).
Test When all information is entered, click Test Mail to try if the receipt.
3.2.7 SMS
Note: Before using this function, you need to apply an account and get an API ID from the mobile
messaging company, such as Clickatell and EVERY8D. For details, please refer to “APPENDIX 4
API ID APPLICATION FOR SMS MESSAGING” at page 37.
Enter the detailed information needed for text messaging, and click Save to confirm. The information you set
here will be applied when SMS is selected in General →Trigger.
Function Description
System The text messaging service provider is Clickatell.
User name / Password Enter the account user name and password you created in Clickatell.
API ID Enter the API ID you applied from Clickatell.
Recipient Click Add to enter the phone number, including the country code, to receive the text
message. Five sets of phone numbers are allowed.
Transfer Interval Set the interval time in minutes between two-message sending.
The options are 0, 15, 30 & 60.
Reset Counter Click to restart the text messaging, and the SMS will be sent after the specified time interval
since you click this button.
Message Enter the text content (up to 70 characters) you want to send with the text message.
Test To know whether your SMS setting is correct, click this button to immediately send a SMS to
your phone.
Note: This testing is not free and you will be charged for SMS sending base on your
local rate.

12
3.2.8 Filter
Choose to permit or block the IP address(es) which can access this camera, and click Save to confirm.
Function Description
Filter Configuration
Error Count Set the maximum count for login failure. When the maximum count is reached, the IP address trying to access the
network camera will be locked.
Error Lock Time Set the lock time in minutes when the maximum count of error login for an IP address is reached.
Echo Request Select Non-Block to allow other users to use the ping command to detect the IP address of your network camera, or
Block to deny the ping command request.
IP/MAC Filter Configuration
IP/MAC Filter Choose to enable or disable the filter function.
IP/MAC Filter Policy If Enable is selected, choose whether you want to permit (Allow) or block (Deny) the IP address list below.
IP/MAC Filter Rules
Rule ‧ To add an item to the IP address list, key in the IP address in Rule, and click Add.
‧ To remove an existing item in the IP address list, click the item you want to remove, and click Delete.
3.2.9 UPnP / Bonjour
“UPnP” stands for “Universal Plug and Play”, which allows devices to connect seamlessly in the home and
corporate environments and simplify installation of computer components, and is only suitable for Microsoft
Windows-based operating system.
“Bonjour” functions the same as “UPnP”, but it’s only suitable for Apple Mac-based operating system.
UPnP
Bonjour
Check Enable to allow the network camera to be detected among devices within the same network area, and
set the identification name of the camera in Friendly name.
When this function is activated, the other PC within the same domain as this camera will be able to search this
camera in:
Network Neighbor with the identification name set in Friendly name for Windows-based PC, or
“ ” (finder) or Bookmark with the identification name set in Device Name for Mac-based PC.

13
Double-click it to quickly open the web browser for camera access.
Port Mapping (Available only in UPnP)
This function can eliminate the need to additionally access the router for port forwarding.
For details, please download “Advanced Network Setup”.
Note: Before using this function, make sure your router supports UPnP, and this function is enabled. If
not, please access your router additionally for port forwarding.
When Port Mapping is set to Enable, the system will automatically assign an IP address or port number for
you if no IP address or port number is entered.
Note: When the configurations are saved successfully, you’ll see a message indicating the IP address
and port number assigned to this network camera.
3.2.10 RTP
The Real-time Transport Protocol (RTP) is an Internet protocol standard to manage the real-time transmission of
multimedia, such as VLC player.
The media player you want to use for remote access must support RTP transmission for this function to work
normally.
Note: When you’re about to end the remote access, please press the stop button on your media player
first, and then close the program. This is to ensure the server receives the stop command, and
also help to protect the server from redundant data transmission.

14
Function Description
Port Range
The port range used by RTP is limited, and preserving 100 ports between the start port and end port is necessary.
Start Port The range of the start port is 1024 ~ 65434.
End Port The range of the end port is 1124 ~ 65534.
Video
Address and port for
video transmission
Set a specific address and port for multicast of profile 1 ~ 4.
The range of the address is limited between 224.0.0.1 ~ 239.255.255.255.
The port for multicast must be an even number.
Audio (For selected models only)
Address and port for
audio transmission
Set a specific address and port for multicast of audio.
The range of the address is limited between 224.0.0.1 ~ 239.255.255.255.
The port for multicast must be an even number.
3.2.11 SNMP
SNMP, Simple Network Management Protocol, is used to facilitate the exchange of management information
between network-attached devices, and network administrators could use it to monitor those devices.
The SNMP consists of three basic components:
Network-management systems (NMSs) to monitor and control the managed devices.
Managed devices as network nodes to save all network and management information, such as routers, access
servers, switches, bridges, hubs, etc.
Agents as network management software modules on managed devices to provide the status of managed devices
to NMSs.
Note: Before configuring SNMP settings, make sure your NMS is enabled first.
Enable SNMP V1 / V2C
Select Yes to enable this function, and enter the names of Read community and Write community based
on your NMS configurations.
To enable Traps to notify the management station of important events, choose V1 or V2C in Enable, enter
the address and community name, and select the event type(s) needed.

15
Enable SNMP V3
SNMP V3 has a higher security level than SNMP V1 / V2C to allow configuring the authentication password and
encryption password.
Choose Read/Write Security name or Read only Security name based on your NMS settings, and
enter the community name. Then, select the authentication type from MD5 or SHA, and enter the password for
authentication and encryption. The password length is from 8 to 31 characters.
3.2.12 IEEE 802.1X (For selected models only)
The settings here enable the camera to access a network protected by 802.1X/EAPOL (Extensible
Authentication Protocol Over LAN).
Note: For authentication to work properly, it's important to synchronize the time in the camera with an
NTP server.
Before using this function, make sure:
The switch and RADIUS server you have in the LAN environment supports IEEE 802.1X, and IEEE 802.1X
settings are enabled.
You’ve applied a digital certificate from a Certificate Authority which can be validated by a RADIUS server,
and the identity and password used.
Then, follow the steps below:
Step1: Connect this camera to a PC or laptop directly, and go to its login page to log in.
Note: To know how to connect the camera to a PC or laptop directly, please check “4 Modem / Hub +
Modem” in “ADVANCED NETWORK SETUP”.
Step2: Log into the camera, and go to Config Network IEEE 802.1X. Enable this function, and select
the EAP method you want to use.
Note: This camera supports EAP-PEAP, EAP-TLS and EAP-TTLS.
Step3: Enter the identity and password you get from the Certificate Authority, and select the EAPOL version
used in your switch.
Step4: Upload the certificate(s) issued by the Certificate Authority, and save.
Step5: Disconnect the camera from your PC or laptop, and connect it to the switch in the LAN environment you
want to use IEEE 802.1x, and the camera will start the authentication later.