Avtech DG104A User manual

680Z
d104a_V0.9
IR Dome Camera User Manual
The product image may differ from the actual product.
Please use this camera with a DVR which supports HD video recording.
Please read the instructions thoroughly before using the product.
C
CA AU UT TI IO ON N
R
RI IS SK K O OF F E EL LE EC CT TR RI IC C S SH HO OC CK K
C
CA AU UT TI IO ON N: :
To reduce the risk of electric shock, do not expose this apparatus to rain or moisture.
Only operate this apparatus from the type of power source indicated on the label.
The company shall not be liable for any damages arising out of any improper use, even if we have been advised of the possibility of
such damages.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
This exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
ROHS Announcement
All lead-free products offered by the company comply with the requirements of the European law on the Restriction
of Hazardous Substances (RoHS) directive, which means our manufacture processes and products are strictly
“lead-free” and without the hazardous substances cited in the directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product must be collected
separately at the product end-of-life. This applies to your product and any peripherals marked with this symbol. Do
not dispose of these products as unsorted municipal waste.
CE Mark
This apparatus is manufactured to comply with the radio interference.
The company does not warrant that this manual will be uninterrupted or error-free. We reserve the right to revise or
remove any content in this manual at any time.

FEATURES
1. 1/2.7” CMOS Sensor
2. 1080P video output
3. Low light sensitivity of 0.1 Lux / F1.8, 0Lux (IR LED ON)
4. Day and night 24-hour surveillance with IR effective distance up to 15 meters
PACKAGE CONTENT
IR camera * 1 User manual * 1
DIMENSIONS*
*Dimensional Tolerance: ± 5mm
SPECIFICATIONS*
Pick-up Element 1/ 2.7” CMOS image sensor
Number of Pixels 1930(H) x 1088(V)
Video Frame Rate 1080P@30fps / 1080P@25fps
Min. Illumination 0.1 Lux / F1.8, 0 Lux (IR LED ON)
S/N Ratio More than 48dB (AGC OFF)
Shutter Speed 1/30 (1/25) sec ~ 1/720000 (1/600000) sec
Lens f3.6mm / F1.8
Lens Angle 96° (Horizontal) / 50° (Vertical) / 116° (Diagonal)
IR LED 12 units
IR Effective Distance Up to 15 meters
IR Shift YES
Day & Night Mode YES
IRIS Mode AES
White Balance AUTO / USER / PUSH / 8000K / 6000K / 4200K / 3200K
AGC Adjustable
Sharpness Adjustable
Flickerless 50HZ / 60HZ / OFF
BLC Adjustable
IP Rating IP66
Operating Temperature -20℃~ 40℃
Video Output 1.0 Vp-p composite, 75Ω
Power Source (±10%) DC12V / 0.5A
Current Consumption (±10%) 200mA
* The specifications are subject to change without notice.

INSTALLATION
Step1: Remove the camera base as shown in Figure 1, and disassemble the camera to four parts as shown in Figure 2.
Rotate anti-clockwise Remove
Camera lens Part 1 Part 2Base
Figure 1 Figure 2
Step2: Locate where you want to install this camera (wall or ceiling), and drill holes on the wall or ceiling for securing the
bracket and routing the cables (if necessary).
Step3: Attach the bracket to the wall (or ceiling), and make sure the cables are routed and arranged properly in the bracket,
as shown in Figure 3.
Step4: Secure the bracket to the wall (or ceiling), as shown in Figure 4.
W
here to look
Cable routing
Attach to wall (or ceiling)
Figure 3 Figure 4
Step5: Slightly adjust the camera lens to where it’s supposed to face, and replace Part 1 and Part 2 back, as shown in
Figure 5 and Figure 6.
Step6: Hold the camera lens and Part 1, and rotate only Part 2 clockwise, as shown in Figure 6.
Part 1
Hold camera & Part 1, and
rotate only Part 2 clockwise
Part 2
Figure 5 Figure 6
Step7: Power on your camera, and check the viewing angle on the PC.
Step8: Adjust the position and the viewing angle of the camera, if necessary.

CONNECTION
1. DC12V Input Terminal
Connect the power terminal of the camera to a DC 12V regulated power supply.
NOTE: Please use the correct power adaptor, DC12V (regulated), to operate this unit. The power
tolerance of this unit is DC12V ± 10%. Over maximum DC 12V power input will damage this
unit.
2. Video Output Connector (VIDEO OUT)
Connect the camera video output to the video input of a DVR with 75Ωcoaxial cable.
NOTE: To ensure the camera has sufficient protection against moisture, an extra waterproof
measure, such as by using an insulating tape, must be used to cover the power and video
connectors after connection.
CAMERA PARAMETERS
This camera series has its own configuration menu, and either of the two methods below is available to
access the menu based on the camera model you have.
NOTE: The methods below are available only when the camera is used with our brand’s HD CCTV
DVR.
Method 1
On the DVR live view, click the channel which connects this camera to display in the full screen mode,
and select to show the control panel, and select to enter the camera menu.
Method 2
On the DVR live view, right click to show the DVR main menu, and select “ADVANCED CONFIG” 
“DCCS”. Then, select the channel which connects this camera, and click “SETUP” to enter the menu of
camera parameters.
ADVANCED CONFIG
C A M E R A CH1 CH2 CH3 CH4
DETECTION MENU SETUP
ALERT
NETWORK
DISPLAY
RECORD
DEVICES
DCCS DEVICE XXXXX
NOTIFY CONNECTION OK
EXIT
NOTE: The parameters available depend on the model you have.