Avtech DG206 User manual

696Z
d206x_V1.0
IR Dome Camera User Manual
The product image may differ from the actual product.
Please use this camera with a DVR which supports HD video recording.
Please read the instructions thoroughly before using the product.
C
CA AU UT TI IO ON N
R
RI IS SK K O OF F E EL LE EC CT TR RI IC C S SH HO OC CK K
C
CA AU UT TI IO ON N: :
To reduce the risk of electric shock, do not expose this apparatus to rain or moisture.
Only operate this apparatus from the type of power source indicated on the label.
The company shall not be liable for any damages arising out of any improper use, even if we have been advised of the possibility of
such damages.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
This exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
ROHS Announcement
All lead-free products offered by the company comply with the requirements of the European law on the Restriction
of Hazardous Substances (RoHS) directive, which means our manufacture processes and products are strictly
“lead-free” and without the hazardous substances cited in the directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product must be collected
separately at the product end-of-life. This applies to your product and any peripherals marked with this symbol. Do
not dispose of these products as unsorted municipal waste.
CE Mark
This apparatus is manufactured to comply with the radio interference.
The company does not warrant that this manual will be uninterrupted or error-free. We reserve the right to revise or
remove any content in this manual at any time.

FEATURES
1. 1/2.9” CMOS Sensor
2. 1080P video output
3. f2.8 ~ 12mm vari-focal lens
4. Low light sensitivity of 0.1 Lux / F1.4(Wide)~F2.8(Tele), 0Lux (IR LED ON)
5. IP66 for weather-proof application
PACKAGE CONTENT
IR camera User manual Wrench
Tool for focal length & focus adjustment Screws & wall plugs
DIMENSIONS
*Dimensional Tolerance: ± 5mm
SPECIFICATIONS*
Pick-up Element 1/ 2.9” CMOS image sensor
Number of Pixels 1936(H) x 1096(V)
Video Frame Rate 1080P@30fps / 1080P@25fps
Min. Illumination 0.1 Lux / F1.4(Wide)~F2.8(Tele), 0 Lux (IR LED ON)
S/N Ratio More than 48dB (AGC OFF)
Shutter Speed 1/30 (1/25) sec ~ 1/33750 (1/28125) sec
Lens f2.8 ~ 12mm / F1.4 ~ F2.8
Lens Angle Wide: 103° (Horizontal) / 54° (Vertical) / 122° (Diagonal)
Tele: 31° (Horizontal) / 17° (Vertical) / 36° (Diagonal)
IR LED 24 units
IR Effective Distance Up to 20 meters
IR Shift YES
Day & Night Mode YES
IRIS Mode AES
White Balance AUTO / INDOOR / OUTDOOR / USER
AGC High / Middle / Low / Off
Sharpness Adjustable
IP Rating IP66
Operating Temperature -20℃~ 40℃
Power Source (±10%) DC12V / 1A
Current consumption (±10%) 210mA (IR OFF); 430mA (IR ON)
* The specifications are subject to change without notice.

INSTALLATION
Step1: Find the screw on the camera, and remove it with the supplied wrench.
Then, remove the camera base as shown in Figure 1, and disassemble the camera to four parts as shown in
Figure 2.
Figure 1
Figure 2
Step2: Locate where you want to install this camera (wall or ceiling), and drill holes on the wall or ceiling for securing the
bracket and routing the cables (if necessary).
Step3: Attach the bracket to the wall (or ceiling), and make sure the cables are routed and arranged properly in the bracket,
as shown in Figure 3.
Figure 3
Step4: Secure the bracket to the wall (or ceiling), as shown in Figure 4.
Figure 4

Step5: Slightly adjust the camera lens to where it’s supposed to face, and replace Part 1 and Part 2 back, as shown in
Figure 5 and Figure 6.
Step6: Hold the camera lens and Part 1, rotate only Part 2 clockwise to the end, and replace the screw removed in Step1
back, as shown in Figure 6.
Figure 5
Figure 6
Step7: Power on your camera, and check the viewing angle on the PC.
Step8: Adjust the position, viewing angle, focal length and focus of the camera, if necessary.
For focal length and focus adjustment, please check Figure 7 to know where to do.
Figure 7

CONNECTION
1. DC12V Input Terminal
Connect the power terminal of the camera to a DC 12V regulated power supply.
NOTE: Please use the correct power adaptor, DC12V (regulated), to operate this unit. The power
tolerance of this unit is DC12V ± 10%. Over maximum DC 12V power input will damage this
unit.
2. Video Output Connector (VIDEO OUT)
Connect the camera video output to the video input of a DVR with 75Ωcoaxial cable.
NOTE: To ensure the camera has sufficient protection against moisture, an extra waterproof
measure, such as by using an insulating tape, must be used to cover the power and video
connectors after connection.
CAMERA PARAMETERS
This camera series has its own configuration menu, and either of the two methods below is available to
access the menu based on the camera model you have.
NOTE: The methods below are available only when the camera is used with our brand’s HD CCTV
DVR.
Method 1
On the DVR live view, click the channel which connects this camera to display in the full screen mode,
and select .
Click “” to enter the menu of camera parameters.
Method 2
On the DVR live view, right click to show the DVR main menu, and select ADVANCED CONFIG 
DCCS. Then, select the channel which connects this camera, and click SETUP.
Click “” to enter the menu of camera parameters.
ADVANCED CONFIG
C A M E R A CH1 CH2 CH3 CH4
DETECTION MENU SETUP
ALERT
NETWORK
DISPLAY
RECORD
DEVICES F.W. 1015
DCCS DEVICE XXXXX
NOTIFY CONNECTION OK
EXIT
When the camera menu is entered, you’ll see the keys on the bottom right corner to
move between and change those configurations.
 Move between selections or change settings.
Enter the currently-selected item.
X Quit the camera parameters mode.

MENU DESCRIPTION
EXPOSURE LENS TYPE FIX No function.
SHUTTER
AUTO / 1/25 / 1/30 / 1/50
/ 1/60 / 1/100 / 1/ 120 /
1/250 / 1/500 / 1/1000 /
1/3000 / 1/10000
Set the shutter speed for exposure.
AGC OFF / LOW / MIDDLE /
HIGH
Set the level of Auto Gain Control to automatically
adjust the image when the light level changes.
EXPOSURE VALUE 1 ~ 17 Set the value for exposure.
WHITE
BALANCE
MODE AUTO / INDOOR /
OUTDOOR / USER
Set the white balance mode among AUTO,
INDOOR, OUTDOOR and USER.
DAY & NIGHT MODE EXT / COLOR / B/W Set the day & night mode among EXT, COLOR
and B/W..
IMAGE BRIGHTNESS 1 ~ 256 Set the level of brightness to adjust the brightness
of the image.
CONTRAST 1 ~ 256 Set the level of contrast.
COLOR GAIN 1 ~ 256 Set the level of gain.
SHARPNESS 1 ~ 256 Set the level of sharpness to enhance the clarity of
image detail by adjusting the aperture and
sharpening the edges.
NR OFF / LOW / MIDDLE
HIGH
Set the noise reduction mode to LOW / MIDDLE /
HIGH to suppress the noise based on the current
environment, or select OFF to disable this function.
MIRROR NONE / H / V / HV Rotate the images horizontally (H) or vertically (V),
or horizontally & vertically (HV) simultaneously
based on your installation situation when
necessary.
LANGUAGE ENGLISH / 中文(簡) Select the language of the menu: English /
Simplified Chinese.
FUNC. SET MOTION DETECTON SCREEN ALARM Select ON to enable motion detection or OFF to
disable this function.
PAD OUTPUT No function.
SECTION Select the area for motion detection.
SENSITIVITY
Select the sensitivity for motion detection from
LOW, MIDDLE and HIGH.
PRIVACY MASKING Select ON / OFF to enable / disable this function.
COLOR Select a color to show area masking.
HEIGHT / WIDTH / LEFT
/ RIGHT / TOP / BOTTOM
Set the area to mask.
SYSTEM SETUP OSD COLOR Select the color for this OSD display.
OSD BG Select the background color for this OSD display.
RESET FACTORY MODE
Enable to restore the camera parameters to factory
default values.
SAVE & EXIT SAVE & EXIT Select YES to save and exit, or select NO to exit
without saving.