AXIOMTEK ICO300-83B User manual

ICO300-83B
Robust Din-rail Fanless Embedded
System
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate
information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of
patents or any third party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the
accuracy, completeness or usefulness of any information in this document. Axiomtek
does not make any commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any
time without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd.
Copyright 2017 Axiomtek Co., Ltd.
All Rights Reserved
November 2017, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, please read the following important safety precautions.
1. The ICO300 does not come equipped with an operating system. An operating
system must be loaded first before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in
any static-shielded devices. Most electronic components are sensitive to static
electrical charge.
3. Disconnect the power cord from the ICO300 before making any installation. Be
sure both the system and the external devices are turned OFF. Sudden surge of
power could ruin sensitive components. Make sure the ICO300 is properly
grounded.
4. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
5. Turn OFF the system power before cleaning. Clean the system using a cloth
only. Do not spray any liquid cleaner directly onto the screen.
6. Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -45℃or above 85℃. It may damage the equipment.
7. Do not open the system’s back cover. If opening the cover for maintenance is a
must, only a trained technician is allowed to do so. Integrated circuits on
computer boards are sensitive to static electricity. To avoid damaging chips
from electrostatic discharge, observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of
the system unit chassis for a few seconds. This will help to discharge any
static electricity on your body.
When handling boards and components, wear a wrist-grounding strap,
available from most electronic component stores.
8. Caution
Risk of explosion if battery is replaced by an incorrect type dispose of used
batteries according to the instructions.
9. Warning
Hot Surface Do NoT Touch.
Restricted access area: The equipment should only be installed in a Restricted
Access Area.
10. This product is intended to be supplied by a Listed Power Adapter or DC power
source, output meets SELV, rated 12-24Vdc, minimum 2.42-1.29A, Tma = 70
degree C, and the altitude of operation = 5000m.
If need further assistance with purchasing the power source, please contact to
manufacturer for further information.

iv
Classification
1. Degree of production against electric shock: not classified
2. Degree of protection against the ingress of water: IP40
3. Equipment not suitable for use in the presence of a flammable anesthetic
mixture with air or with oxygen or nitrous oxide.
4. Mode of operation: Continuous
5. Type of protection against electric shock: Class I equipment
General Cleaning Tips
You may need the following precautions before you begin to clean the computer.
When you clean any single part or component for the computer, please read and
understand the details below fully.
When you need to clean the device, please rub it with a piece of dry cloth.
1. Be cautious of the tiny removable components when you use a vacuum cleaner
to absorb the dirt on the floor.
2. Turn the system off before you start to clean up the component or computer.
3. Never drop the components inside the computer or get circuit board damp or
wet.
4. Be cautious of all kinds of cleaning solvents or chemicals when you use it for
the sake of cleaning. Some individuals may be allergic to the ingredients.
5. Try not to put any food, drink or cigarette around the computer.

v
Cleaning Tools
Although many companies have created products to help improve the process of
cleaning your computer and peripherals users can also use household items to clean
their computers and peripherals. Below is a listing of items you may need or want to
use while cleaning your computer or computer peripherals.
Keep in mind that some components in your computer may only be able to be
cleaned using a product designed for cleaning that component, if this is the case it
will be mentioned in the cleaning.
Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although
paper towels or tissues can be used on most hardware as well, we still recommend you
to rub it with a piece of cloth.
Water or rubbing alcohol: You may moisten a piece of cloth a bit with some
water or rubbing alcohol and rub it on the computer. Unknown solvents may be
harmful to the plastics parts.
Vacuum cleaner: Absorb the dust, dirt, hair, cigarette particles, and other
particles out of a computer can be one of the best methods of cleaning a
computer. Over time these items can restrict the airflow in a computer and
cause circuitry to corrode.
Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are
excellent tools for wiping hard to reach areas in your keyboard, mouse, and
other locations.
Foam swabs: Whenever possible it is better to use lint free swabs such as foam
swabs.
Note: We strongly recommended that you should shut down the system before you start
to clean any single components.
Please follow the steps below:
1. Close all application programs
2. Close operating software
3. Turn off power
4. Remove all device
5. Pull out power cable

vi
Scrap Computer Recycling
If the computer equipments need the maintenance or are beyond repair, we strongly
recommended that you should inform your Axiomtek distributor as soon as possible
for the suitable solution. For the computers that are no longer useful or no longer
working well, please contact your Axiomtek distributor for recycling and we will make
the proper arrangement.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd. IBM, PC/AT, PS/2, VGA are
trademarks of International Business Machines Corporation.
Intel®and Pentium®are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBASIC are trademarks of Microsoft Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.Other brand names and
trademarks are the properties and registered brands of their respective owners.

vii
Table of Contents
Safety Precautions................................................................................................ iii
Classification......................................................................................................... iv
General Cleaning Tips ..........................................................................................iv
Scrap Computer Recycling..................................................................................vi
CHAPTER 1 INTRODUCTION................................................................................1
1.1 General Description...........................................................................1
1.2 System Specifications.......................................................................3
1.2.1 CPU ...................................................................................................................3
1.2.2BIOS ..................................................................................................................3
1.2.3System Memory ...............................................................................................3
1.2.4Display ..............................................................................................................3
1.2.5Ethernet Ports ..................................................................................................3
1.2.6Storages............................................................................................................3
1.2.7 Wireless ............................................................................................................3
1.2.8USB ...................................................................................................................4
1.2.9COM...................................................................................................................4
1.2.10 Power................................................................................................................4
1.2.11 Power Button (ICO300-83B-PB) .....................................................................5
1.2.12 DIO (ICO300-83B-DIO).....................................................................................5
1.2.13WatchDog Timer (WDT) ..................................................................................5
1.2.14Restore BIOS Optimal Defaults (JP2)............................................................5
1.2.15System LED......................................................................................................6
1.2.16Operation Temperature...................................................................................6
1.2.17Storage Temperature ......................................................................................6
1.2.18 Humidity ...........................................................................................................6
1.2.19 Weight...............................................................................................................6
1.2.20 Dimensions ......................................................................................................6
1.2.21 System I/O Outlets...........................................................................................6
1.3 Dimensions ........................................................................................7
1.4 I/O Outlets ..........................................................................................9
CHAPTER 2 HARDWARE INSTALLATION.......................................................13
2.1 Installing the Memory Module......................................................... 13
2.2 Installing the mSATA/Wireless module.......................................... 15
2.3 Installing the Hard Disk Drive ......................................................... 17
2.4 Installing Din-rail Mounting............................................................. 19
2.5 Installing Wall Mounting (optional).................................................21
CHAPTER 3 AMI UEFI BIOS UTILITY................................................................23
3.1 Entering Setup ................................................................................. 23
3.2 The Main Menu.................................................................................24
3.3 Advanced Features..........................................................................25
3.4 Chipset Feature................................................................................ 41
3.5 Security............................................................................................. 43
3.6 Boot Type .........................................................................................45

viii
3.7 Save & Exit.......................................................................................49
APPENDIX A WATCHDOG TIMER......................................................................53
About Watchdog Timer ................................................................................... 53
How to Use Watchdog Timer..........................................................................53
APPENDIX B POWER BUTTON SETTING FOR WINDOW SOFTWARE ...55

ICO300-83B User’s Manual
Introduction
1
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications of the ICO300. The
Chapter 1 includes the following sections:
General Description
System Specification
Dimensions
I/O Outlets
1.1 General Description
ICO300 Din-rail fanless embedded system is suitable for communications control and for
protocol converter applications in critical environments. Built for rugged work environments,
ICO300 features an extra low power consumption Intel® ATOM™E3930 (1.3GHz) or E3940
(1.6GHz) or Intel® ATOM™N3350(1.1GHz) processors supporting industrial temperature
range of -20℃to +70℃. Its front accessible I/O cabling is very convenient for wiring and
maintenance. ICO300 offers a VGA output, making it particularly well-suited for
communication control, SCADA and industrial automation. Its compact size with Din-rail
mounting allows for easy installation into control cabinet. Pre-installed with Linux, Windows®
10 embedded, ICO300 provides programmers with a friendly environment for developing
application software at a lower cost.
ICO300 is robust industrial-grade hardware design and adopts the advanced cooling system,
besides, supporting the mSATA and SATA SSD (or HDD), which makes it especially suitable
for field control & monitoring system solution for following markets:
Utility Industries (Water; Energy; Chemical Plant; Mining…)
Public Transportation Industries (Traffic/ Highway Control; Train/Bus Control…)
Homeland Security (Weather Monitoring/Alarm System…)
Checklist
ICO300 System Unit x 1
Power terminal block x 1
Screws
CF Mylar x 1
Cable Tie x1
DVD x 1 (for Driver)
Din-rail Kit x1
SATA+Power HDD cable x1
Note:Please contact your local vendors if any damaged or missing items.

ICO300-83B User’s Manual
Introduction
2
Features
Fanless design
Wide temperature operation of -20℃- +70℃(-40℃- +70℃for optional)
2 10/100/1000 Base-T Ethernets with Magnetic Isolated Protection
4 COM Ports support RS-232/422/485
2 Wireless (USB and PCIe Interface)
Support one 2.5”SATA drive bay (or mSATA )
Wide range 12–24V DC-in with terminal block
1 DI/DO (8-bit programmable, DB9 female connector) (ICO300-83B-DIO)
Din-rail mounting
Wall mounting (optional)
Passed CE with FCC testing
Embedded O.S. Supported
ICO300 not only supports Windows®10, but also supports embedded OS, such as
Windows®10 embedded and Linux package support. For storage device, ICO300
supports one SATA SSD (or HDD) and one mSATA.

ICO300-83B User’s Manual
Introduction
3
1.2 System Specifications
1.2.1 CPU
Onboard Intel® ATOM™E3930 (1.3GHz) or E3940 (1.6GHz) or Intel® ATOM™N3350
(1.1GHz)
1.2.2 BIOS
AMI (American Megatrends Inc.) UEFI (Unified Extensible Firmware Interface)
BIOS.
1.2.3 System Memory
One DDR3L 204-pin SO-DIMM (1.35V) slot.
Supports 1333/1600 MHz up to 8GB.
1.2.4 Display
A slim type 15-pin D-Sub connector as VGA connector.
1.2.5 Ethernet Ports
LAN Chip: Intel Ethernet Controller I211-AT.
LAN Chip: Intel Ethernet Controller I210-IT.(ICO300-83B-WT)
LAN 1 and LAN 2
The board has dual RJ-45 connectors, support 10/100/1000 Base-T with 1.5KV
magnetic isolated protection.
1.2.6 Storages
1 x 2.5”SATA drive bay.
1 x mSATA.
1.2.7 Wireless
2 x Full size Mini Card slot supports module with USB and PCIe Interface.
1 x SIM Card Socket.
3 x Antenna holes.

ICO300-83B User’s Manual
Introduction
4
1.2.8 USB
4x USB3.0
USB Pin Define :
Pin
Signal
USB Port 0
Pin
Signal
USB Port 1
1 2 3 4
5 6 7 8
1
VCC
5
VCC
2
D-
6
D-
3
D+
7
D+
4
GND
8
GND
1.2.9 COM
4 ports DB9 support RS-232/422/485 which can be selected by BIOS.
Supports Auto Flow Control in RS485 mode.
Serial Port Pin Define: (DB9 Male) as below
COM1~4
Pin
RS-232
RS-422
RS-485
1
DCD
TX-
Data-
2
RXD
TX+
Data+
3
TXD
RX+
--
4
DTR
RX-
--
5
GND
GND
GND
6
DSR
--
--
7
RTS
--
--
8
CTS
--
--
9
RI
--
--
1.2.10 Power
Wide-range 12 - 24V DC power input with terminal block.
OVP and Reverse protection.
Pin
Signal
1
+
2
NC
3
-

ICO300-83B User’s Manual
Introduction
5
1.2.11 Power Button (ICO300-83B-PB)
AT auto power on
Power button setting for software must be setted up firstly.
Note: Power button setting for Window software is offered on APPENDIX B for
reference.
1.2.12 DIO (ICO300-83B-DIO)
One DB9 female connector supports 8 bits TTL level programmable digital
input/output
The voltage of TTL is 5V
The programming is as follow:
- I/O sink current is 8~10mA (Output drive current ± 50 mA)
- Input/Output can be programmed
Pin
Signal
1
DIO0
2
DIO1
3
DIO2
4
DIO3
5
DIO4
6
DIO5
7
DIO6
8
DIO7
9
GND
1.2.13 WatchDog Timer (WDT)
1~255 seconds or minutes; up to 255 levels.
1.2.14 Restore BIOS Optimal Defaults (JP2)
Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing
this procedure can restore BIOS optimal defaults.
Function
Setting
Normal (Default)
1-2
Restore BIOS optimal defaults
2-3

ICO300-83B User’s Manual
Introduction
6
1.2.15 System LED
There are showed the LED’s indicators and functional descriptions.
LED Name
Description
Color
ACT
Indicate the storge status and it’s flashing when storge
access.
Green
PWR
Indicate the Power status. When the DC input is acceptable,
the LED will ON.
Yellow
1.2.16 Operation Temperature
-20℃~ +70℃
-40℃~ +70℃(optional for ICO300-83B-WT)
1.2.17 Storage Temperature
-40℃~ +85℃
1.2.18 Humidity
10% ~ 95% (non-condensation)
1.2.19 Weight
1 kg
1.2.20 Dimensions
48mm(1.88”) (W) x110mm(4.33”) (D) x155mm(6.1”) (H)
1.2.21 System I/O Outlets
Four 9-pin D-Sub male connectors, COM1~COM4.
One 15-pin D-Sub female connector for VGA.
Two 10/100/1000 Base-T RJ-45 with 1.5KV magnetic isolated protection.
Four USB 3.0 connectors.
One DC Power Input with terminal block.
One 9-pin D-Sub Female connectors for DIO. (ICO300-83B-DIO)
Three Antenna holes.

ICO300-83B User’s Manual
Introduction
7
1.3 Dimensions
The following diagrams show you dimensions and outlines of the ICO300-
83B/ICO300-83B-DIO/ICO300-83B-PB/ICO300-83B-DIO-PB.

ICO300-83B User’s Manual
Introduction
8

ICO300-83B User’s Manual
Introduction
9
1.4 I/O Outlets
The following figures show you I/O outlets on front view and top view of the ICO300-
83B/ICO300-83B-DIO/ICO300-83B-PB/ICO300-83B-DIO-PB.

ICO300-83B User’s Manual
Introduction
10

ICO300-83B User’s Manual
Introduction
11

ICO300-83B User’s Manual
Introduction
12