AXIOMTEK NANO830 User manual

4 9418K830000E
©Copyright 2012 Axiomtek Co., Ltd.
Version A1 December 2012
Printed in Taiwan
Bottom View
Quick Start
The basic procedures required to power on NANO830/831:
(1). Require at least 60W DC adapter. Ensure that all necessary
peripheral devices are plugged properly.
(2). Check the jumper settings and make sure they are in the
default position; especially JP10 (close).
(3). Firmly install DDR3 memory modules into connector SDIMM1
until fully seated.
(4). Firmly insert the DC adapter into CN17.
(5). Install a momentary on/off button/switch onto CN6, pin 9 and
10. See image above.
(6). Press the power button to start NANO830/831.
NANO830/831 Series Quick Installation Guide
9418K830000E 1
©Copyright 2012 Axiomtek Co., Ltd.
Version A1 December 2012
Printed in Taiwan
Checklist
9CPU Board x1 9Product Information CD x1
9Quick Installation Guide x1 9COM Port Cable with Bracket,
P=2.0mm x1
Note: Please contact your local vendors if any damaged or missing items. DO
NOT apply power to the board if there is any damaged component.
Note: Please refer to the NANO830/831 series product information CD for the
complete user’s manual, drivers and utilities. User’s manual and related
documents are in Acrobat PDF format.
Note: After installing graphics driver and rebooting the computer, the display
is in extended mode. Please click hot key <Ctrl+Alt+F1> to switch
display back to single mode.
Connectors
Connector Description
CN1 Digital I/O Port
CN2 COM2 Connector (NANO830 only)
CN3 COM1 Connector
CN4 LVDS Connector
CN5 Inverter Connector
CN6 Front Panel Connector
CN7 PCI-Express Mini Card Connector
CN8 Power Output Connector
CN9 CPU Fan Connector
CN10 SMBus Connector
CN11 USB Port 4 and 5 Connector
CN12 Ethernet Port 1, USB Port 0 and 1 Stack
CN13 Ethernet Port 2, USB Port 2 and 3 Stack
CN14 VGA Connector
CN16 Audio Jack
CN17 DC Jack Power Connector
CN18 DisplayPort Connector (NANO830 only)
CN19 COM2 Connector (NANO831 only)
SATA1 Serial ATA Connector
SSCFAST1 CFastTM Socket
SDIMM1 DDR3 SO-DIMM Connector
NANO830/831 Intel®AtomTM D2550/N2600 Processor Nano-ITX Board

2 9418K830000E
©Copyright 2012 Axiomtek Co., Ltd.
Version A1 December 2012
Printed in Taiwan
Jumper Settings
Before applying power to the NANO830/831, please make sure all of the
jumpers are in factory default position.
Jumper Description Setting
JP1 LVDS Voltage Selection
Default: +3.3V level 1-2 Close
JP2 COM1 RS-232/422/485 Mode Setting
Default: RS-232
3-5, 4-6 Close
JP3 3-5, 4-6 Close
JP4 1-2 Close
JP5
COM2 Data/Power Selection
(NANO830 only)
Default: RS-232 Data
CN2 Pin 1: DCD 3-5 Close
CN2 Pin 8: RI 4-6 Close
COM2 Data/Power Selection
(NANO831 only)
Default: RS-232 Data
CN19 Pin 1: DCD 3-5 Close
CN19 Pin 9: RI 4-6 Close
JP6 COM1 Data/Power Selection
Default: RS-232 Data CN3 Pin 1: DCD 3-5 Close
CN3 Pin 8: RI 4-6 Close
JP8 LVDS Brightness Control Mode Setting
Default: PWM Mode 1-2 Close
JP9 Restore BIOS Optimal Defaults
Default: Normal Operation 1-2 Close
JP10 Auto Power On
Default: Disable Close
Board Layout
NANO830
Side View NANO831 Side View
9418K830000E 3
©Copyright 2012 Axiomtek Co., Ltd.
Version A1 December 2012
Printed in Taiwan
Top View
NANO830 – Side View
NANO831 – Side View