AXIOMTEK SBC84600 Series User manual

SBC84600 Series Quick Installation Guide
©Copyright 2005 AXIOMTEK Co., Ltd.
Version A7 September 2005
Printed in Taiwan
94284600060E
1
I. Checklist

SBC84600 Board x 1

Quick Installation Guide x 1

Product Information CD-ROM x 1

2-pin jumper cap, Pitch=2.54mm x 5

2-pin jumper cap, Pitch=2.0mm x 10

3mm screw nuts x 2

PS/2 Keyboard/Mouse adapter x 1

2.5” & 3.5” HDD cable x 1

Power Cable 8 Pin x 1

COM+Printer extension cables
with bracket, Pitch=2.0mm x 1

COM extension cables with
bracket, Pitch=2.0mm x 1

FPC cable for extra display
features x 2

Audio Cable x 1 (for
SBC84600VEA Series
Products only)
If there are damaged or missing parts, contact your supplier
and/or dealer immediately. Do not attempt to apply power to
the board if there is damage to any of its components.
Note: The Windows XP Pro/home SP2 edition is not
supported by VIA non-Nehemiah core version processors
which are adopted by SBC84600VEA/VE-400 and
SBC84600VEA/VE-800. For more information please
reference http://support.microsoft.com/kb/893356
II. Jumper Settings
Before turning on the power to the SBC84600 Series,
please make sure that all jumpers are on their default
settings as listed on the table below.
Jumper Default Setting Jumper Setting
JP1 Watchdog Trigger Mode: Disabled Open
JP2 Flat Panel Power Selection: VDDM at 5V Short 1-2
JP3 Clear CMOS Setting: Norma Short 1-2
JP4 COM2 Port Setting: RS-232 Short 1-2
JP5 COM2 Port Setting: RS-232 Short 3-5, 4-6
JP6 COM2 Port Setting: RS-232 Short 3-5, 4-6
JP7 Power Supply Selection: AT power supply Short 1-2
JP8 COM1 Signal/+5V Selection
Default: COM Signal Short 2-3
JP9 COM2 Signal/+5V Selection
Default: COM Signal Short 2-3
Please refer to the Product Information CD for the complete version of the User’s Manual,
drivers, and utilities for the SBC84600 Series CPU Card.

SBC84600 Series Quick Installation Guide
©Copyright 2005 AXIOMTEK Co., Ltd.
Version A7 September 2005
Printed in Taiwan
94284600060E
2
JP10 COM4 Signal/+5V Selection
Default: COM Signal Short 2-3
JP11 COM3 Signal/+5V Selection
Default: COM Signal Short 2-3
JP12 Compact Flash Voltage Selection
Default: 3.3V Short 1-2
III. SBC84600 Connectors
Connectors Label Connectors Label
44 Pin IDE Connector CN1 TV Connector CN14
44-pin LCD Connector CN2 FDD Connector CN15
Flat Panel Bezel Connector CN3 USB connector USB1, USB2
20-pin LCD Connector CN4 VGA CRT Connector VGA1
CPU FAN +5V Connector CN5 Ethernet Connector LAN1
Printer Port Connector CN7 PC/104 Connector J1, J2
Digital I/O Port Connector CN8 COM Connector COM1
ATX Power On/Off Button CN9 COM Connector COM2
Power Input Connectors CN10 COM Connector COM3
IrDA Connector CN11 COM Connector COM4
AC97 Link Interface CN12 Compact Flash Connector CF1
Keyboard and Mouse
Connector CN13 VIDEO Connector VIDEO1
Temperature sensor JP17
IV. AX93102 Connector
Connectors Label Connectors Label
CD AUDIO INPUT CN2 AUDIO PHONE JACK CON1
For SBC84600VEA series products only.
The complete version of the User’s Manual, along with the drivers/utilities software
programs are in the Product Information CD of the SBC84600 Series CPU Card.

SBC84600 Series Quick Installation Guide
©Copyright 2005 AXIOMTEK Co., Ltd.
Version A7 September 2005
Printed in Taiwan
94284600060E
3
V. Additional Information
User’s Manual and other documents are in
Acrobat PDF format. The Product Information
CD contains the Adobe Acrobat 3.0 Reader
installation software for user’s convenience.
VI. Board Layout
The complete version of the User’s Manual, along with the drivers/utilities software
programs are in the Product Information CD of the SBC84600 Series CPU Card.

SBC84600 Series Quick Installation Guide
©Copyright 2005 AXIOMTEK Co., Ltd.
Version A7 September 2005
Printed in Taiwan
94284600060E
4
VII Installation Procedures
Please follow the steps below to install the SBC84600 onto a
chassis:
1. Remove the pillar (a) from the SBC84600 as shown in
Figure 1.
Figure 1.
2. Screw the pillar (a) removed from the SBC84600 and
another three pillars (c), which have same height with
the pillar (a), to the chassis as shown in the Figure 2.
3. Use the bolt (b) on the SBC84600 module to screw
the module with the pillar (a) on the chassis.
The complete version of the User’s Manual, along with the drivers/utilities software
programs are in the Product Information CD of the SBC84600 Series CPU Card.
(a)

SBC84600 Series Quick Installation Guide
©Copyright 2005 AXIOMTEK Co., Ltd.
Version A7 September 2005
Printed in Taiwan
94284600060E
5
4. Screw three proper bolts (d) to the other three pillars
(c) to secure the board with the chassis.
Figure 2.
(c)
(b)
(a)
(d)
The complete version of the User’s Manual, along with the drivers/utilities software
programs are in the Product Information CD of the SBC84600 Series CPU Card.

SBC84600 Series Quick Installation Guide
©Copyright 2005 AXIOMTEK Co., Ltd.
Version A7 September 2005
Printed in Taiwan
94284600060E
6
5. If the Audio kit, AX93102, is used, plug the 10-pin
female box-header of the AX93102 onto the 10-pin
male box-header of the SBC84600 as shown on
Figure 3.
6. Make sure the spacer support (e) fit into the hole (f)
on the SBC84600.
(
e
)
(
f
)
AX93102
10-pin female
box-header
10-pin male
box-header
The complete version of the User’s Manual, along with the drivers/utilities software
programs are in the Product Information CD of the SBC84600 Series CPU Card.