AXIOMTEK MANO882 series User manual

MANO882 Series
Intel®Socket 1150 Xeon®E3/ CoreTM
i7/ i5/ i3/ Celeron®Processor Mini
ITX Board with HDMI/ VGA/ LVDS/
DisplayPort
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
Copyright 2014 Axiomtek Co., Ltd.
All Rights Reserved
September 2014, Version A1
Printed in Taiwan

iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity. To prevent chipsets
from electrostatic discharge damage, please take care of the following jobs with precautions:
Do not remove boards or integrated circuits from their anti-static packaging until you are
ready to install them.
Before holding the board or integrated circuit, touch an unpainted portion of the system
unit chassis for a few seconds. It discharges static electricity from your body.
Wear a wrist-grounding strap, available from most electronic component stores, when
handling boards and components.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
AMI is a trademark of American Megatrend Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®is a trademark of Intel Corporation.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
ESD Precautions...........................................................................................iii
Chapter 1 Introduction............................................. 1
1.1 Features...............................................................................................1
1.2 Specifications......................................................................................2
1.3 Utilities Supported ..............................................................................3
Chapter 2 Board and Pin Assignments.................... 5
2.1 Board Dimensions and Fixing Holes.................................................5
2.2 Board Layout.......................................................................................7
2.3 Jumper Settings..................................................................................8
2.3.1 Audio Output Selection (JP1)...................................................................... 9
2.3.2 COM2 and COM1 Data/Power Selection (JP2 and JP3)............................ 9
2.3.3 Restore BIOS Optimal Defaults (JP5)......................................................... 9
2.3.4 LVDS Brightness Control Mode Setting (JP6) ............................................ 9
2.3.5 LVDS +12V Voltage Selection (JP7) (Optional) ........................................ 10
2.3.6 LVDS +3.3V/+5V Voltage Selection (JP8)................................................. 10
2.3.7 Auto Power On (JP9) ................................................................................ 10
2.3.8 PCI-Express Bifurcation Setting (JP10).................................................... 10
2.4Connectors........................................................................................11
2.4.1 Audio Jack (CN1)...................................................................................... 12
2.4.2 DisplayPort Connector (CN2).................................................................... 12
2.4.3 COM1 and COM2 Connector (CN3) ......................................................... 13
2.4.4 Internal PS/2 Keyboard and Mouse Connector (CN4).............................. 13
2.4.5 VGA Connector (CN5)............................................................................... 13
2.4.6 LAN and USB Connectors (CN6 and CN7) .............................................. 14
2.4.7 HDMI Connector (CN8)............................................................................. 15
2.4.8 SIM Card Slot (CN10) ............................................................................... 15
2.4.9 Full-size PCI-Express Mini Card and mSATA Connector (CN11) ............. 16
2.4.10Internal USB 3.0 Connector (CN12).......................................................... 17
2.4.11 ATX Power Connectors (CN13 and ATX2)................................................ 17
2.4.12 Internal USB 2.0 Connectors (CN14 and CN17) ...................................... 18
2.4.13 Digital I/O Connector (CN16) .................................................................... 18
2.4.14 Inverter Connector (CN18)........................................................................ 18
2.4.15 LVDS Connector (CN19)........................................................................... 19
2.4.16 Front Panel Connector (CN20) ................................................................. 21
2.4.17 Internal COM Connectors (COM3~COM6)............................................... 22
2.4.18 FAN Connectors (FAN1 and FAN2) .......................................................... 22

v
2.4.19 SATA 3.0 Connectors (SATA1~SATA4)..................................................... 23
Chapter 3 Hardware Installation ........................... 25
3.1 Installing the Processor....................................................................25
3.2 Installing the Memory .......................................................................31
Chapter 4 Hardware Description ........................... 33
4.1 Microprocessors ...............................................................................33
4.2 BIOS ...................................................................................................33
4.3 System Memory.................................................................................33
4.4 I/O Port Address Map........................................................................34
4.5 Interrupt Controller (IRQ) Map .........................................................36
4.6 Memory Map ......................................................................................39
Chapter 5 AMI BIOS Setup Utility .......................... 41
5.1 Starting...............................................................................................41
5.2 Navigation Keys ................................................................................41
5.3 Main Menu..........................................................................................43
5.4 Advanced Menu.................................................................................44
5.5 Chipset Menu.....................................................................................55
5.6 Boot Menu..........................................................................................61
5.7 Security Menu....................................................................................62
5.8 Save & Exit Menu ..............................................................................63
5.9 Event Logs.........................................................................................65
Appendix A Watchdog Timer................................... 69
About Watchdog Timer................................................................................69
How to Use Watchdog Timer.......................................................................69
Appendix B Digital I/O ............................................. 71
Digital I/O Software Programming..............................................................71
Appendix C Configuring SATA for RAID .................. 73
Configuring SATA Hard Drive(s) for RAID Function..................................73
Appendix D iAMT Settings ...................................... 81
Entering MEBx .............................................................................................81
Set and Change Password..........................................................................81

vi
iAMT Settings...............................................................................................83
iAMT Web Console ......................................................................................86

MANO882 Series Mini ITX Board
Introduction 1
Chapter 1
Introduction
The MANO882 with C226 is a Mini ITX board based on Intel®Xeon®E3/ CoreTM i7/ i5/ i3 and
Celeron®desktop processors in LGA1150 socket; supporting 22nm technology. The board
integrates Intel®C226 chipset that delivers outstanding system performance through
high-bandwidth interfaces, multiple I/O functions for interactive applications and various
embedded computing solutions. There are two 204-pin DDR3 SO-DIMM sockets for dual
channel DDR3 1600/1333MHz memory with maximum capacity up to 16GB; assuming dual
channel mode of two 8GB double-sided unbuffered, non-ECC SO-DIMM memory configuration.
The board also features Gigabit Ethernet, four SATA3.0 ports (support SATARAID 0/1/5/10 by
C226) at maximum transfer rate up to 6Gb/s, four USB 3.0 and six USB 2.0 high speed
compliant ports that can achieve the best stability and reliability for industrial applications.
1.1 Features
LGA1150 socket 4th Generation Intel®Xeon®E3/ CoreTM i7 /i5 /i3 /Celeron®processors
2 DDR3 1600/1333MHz up to 16GB
PCI-Express Gen. 3 supported
4 SATA-600 with RAID 0, 1, 5 and 10 supported
4 USB 3.0 supported
iAMT 9.0 supported
TPM 1.2 supported
Triple view display

MANO882 Series Mini ITX Board
2 Introduction
1.2 Specifications
CPU
Intel®Xeon®E3/ CoreTM i7/ i5/ i3/ Celeron®desktop processors.
System Chipset
Intel®C226.
CPU Socket
LGA1150 socket.
BIOS
AMI BIOS via SPI interface with socket.
System Memory
Two 204-pin unbuffered DDR3 SO-DIMM sockets.
Maximum up to 16GB DDR3 1600/1333MHz memory with two SO-DIMMs using
8GB memory technology.
Onboard Multi I/O
Controller: Nuvoton NCT6106D.
Serial ports: Four RS-232 ports (COM3/4/5/6) and two RS-232/422/485 ports
(COM1/2).
Serial ATA
Four SATA 3.0 ports (6Gb/s performance) with SATA RAID 0/1/5/10.
USB Interface
Four USB 3.0 ports with fuse protection.
Six USB 2.0 ports with fuse protection.
Display
One HDMI.
One LVDS 18/24-bit single/dual channel.
One VGA.
One DisplayPort.
Watchdog Timer
1~255 seconds; up to 255 levels.
Expansion Interface
One PCI-Express x16 slot.
Ethernet
LAN1 –Intel®I217LM supports 1000/100/10Mbps.
LAN2 –Intel®i210AT supports 1000/100/10Mbps.
Audio
HD audio compliant (with line/speaker-out and MIC-in) via ALC662.
Speaker-out with 1W/8Ωx2.

MANO882 Series Mini ITX Board
Introduction 3
Power Management
ACPI (Advanced Configuration and Power Interface).
Form Factor
Mini ITX form factor.
Note
1. All specifications and images are subject to change without notice.
2. The PCI-Express x16 slot supports riser card with up to 2 PCI-Express x8.
1.3 Utilities Supported
Chipset driver
Ethernet driver
Graphics driver
Audio driver
Intel®USB 3.0 driver
RAID utility
iAMT utility and driver

MANO882 Series Mini ITX Board
4 Introduction
This page is intentionally left blank.

MANO882 Series Mini ITX Board
Board and Pin Assignments 5
Chapter 2
Board and Pin Assignments
2.1 Board Dimensions and Fixing Holes
Top View

MANO882 Series Mini ITX Board
6 Board and Pin Assignments
Bottom View
I/O Bracket

MANO882 Series Mini ITX Board
Board and Pin Assignments 7
2.2 Board Layout
Top View
I/O Bracket

MANO882 Series Mini ITX Board
8 Board and Pin Assignments
2.3 Jumper Settings
Jumper is a small component consisting of jumper clip and jumper pins. Install jumper clip on 2
jumper pins to close. And remove jumper clip from 2 jumper pins to open. The following
illustration shows how to set up jumper.
Before applying power to MANO882 Series, please make sure all of the jumpers are in factory
default position. Below you can find a summary table and onboard default settings.
Note
Once the default jumper setting needs to be changed, please do it under power-off
condition.
Jumper
Description
Setting
JP1
Audio Output Selection
Default: Line-out
1-3, 2-4 Close
JP2
COM2 Data/Power Selection
Default: RS-232 Data
CN3B Pin 1: DCD
3-5 Close
CN3B Pin 9: RI
4-6 Close
JP3
COM1 Data/Power Selection
Default: RS-232 Data
CN3A Pin 1: DCD
3-5 Close
CN3A Pin 9: RI
4-6 Close
JP5
Restore BIOS Optimal Defaults
Default: Normal Operation
1-2 Close
JP6
LVDS Brightness Control Mode Setting
Default: PWM Mode
1-2 Close
JP7 (Optional)
LVDS +12V Voltage Selection
Default: NA
1-2 Open
JP8
LVDS Voltage Selection
Default: +3.3V level
1-2 Close
JP9
Auto Power On
Default: Disable
1-2 Close
JP10
PCI-Express Bifurcation Setting
Default: One x16 PCI-Express
1-2 Close

MANO882 Series Mini ITX Board
Board and Pin Assignments 9
2.3.1 Audio Output Selection (JP1)
Use this jumper to select line-out or speaker-out as source of audio output on audio
connector. When speaker-out is used, it delivers 1W/channel continuous at 8Ω loads.
2.3.2 COM2 and COM1 Data/Power Selection (JP2 and JP3)
The COM2/COM1 port has +5V level power capability on DCD and +12V level on RI by
setting jumper JP2/JP3. When this port is set to +5V or +12V level, please make sure its
communication mode is RS-232. You can change the communication mode
(RS-232/422/485) via BIOS setting, see section 5.4.
JP2
JP3
2.3.3 Restore BIOS Optimal Defaults (JP5)
Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing this
procedure can restore BIOS optimal defaults.
2.3.4 LVDS Brightness Control Mode Setting (JP6)
This jumper enables you to select PWM or voltage control mode for inverter connector
(CN18). These two control modes are for adjusting the brightness of LVDS panel.
Function
Setting
Line-out (Default)
1-3, 2-4 close
Speaker-out (w/ amplifier)
3-5, 4-6 close
Function
JP2 Setting
Power: Set CN3B pin 1 to +5V level
1-3 close
Data: Set CN3B pin 1 to DCD (Default)
3-5 close
Power: Set CN3B pin 9 to +12V level
2-4 close
Data: Set CN3B pin 9 to RI (Default)
4-6 close
Function
JP3 Setting
Power: Set CN3A pin 1 to +5V level
1-3 close
Data: Set CN3A pin 1 to DCD (Default)
3-5 close
Power: Set CN3A pin 9 to +12V level
2-4 close
Data: Set CN3A pin 9 to RI (Default)
4-6 close
Function
Setting
Normal operation (Default)
1-2 close
Restore BIOS optimal defaults
2-3 close
Function
Setting
PWM mode (Default)
1-2 close
Voltage mode
3-4 close

MANO882 Series Mini ITX Board
10 Board and Pin Assignments
2.3.5 LVDS +12V Voltage Selection (JP7) (Optional)
The board supports voltage selection for flat panel displays. Use JP7 to set LVDS
connector (CN19) pin 1~6 VCCM to +12V level. To prevent hardware damage, before
connecting please make sure that the input voltage of flat panel is correct.
2.3.6 LVDS +3.3V/+5V Voltage Selection (JP8)
The board supports voltage selection for flat panel displays. Use JP8 to set LVDS
connector (CN19) pin 1~6 VCCM to +3.3V or +5V. To prevent hardware damage, before
connecting please make sure that the input voltage of flat panel is correct.
2.3.7 Auto Power On (JP9)
If this jumper is enabled for power input, the system will be automatically power on
without pressing soft power button. If this jumper is disabled for power input, it is
necessary to manually press soft power button to power on the system.
Note
This function is similar to the feature of power on after power failure,
which is controlled by hardware circuitry instead of BIOS.
2.3.8 PCI-Express Bifurcation Setting (JP10)
JP10 is for PCI-Express bifurcation setting. See table below for detailed information.
Function
Setting
+12V level
1-2 close
NA (Default)
1-2 open
Function
Setting
+3.3V (Default)
1-2 close
+5V
2-3 close
Function
Setting
Disable auto power on (Default)
1-2 close
Enable auto power on
2-3 close
Function
Setting
Set CN15 to one x16 PCI-Express (Default)
1-2 close
Set CN15 to two x8 PCI-Express
2-3 close

MANO882 Series Mini ITX Board
Board and Pin Assignments 11
2.4 Connectors
Signals go to other parts of the system through connectors. Loose or improper connection
might cause problems, please make sure all connectors are properly and firmly connected.
Here is a summary table which shows all connectors on the hardware.
Connector
Description
CN1
Audio Jack
CN2
DisplayPort Connector
CN3
COM1 Connector (CN3A) and COM2 Connector (CN3B)
CN4
Internal PS/2 Keyboard and Mouse Connector
CN5
VGA Connector
CN6
LAN2 and USB 2.0 Port 1, 2
CN7
LAN1 and USB 3.0 Port 1, 2
CN8
HDMI Connector
CN10
SIM Card Slot
CN11
Full-size PCI-Express Mini Card and mSATA Connector
CN12
Internal USB 3.0 Port 3 and 4
CN13
24-pin ATX Power Connector
CN14
Internal USB 2.0 Port 3 and 4
CN15
PCI-Express x16 Slot
CN16
Digital I/O Connector
CN17
Internal USB 2.0 Port 5 and 6
CN18
Inverter Connector
CN19
LVDS Connector
CN20
Front Panel Connector
ATX2
8-pin +12V ATX Power Connector
COM3~COM6
Internal COM3~COM6 Connectors
FAN1
System Fan Connector
FAN2
CPU Fan Connector
SATA1~SATA4
SATA 3.0 Connectors
DIMM1~DIMM2
DDR3 SO-DIMM Connectors

MANO882 Series Mini ITX Board
12 Board and Pin Assignments
2.4.1 Audio Jack (CN1)
The board provides HD audio jack on the rear I/O. Install audio driver, and then attach
audio devices to CN1.
2.4.2 DisplayPort Connector (CN2)
The DisplayPort interface is available through CN2.
Pin Color
Signal
Green
Line-out
Pink
MIC-in
Pin
Signal
1
DPB_LANE0
2
GND
3
DPB_LANE0#
4
DPB_LANE1
5
GND
6
DPB_LANE1#
7
DPB_LANE2
8
GND
9
DPB_LANE2#
10
DPB_LANE3
11
GND
12
DPB_LANE3#
13
Detect Pin
14
GND
15
DPB_AUX
16
GND
17
DPB_AUX#
18
DPB_HPDE
19
GND
20
+3.3V

MANO882 Series Mini ITX Board
Board and Pin Assignments 13
CN3B
CN3A
2.4.3 COM1 and COM2 Connector (CN3)
CN3 is a double-deck DB-9 connector. Both CN3A (for COM1) and CN3B (for COM2)
come with power capability on DCD and RI pins by setting jumpers (see section 2.3.2).
The pin assignments of RS-232/RS-422/RS-485 are listed in table below. If you need
COM1/COM2 port to support RS-422 or RS-485, please refer to section 5.4.
2.4.4 Internal PS/2 Keyboard and Mouse Connector (CN4)
The PS/2 keyboard and mouse interface is available through CN4.
2.4.5 VGA Connector (CN5)
The CN5 is a high rise 15-pin D-Sub connector which is commonly used for VGAmonitor.
This VGA interface configuration can be configured via software utility.
Pin
RS-232
RS-422
RS-485
1
DCD
TX-
Data-
2
RXD
TX+
Data+
3
TXD
RX+
No use
4
DTR
RX-
No use
5
GND
No use
No use
6
DSR
No use
No use
7
RTS
No use
No use
8
CTS
No use
No use
9
RI
No use
No use
Pin
Signal
Pin
Signal
1
KBVCC
2
K/B Data
3
K/B CLK
4
PS2_GND
5
KBVCC
6
KBVCC
7
M/S Data
8
M/S CLK
9
PS2_GND
10
N.C.
Pin
Signal
Pin
Signal
1
Red
2
Green
3
Blue
4
N.C.
5
GND
6
DETECT
7
GND
8
GND
9
VCC
10
GND
11
N.C.
12
DDC DATA
13
Horizontal Sync
14
Vertical Sync
15
DDC CLK

MANO882 Series Mini ITX Board
14 Board and Pin Assignments
CN6
2.4.6 LAN and USB Connectors (CN6 and CN7)
The board comes with two high performance plug and play ethernet interfaces (RJ-45)
which are fully compliant with the IEEE 802.3 standard. Connection can be established
by plugging one end of the ethernet cable into this RJ-45 connector and the other end to
a 1000/100/10-Base-T hub.
The CN6 has lower double-deck connector for USB 2.0 port 1 and 2.
The CN7 has lower double-deck connector for USB 3.0 port 1 and 2.
CN7
Pin
LAN2 Signal
Pin
USB Signal
L1
MDI0+
1
+5V standby power
L2
MDI0-
2
USB D1-
L3
MDI1+
3
USB D1+
L4
MDI1-
4
Ground (GND)
L5
MDI2+
5
+5V standby power
L6
MDI2-
6
USB D2-
L7
MDI3+
7
USB D2+
L8
MDI3-
8
Ground (GND)
A
100 LAN LED (Green)/1000 LAN LED (Orange)
B
Active LED (Yellow)
Pin
LAN1 Signal
Pin
LAN1 Signal
L1
MDI0+
L5
MDI2+
L2
MDI0-
L6
MDI2-
L3
MDI1+
L7
MDI3+
L4
MDI1-
L8
MDI3-
A
100 LAN LED (Green)/1000 LAN LED (Orange)
B
Active LED (Yellow)
Pin
USB Signal
Pin
USB Signal
1
USB_VCC (+5V
standby power)
10
USB_VCC (+5V
standby power)
2
USB_Data0-
11
USB_Data1-
3
USB_Data0+
12
USB_Data1+
4
GND
13
GND
5
SSRX1-
14
SSRX2-
6
SSRX1+
15
SSRX2+
7
GND
16
GND
8
SSTX1-
17
SSTX2-
9
SSTX1+
18
SSTX2+