AXIOMTEK SBC86832 Series User manual

SBC86832 Series
Intel®Core™ 2 Duo All-In-One
Mini ITX Board
With DVI-I/LCD
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain
accurate information. AXIOMTEK Co., Ltd. assumes no responsibility
for any infringements of patents or any third party’s rights, and any
liability arising from such use.
AXIOMTEK does not warrant or assume any legal liability or
responsibility for the accuracy, completeness or usefulness of any
information in this document. AXIOMTEK does not make any
commitment to update the information in this manual.
AXIOMTEK reserves the right to change or revise this document
and/or product at any time without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of AXIOMTEK Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is
recommended by the manufacturer that you follow the manufacturer’s
instructions to only replace the same or equivalent type of battery,
and dispose of used ones.
©Copyright 2007 AXIOMTEK Co., Ltd.
All Rights Reserved
July 2007, Version A2
Printed in Taiwan

iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity.
To prevent chipsets from electrostatic discharge damage, please take
care of the following jobs with precautions:
Do not remove boards or integrated circuits from their anti-static
packaging until you are ready to install them.
Before holding the board or integrated circuit, touch an unpainted
portion of the system unit chassis for a few seconds. It
discharges static electricity from your body.
Wear a wrist-grounding strap, available from most electronic
component stores, when handling boards and components.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
Phoenix & AWARD are trademarks of Phoenix Technology Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International Business
Machines Corporation.
Intel®and Pentium®are trademarks of Intel Corporation.
Winbond is a trademark of Winbond Electronics Corp.
Other brand names and trademarks are the properties and registered
brands of their respective owners.

iv
Table of Contents
Disclaimers ................................................................................. ii
ESD Precautions........................................................................ iii
Chapter 1 Introduction.................................................................... 1
1.1 Specifications ................................................................... 2
1.2 Utilities Supported ............................................................ 4
Chapter 2 Jumpers and Connectors ............................................. 5
2.1 Board Layout and Fixing Holes ........................................ 5
2.2 Placement......................................................................... 7
2.3 Jumper Settings................................................................ 9
2.3.1 COM1 Mode Select Jumper..................................... 10
2.3.2 COM1 Mode Select Jumper..................................... 10
2.3.3 COM1 Mode Select Jumper..................................... 10
2.3.4 COM2~COM4 Mode Select for Type Jumpers........ 11
2.3.5 CPU Frequency Select Jumpers.............................. 11
2.3.6 LVDS Voltage Selection Jumper.............................. 12
2.3.7 CMOS Clear Jumper................................................ 12
2.3.8 TPM PP(Physical Presence) Select Jumper............ 12
2.3.9 Compact Flash Setting Jumper................................ 12
2.3.10 Compact Flash Voltage Select Jumper.................... 12
2.3.11 USB Power Select Jumpers..................................... 13
2.4 Connectors..................................................................... 13
2.4.1 Print Port or Floppy Connector................................. 14
2.4.2 COM2~COM4 Port Connectors................................ 15
2.4.3 Digital I/O Port (DIO) Connector............................... 15
2.4.4 VGA & COM1 Connector.......................................... 16
2.4.5 LVDS Backlight Connector....................................... 17
2.4.6 LAN *2 Connector..................................................... 17
2.4.7 USB*2+IEEE1394 Connectors ................................. 18
2.4.8 LVDS Flat Panel Connector...................................... 19
2.4.9 SATA Connectors..................................................... 20
2.4.10 Audio Phone Jack Connector................................... 20
2.4.11 USB Connectors....................................................... 20
2.4.12 Parallel IDE Connector ............................................. 21
2.4.13 Flat Panel Bezel Connector...................................... 22
2.4.14 Internal Audio Connector.......................................... 23
2.4. 15 ATX Power Connector.............................................. 23
2.4.16 +12V ATX Power Connector .................................... 23

v
2.4.17 SMBUS Connector ................................................... 24
2.4.18 Keyboard and PS/2 Mouse Connector..................... 24
Chapter 3 Hardware Description.................................................. 25
3.1 Microprocessors ............................................................. 25
3.2 BIOS............................................................................... 25
3.3 System Memory.............................................................. 25
3.4 I/O Port Address Map..................................................... 26
3.5 Interrupt Controller.......................................................... 27
Chapter 4 Award BIOS Utility....................................................... 29
4.1 Entering Setup................................................................ 29
4.2 Control Keys................................................................... 30
4.3 Getting Help.................................................................... 30
4.4 The Main Menu............................................................... 31
4.5 Standard CMOS Setup Menu......................................... 32
4.6 Advanced BIOS Features............................................... 35
4.7 Advanced Chipset Features........................................... 39
4.8 Integrated Peripherals.................................................... 41
4.9 Power Management Setup............................................. 45
4.10 PnP/PCI Configuration Setup......................................... 48
4.11 PC Health Status............................................................ 49
4.12 Frequency/Voltage Control............................................. 50
4.13 Load Optimized Defaults................................................ 51
4.14 Set Supervisor/User Password ...................................... 52
4.15 Save & Exit Setup........................................................... 53
4.16 Exit Without Saving ........................................................ 54
Appendix A..................................................................................... 56
Appendix B..................................................................................... 58

vi
MEMO

SBC86832 Series All-In-One Mini ITX Board User’s Manual
Introduction 1
C h a p t e r 1
Introduction
The SBC86832, a Mini ITX board, supports Intel®Core™2 Duo,
Core™Duo, Core™Solo and Celeron®M processors with graphics,
audio, and Gigabit Ethernet interfaces. It is practically finest
embedded Socket M board in the market. It integrates LPC I/Os,
UXGA, LCD, Ethernet and audio to make all in one single board.
Additionally, it provides you with unique embedded features, such as
4 serial ports (3 x RS-232 and 1 x RS-232/422/485) and Mini ITX form
factor that applies an extensive array of PC peripherals. This
industrial-grade board can achieve the best stability and reliability that
makes your system perform the most endurable operation in any
critical environments. The built-in Watchdog Timer has enhanced the
system reliability that achieves a unique feature to distinguish itself
from other boards.
Designed for the professional embedded developers, the
Socket M embedded board SBC86832 Series is virtually ultimate one-
step solution for embedded system applications.

SBC86832 Series All-In-One Mini ITX Board User’s Manual
Introduction
2
1.1 Specifications
zCPU: Socket M for Intel®Core™2 Duo, Core™Duo,
Core™Solo and Celeron®M processors
zSystem Chipset: Intel®945GME & ICH7M
zCPU Frequency: 533/667MHz FSB
zBIOS
Phoenix-Award BIOS, Y2K compliant
4Mbit Flash, DMI, Plug and Play
PXE Ethernet Boot ROM
SmartView for multiple LCD type selection, display
mode option and application extension features
RPL/PXE Ethernet Boot ROM
“Load Optimized Default” to backup customized Setting in
the BIOS flash chip to prevent from CMOS battery fail
zSystem Memory
Two x 240-pin DDR2 DIMM sockets
Maximum to 3GB DDR2 memory
zL2 Cache: integrated in CPU
zOnboard IDE
One PATA-100 with 40-pin box-header
PATA-100 as PIO Mode 0-4, DMA Mode 0-2 and Ultra
DMA/33/66/100
Two SATA-150 connectors
zCompact Flash Socket
One Compact Flash Type II Socket (optional)
zOnboard Multi-I/O
One 26-pin box-header for shared FDD/LPT
3 x RS-232, 1x RS-232/422/485
zUSB Interface
Eight USB ports with fuse protection and complies with
USB Spec. Rev. 2.0

SBC86832 Series All-In-One Mini ITX Board User’s Manual
Introduction 3
zWatchdog Timer:
1~255 seconds; up to 255 levels
zGraphics:
Intel® 945GME GMCH Gen 3.5 integrated graphic engine
DVI-I interface for both CRT and DVI external display
devices
Maximum up to 224MB frame buffer sharing system
memory
Maximum display resolution:
CRT: 2048 x1536
LVDS: 1600 X1200 (24-bit single/dual
channel LVDS interface)
DVI: 1600 X 1200
LCD backlight control supported
zExpansion Slot:
PCI slot for 2 Bus master 32-bit expansion
PCI Express Mini Card (optional)
zEthernet:
Two RTL8111B Gigabit Ethernet
Wake On LAN (via ATX power supply)
Equipped with RJ-45 interface
zAudio:
Realtek AC’97 codec audio
MIC-in, Line-out
zPower Management:
ACPI (Advanced Configuration and Power Interface)
zForm Factor:
Mini ITX form factor
NOTE: All specifications and images are subject to change
without notice.

SBC86832 Series All-In-One Mini ITX Board User’s Manual
Introduction
4
1.2 Utilities Supported
zChipset Driver
zVGA Driver
zEthernet Driver
zAudio Driver

SBC86832 Series All-In-One Mini ITX Board User’s Manual
Jumpers and Connectors 5
C h a p t e r 2
Jumpers and Connectors
2.1 Board Layout and Fixing Holes
Component Side

SBC86832 Series All-In-One Mini ITX Board User’s Manual
Jumpers and Connectors
6
Solder Side

SBC86832 Series All-In-One Mini ITX Board User’s Manual
Jumpers and Connectors 7
2.2 Placement
Component Side

SBC86832 Series All-In-One Mini ITX Board User’s Manual
Jumpers and Connectors
8
Solder Side

SBC86832 Series All-In-One Mini ITX Board User’s Manual
Jumpers and Connectors 9
2.3 Jumper Settings
Proper jumer settings configure the SBC86832 to meet your
application purpose. We are herewith listing a summary table of all
jumpers and default settings for onboard devices, respectively.
Here is a list of jumper settings：
Jumper Default Setting Jumper Setting
JP1 COM1 Mode Select
Default: RS-232 Short 1-2
JP2 COM1 Mode Select
Default: RS-232 Short 3-5,4-6
JP3 COM1 Mode Select
Default: RS-232 Short 3-5,4-6
COM2 Pin 1: DCD Short 7-9JP4 COM2 Mode Select COM2 Pin 8: RI Short 8-10
COM3 Pin 1: DCD Short 7-9JP5 COM3 Mode Select COM3 Pin 8: RI Short 8-10
COM4 Pin 1: DCD Short 7-9JP6 COM4 Mode Select COM4 Pin 8: RI Short 8-10
COM1 Pin 1: DCD Short 7-9JP7 COM1 Mode Select COM1 Pin 9: RI Short 8-10
JP8 CPU Frequency Select: Auto Short 1-2
JP9 CPU Frequency Select: Auto Short 1-2
JP10 CPU Frequency Select: Auto Short 1-2
JP11 LCD Voltage Select
Default: 3.3V Short 1-2
JP14 Normal Operation/Clear CMOS setting
Default: Normal Operation Short 1-2
JP15 TPM Function Short 1-2
JP16 Compact Flash Setting Short 1-2
JP17 Compact Flash Voltage Select Short 1-2
JP18 USB Voltage Select Short 2-3

SBC86832 Series All-In-One Mini ITX Board User’s Manual
Jumpers and Connectors
10
Jumper Default Setting Jumper Setting
JP19 USB Voltage Select Short 2-3
JP20 USB Voltage Select Short 1-2
JP21 USB Voltage Select Short 1-2
-- End of Jumper Settings Table --
2.3.1 COM1 Mode Select Jumper: JP1
These jumpers select the COM1 port’s communication mode to
operate RS-232 or RS-422/485.
Options Settings
RS-232 Short 1-2 (default)
RS-422 Short 3-4
RS-485 Short 5-6,7-8
JP1
1
3
5
7
2
4
6
8
2.3.2 COM1 Mode Select Jumper: JP2
Options Settings
RS-485 Short 1-3,2-4
RS-232 Short 3-5,4-6(default)
JP2
2
4
6
1
3
5
2.3.3 COM1 Mode Select Jumper: JP3
Options Settings
RS-485 Short 1-3,2-4
RS-232 Short 3-5,4-6(default)
JP3
2
4
6
1
3
5

SBC86832 Series All-In-One Mini ITX Board User’s Manual
Jumpers and Connectors 11
2.3.4 COM1~COM4 Mode Select for Type Jumpers: JP4,
JP5, JP6, JP7
These jumpers select the COM1, COM2, COM3, COM4 ports’
communication mode to operate RS-232 or RS-422/485.
COM1 (CN7) JP7 COM2 (CN2) JP4
Pin 1=12V Short 1-3 Pin 1=12V Short 1-3
Pin 1=5V Short 3-5 or 5-7 Pin 1=5V Short 3-5 or 5-7
Pin 1=DCD Short 7-9 Pin 1=DCD Short 7-9
Pin 9=12V Short 2-4 Pin 8=12V Short 2-4
Pin 9=5V Short 4-6 or 6-8 Pin 8=5V Short 4-6 or 6-8
Pin 9=RI Short 8-10 Pin 8=RI Short 8-10
COM3 (CN3) JP5 COM4 (CN4) JP6
Pin 1=12V Short 1-3 Pin 1=12V Short 1-3
Pin 1=5V Short 3-5 or 5-7 Pin 1=5V Short 3-5 or 5-7
Pin 1=DCD Short 7-9 Pin 1=DCD Short 7-9
Pin 8=12V Short 2-4 Pin 8=12V Short 2-4
Pin 8=5V Short 4-6 or 6-8 Pin 8=5V Short 4-6 or 6-8
Pin 8=RI Short 8-10 Pin 8=RI Short 8-10
JP4, JP5, JP6, JP7
2.3.5 CPU Frequency Select Jumpers: JP8.JP9.JP10
This jumper helps you set the CPU frequency.
Options JP8 JP9 JP10
Auto Select Short 1-2
[default] Short 1-2 [default] Short 1-2 [default]
533MHz Short 2-3 Short 2-3 Short 2-3
667MHz Short 2-3 OPEN Short 2-3
JP8, JP9,
JP10
9
7
5
3
1
10
8
6
4
2

SBC86832 Series All-In-One Mini ITX Board User’s Manual
Jumpers and Connectors
12
2.3.6 LVDS Voltage Selection Jumper: JP11
This jumper is to select the voltage for LVDS interface.
Options Settings
3.3V Short 1-2 (default)
5V Short 2-3
JP11
2.3.7 CMOS Clear Jumper: JP14
You may need to use this jumper is to clear the CMOS memory if
incorrect settings in the Setup Utility.
Options Settings
Normal Short 1-2
(default)
Clear CMOS Short 2-3
JP14
2.3.8 TPM PP(Physical Presence) Select Jumper：JP15
Options Settings
Only Accept
H/W signals. Short 2-3
Accept both
H/W & S/W
signals.
Short 1-
2(default)
JP15
2.3.9 Compact Flash Setting Jumper: JP16
Options Settings
Master Short 2-3
Slave Short 1-
2(default)
JP16
2.3.10 Compact Flash Voltage Select Jumper: JP17
Options Settings
3.3V Short 1-
2(default)
5V Short 2-3
JP16

SBC86832 Series All-In-One Mini ITX Board User’s Manual
Jumpers and Connectors 13
2.3.11 USB Power Select Jumpers: JP18, JP19, JP20,
JP21
Options Settings
5V Standby Short 1-2
5V Short 2-3
JP18, JP19,
JP20, JP21
2.4 Connectors
Connectors connect the CPU card with other parts of the system.
Loose or improper connection might cause problems. Make sure all
connectors are properly and firmly connected. Here is a summary table
shows you all connectors on the SBC86832 Series.
Connectors Label
Printer Port or Floppy Connector
(Default : LPT) CN1
COM2 Connector CN2
COM3 Connector CN3
COM4 Connector CN4
Digital I/O (DIO) Connector CN5
VGA & COM1 Connector CN7
LVDS Backlight Connector CN8
LAN*2 Connector CN9
USB*2+IEEE1394 Connectors CN10, CN13
LVDS Connector CN11
SATA Connectors CN14, CN15
Audio Phone Jack Connector CN16
USB Connectors CN17, CN19
Parallel IDE Connector CN18
Flat Panel Bezel Connector CN20
Internal Audio Connector CN21

SBC86832 Series All-In-One Mini ITX Board User’s Manual
Jumpers and Connectors
14
Connectors Label
ATX Power Connector ATX1
+12V Power Connector ATX2
SMBUS Connector JP13
KB/MS Connector KM1
-- End of Connectors Table --
2.4.1 Print Port or Floppy Connector: CN1
Print Port Connector [Default]
This board has a multi-mode parallel port to support:
1. Standard Mode:
IBM PC/XT, PC/AT and PS/2™are compatible with bi-directional
parallel port.
2. Enhanced Mode:
Enhance parallel port (EPP) is compatible with EPP 1.7 and EPP 1.9
(IEEE 1284 compliant).
3. High Speed Mode:
Microsoft and Hewlett Packard extended capabilities port (ECP) is
IEEE 1284 compliant.
Pin Signal Pin Signal
1 Auto Form
Feed# 2 Strobe#
3 Error# 4 Data 0
5 Initialize# 6 Data 1
7 Printer Select In# 8 Data 2
9 GND 10 Data 3
11 GND 12 Data 4
13 GND 14 Data 5
15 GND 16 Data 6
17 GND 18 Data 7
19 GND 20 Acknowledge#
21 GND 22 Busy
23 GND 24 Paper Empty#
25 NC 26 Printer Select
CN1
2
4
6
1
3
5
78
9
11
13
15
10
12
14
16
17
19
21
23
25
18
20
22
24
26