Axis APS200B User manual

1
KEY FEATURES
•Anti-collision solution for cars, rv’s, trucks, caravans, etc
• For installation in rear bumpers
•2 x 18mm paintable sensors
• Compact, 4-Stage Audible Buzzer - 42 x 16mm
• Compact control box
• 0.3 ~ 1.5m detection range
• Bumper cutter included
• 9 ~ 16V DC Operating Voltage
•20-300mA Operating Current
•-30 ~ 85° C Working Temperature
2WARRANTY
YEAR
MOBILE SAFETY
APS200B
2SENSOR PARKING SYSTEM with
AUDIBLE BUZZER

2
GENERAL INSTALLATION DIAGRAM
A
D

3
90
90
90
Fix the position of sensors. No obstacle should be detected at 90° from the top view otherwise
the system will fasle alarm. .
Installation distance dragram
Best position for 2 sensors Best position for 4 sensors
0.6-0.8m 0.3-0.4m
0.5-0.8m
Installation when vertical to the ground. Installation when bumper is sloping to the ground.
Installation diagram
Installation diagram for sensors with direction markings
up
up
up
up
up
SENSOR INSTALLATION DIAGRAM
Installation diagram distance
0.6-0.8m
Best position for 2 sensors Best position for 4 sensors
0.3-0.4m
0.5-0.8m
Installation when bumper is sloping to the ground. Installation when vertical to the ground.
Installation diagram
Installation diagram for sensors with direction markings
up
up
up
up
up
90
90
90
at 90° from the top view otherwiseNo obstacle should be detected Fix the position of sensors.
the system will false alarm.

4
ABCD
Smooth slope Smooth round objects
Objects that absorb sound
waves: e.g. cotton, wool
Objects hard to detect: including pedestrians with absorbing clothing.
should be under the same line.
B. 0.5-0.8m vertically high to the
ground, 0.55m is recommended.
C. Vertical, tidy surface without
metal components is preferred.
A.Four drill holes A.B.C.D
Smooth slope Smooth round objects Objects absorbing
wave, e.g.cotton
Objects hard to be detected
DISTANCE INDICATION
> 1.5m: ........................................................
1-1.5m: Bi................Bi...............Bi...............
0.5-1m: Bi.......Bi......Bi......Bi......Bi......Bi......
0-0.5m: Continuous Tone
SENSOR DETECTION

5
SELECT DRILLING POSITION FOR SENSORS
SELECT DRILLING POSITION FOR OPTIONAL SENSORS - S56
A. Choose suitable drilling positions
for A and D sensor and mark
sensor 8 - 13cm from the edge.
Preferred distance is 11cm
D
A
AD
AB
A. Measure the distance between
sensor A and D
Divide distance by 3 and mark sensor B & C
For best detection angle, position A & D
A. Choose suitable drilling positions
for A and D sensor and mark
sensor 8 - 13cm from the edge.
Preferred distance is 11cm
D
A
AD
AB
A. Measure the distance between
sensor A and D
Divide distance by 3 and mark sensor B & C
For best detection angle, position A & D
A. Choose suitable drilling positions
for A and D sensor and mark
sensor 8 - 13cm from the edge.
Preferred distance is 11cm
D
A
AD
AB
A. Measure the distance between
sensor A and D
Divide distance by 3 and mark sensor B & C
For best detection angle, position A & D

6
CONTROL BOX INSTALLATION
SENSOR INSTALLATION
OTHERS
2.5m
6. Others
Install control box inside the boot. Keep
away from heat, moisture and vibration.
NOTE: Control box is not waterproof.
Mount the buzzer under the dashboard.

7
INSTALLATION STEPS
NOTE
1. Carefully choose position for sensors
2. Select drilling position for sensor A & D
3. Locate the position and drill
4. Install the sensors and hide the wires
5. Install the buzzer
6. Install the control box (NOTE: The control box is not waterproof)
TEST
1. Adjust the direction and orientation of sensors. Neaten the wiring after
installation.
2. Connect the power wire to the reversing light circuit.
3. Connect the wires between control box and buzzer
4. After starting the car, the buzzer will sound “BiBi” on power up. Insert one
sensor into the control box port. Within 1.0m of the sensor, it should
detect normally.
Disconnect this sensor from the control box and use the same method to check
other sensors. Then insert all sensors into matching ports.
1. The engine must be off during the installation
2. Performance may be affected in heavy rain, gravel roads, bumpy roads, hot or
moist weather, or if the sensor is covered by ice or mud.
3. Other ultrasonic or electric waves (eg voltage reducers) may affect the
performance of the system.
4. The sensors should be installed securely but not over-tight.
5. Its performance may be affected if the sensors are installed in a metal bumper.
6. Avoid installing the digital control box in areas of interference or moisture.
7. Test the system to make sure it works correctly.
8. This system is a reversing aid and the manufacturer accepts no responsibility
for any accident after the kit is installed.
PARKING SENSOR SYSTEM
This system consists of ultrasonic sensors, a control unit and buzzer. This system
detects the distance between the vehicle and obstructions by ultrasonic sensors
installed at the rear of the vehicle.
To avoid ‘Metal Resonance’ use rubber sensors in metal bumpers (APS400R)
or surface mount sensors (APS400W).

8
WARRANTY
Congratulations on your purchase of a quality Reversing System! You’re joining
thousands of satisfied customers who enjoy & experience the benefits of the products we
distribute. In the unlikely event that some technical difficulty arises with your purchase, be
assured that we are most anxious to see that the problem is quickly rectified to your
satisfaction. Please familiarise yourself with the following simple conditions of our warranty.
This warranty covers faults through component failure or failure of the product to operate in
accordance with published specifications. Product failure as a result of unreasonable
environmental conditions, accident, misuse, improper installation, unauthorised repair, vehicle
electrical or wiring faults or neglect etc, will not be covered by this warranty. Removal and
installation costs, if any, would be paid by the owner as well as any freight or postage costs of
transporting the product to AudioXtra. AudioXtra shall not be liable or responsible for any loss
of use of this product or any form of consequential loss.
CONSUMER WARRANTY
This product is warranted by AudioXtra International Pty Ltd to be free from defects in
materials and workmanship under NORMAL USE for a period of TWENTY FOUR MONTHS
from the date of purchase.
WITHIN 30 DAYS OF PURCHASE DATE: Please return the unit for replacement to our
National Service Centre or the Retailer from where you made the purchase. All accessories
must be included. Proof of purchase date
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
must accompany the products.
AFTER 30 DAYS OF PURCHASE DATE: Warranty repair and service is carried out by our
National Service Centre. Repair and service will be carried out at no cost to the owner if proof
of ownership and the date of purchase can be verified to the satisfaction of the authorised
centre concerned with this repair. This proof should take the form of either:
a) The warranty card accompanying this product, stamped and dated by the dealer.
b) A Tax Invoice or Receipt showing full details of original vendor, purchaser, model
number and serial number.
COMMERCIAL WARRANTY: A product used in or associated with a commercial
application will carry a limited SIX MONTH warranty. An abnormal commercial application is
one where usage, dust, vibration, heat/cold and other environmental conditions exist at an
extreme level.
Model Number: Serial Number:
Dealer Name: Date of Purchase: / /
Dealer Address:
www.audioxtra.com.au
Purchaser’s Name:
Invoice/Sales Docket no:
Purchaser’s Address:
National Service Centre:
10 STODDART ROAD, PROSPECT, SYDNEY NSW 2148 Australia
Telephone: [phone] Fax: [phone]
email: [e-mail]
Please complete details below in the event of warranty service being required.
General Hints: To expedite service and prompt return of the equipment, please:
a) Clearly describe the fault in detail c) Include your return address
b) Safety and security pack the unit for transport d) Provide proof of purchase date as outlined above
APS200B