Böcker Toplift User manual

Operating Instructions
Toplift
Toplift Eco
Translation based on the original German version
Document no.:92023200095 Every operator, before he places the device in ser-
vice, must read the operating manual!

Toplift / Toplift ECO
2 92023200095
© Böcker Maschinenwerke GmbH
Lippestr. 69-73
D-59368 Werne
Tel.: [phone]
Fax: [phone]
E-Mail: [email protected]
Internet: www.boecker-group.com

Toplift / Toplift ECO
3 92023200095
Assignment of these operating Instructions
This assembly and operating instruction…
...
Document no.: 92023200095
Original from: 26.07.2006
Version 05102010
… applies to:
Type: Toplift
Serial number: Ab 42850
Typ: Toplift ECO
Serial number: Ab 286

Toplift / Toplift ECO
4 92023200095
CONTENTS :
1FOREWORD................................................................................................................................... 7
1.1 Advice on use of these operating instructions.................................................................... 7
1.2 Safety and danger advice................................................................................................... 7
2TECHNICAL DETAILS.................................................................................................................... 8
2.1 Special characteristics.......................................................................................................... 9
2.2 Composition of the hoist........................................................................................................9
2.3 Accessories ....................................................................................................................... 10
2.3.1 Carriages and ladder accessories.......................................................................... 10
2.3.2 Hoisting devices................................................................................................... 10
3FUNDAMENTAL SAFETY INSTRUCTIONS................................................................................ 11
3.1 Basic operation and designated use of the machine. ...................................................... 11
3.2 Organizational measures.................................................................................................... 11
3.3 Selection and qualification of personnel – Basic responsibilities............................................ 11
3.4 Safety instructions governing specific operational phases ........................................... 11
3.4.1 Standard operation............................................................................................... 11
3.4.2 Special work in conjunction with utilization of the TOPLIFT...................................... 11
3.4.3 Warning of special dangers: Electric energy............................................................. 11
4ASSEMBLY OF THE HOIST......................................................................................................... 12
4.1 Indications for safety......................................................................................................... 12
4.2 Estimation of the rail length ................................................................................................. 12
4.3 Assembly of the rails...........................................................................................................12
4.4 Setting up the rail section.................................................................................................... 12
4.5 Load indicator................................................................................................................... 13
4.6 Mounting of bend section.................................................................................................... 13
4.7 Support of the rail section.................................................................................................... 13
4.8 Assembly of the tube support.............................................................................................. 14
4.9 Head support ..................................................................................................................... 14
4.10 Stability of the hoist............................................................................................................. 14
4.11 The undercarriage.............................................................................................................. 14
4.11.1 Assemly of the undercarriage................................................................................ 14
4.11.2 Moving the TOPLIFT ............................................................................................ 14
4.12 Securing the feet /undercarriage ......................................................................................... 14
4.13 Setting up the drive unit ...................................................................................................... 15
4.14 Assembly and adjustment of the upper limit switch (without MV)........................................... 15
4.15 Assembly and adjustment of the upper limit switch TOPLIFT Furniture (MV)......................... 15
4.16 Electric supply.................................................................................................................... 16
4.17 Fixing the hoisting rope....................................................................................................... 17
4.17.1 Attaching the rope to the standard carriage + furniture carriage............................... 17
4.17.2 Attaching the rope to the tilting carriage.................................................................. 17

Toplift / Toplift ECO
5 92023200095
4.18 Test run..............................................................................................................................17
5APPLICATION OF THE HOISTING DEVICES..................................................................................18
5.1 Standard universal platform..............................................................................................18
5.2 Uni-platform comfort............................................................................................................18
The Uni-platform standard can be used with the standard carriage as well as with the tilting
carriage. .........................................................................................................................................18
5.3 Long-goods-platform...........................................................................................................18
5.4 Platform..............................................................................................................................19
5.5 Sheet platform.....................................................................................................................19
5.6 Tilting bucket.......................................................................................................................19
5.7 Solar-Platform Standard....................................................................................................20
5.8 Solar-Platform adjustable..................................................................................................20
5.9 Sheet transport bed with adjustable inclination.................................................................20
5.9.1 Handling of the Sheet transport bed with adjustable inclination...........................21
5.10 Furniture platform Universal / Basic..................................................................................24
5.10.1 Furniture platform extendable.............................................................................24
5.10.2 Furniture platform pivotable and extendable......................................................24
5.10.3 Furniture platform pivotable and extendable (without front-flap)).......................24
5.10.4 Handling of the furniture platform with pluggable side guards ...........................25
6OPERATION OF THE TOPLIFT ......................................................................................................26
6.1 Before each use..................................................................................................................26
6.2 Control system of the TOPLIFT 225/234/240/M1/M2 ............................................................26
6.3 Control system of the TOPLIFT ECO...................................................................................26
6.4 Control system of the TOPLIFT Furniture (MV).....................................................................27
6.5 Securing the loading area....................................................................................................27
7DISMANTLING THE TOPLIFT.........................................................................................................27
8WARRANTY....................................................................................................................................28
9MAINTENANCE..............................................................................................................................28
9.1 Maintenance intervals..........................................................................................................28
9.2 Changing the rope...............................................................................................................29
9.3 Checking the rope and discarding........................................................................................29
9.4 Fitting of the hoisting rope on the cable drum Toplift 225 Universal / 234 / 240 / Furniture.......29
9.5 Placing of the hoisting cable (5mm) on the Toplift ECO cable winch......................................30
9.6 Fixing the rope to the rope socket.....................................................................................30
9.7 Adjusting the slack rope device............................................................................................30
9.8 Checking the broken rope device......................................................................................30
10 TROUBLE-SHOOTING..................................................................................................................31
11 MASTER DATA..............................................................................................................................32
12 INFORMATION ABOUT THE EXPERT INSPECTION..................................................................34
13 TEST PROTOCOLS ON EXPERT INSPECTION .........................................................................36
14 WIRING DIAGRAMS......................................................................................................................40

Toplift / Toplift ECO
6 92023200095
14.1 Wiring diagram Toplift 225 – 110V................................................................................... 40
14.2 Wiring diagram Toplift 225 Universal, Toplift 234, Toplift Furniture M1........................... 43
14.3 Wiring diagram Toplift 240, Toplift Furniture M2.............................................................. 44
14.4 Wiring diagram Toplift Furniture MV................................................................................. 45
14.5 Wiring diagram Toplift ECO.............................................................................................. 49

Toplift / Toplift ECO
7 92023200095
1 Foreword
Dear customer,
with these operating instructions we want to inform you about the safety,
the usage and the technical details of the TOPLIFT. The following in-
structions and advice are to be strictly adhered to. The operating instruc-
tions will help to avoid danger, repair costs, to reduce downtime and to
increase the reliability and lifetime of the TOPLIFT.
In addition to the operating instructions and to the mandatory rules and
regulations for accident prevention and the environmental protection in
the country and place of use, the generally recognized technical rules for
safe and proper working must also be observed.
For further questions please contact your importer or the manufacturer:
Manufacturer:
Böcker Maschinenwerke GmbH
Lippestr. 69-73
D-59368 Werne
Tel.: [phone]
Fax: [phone]
E-Mail: [email protected]
Internet: www.boecker-group.com
Marking: CE marking
Land of origin Germany
IT IS OF MAJOR IMPORTANCE TO READ THESE OPERATING
INSTRUCTIONS BEFORE USAGE: DURING OPERATION IS TOO
LATE!!
1.1 Advice on use of these operating instructions
The pages are numbered consecutively. The illustrations are numbered
consecutively by chapters.
Example: picture 3-1 means: Illustration (picture) 1 in chapter 3
1.2 Safety and danger advice
The following symbols and names are used to give advice and to warn of
danger.
WARNING: Serious harm or even death can result if this ad-
vice and instruction is not followed.
ATTENTION! Machine damage or damage to property can be
the result if this advice and instruction is not fol-
lowed.
HINT
Following these hints will make work and operation easier.

Toplift / Toplift ECO
8 92023200095
2 TECHNICAL DETAILS
(CONSTRUCTION)
TOPLIFT
225 Universal TOPLIFT 225 – 110 V TOPLIFT 234 TOPLIFT 240 TOPLIFT Eco
Hoisting speed: 25 (30) m/min 25 (30) m/min 34 m/min 20/40 m/min 25 m/min
Capacity: 250 kg 200 kg 250 kg 230 kg 150 kg
Standard height: 11,30 m 11,30 m 11,30 m 11,30 m 11,30 m
Max. eaves height: 20,50 m 20,50 m 20,50 m 20,50 m 20,50 m
Weight drive unit: 54 kg 54 kg 54 kg 54 kg 47 kg
Rope diameter: 6 mm 6 mm 6 mm 6 mm 5 mm
Standard rope length: 44 m 44 m 44 m 44 m 44 m
230 V / 50 Hz 110 V / 50 Hz 230 V / 50 Hz 230 V / 50 Hz 220 V / 50 HzMotor voltage: 110 V / 60 Hz 110 V / 50 Hz
Control voltage: 24 V 24 V 24 V 24 V 24 V
Motor power: 1,3 kW 1,3 kW 1,3 kW 0,6/1,2 kW 1,6 kW
Max. operating time 40 % ED 40 % ED 40 % ED 40 % ED 40 % ED
Supply line 3 x 2,5 mm² 3 x AWG10“
(3 x 5.26mm²) 3 x 2,5 mm² 3 x 2,5 mm² 3 x 2,5 mm2
Length supply line max. 40 m max. 40 m max. 40 m max. 40 m max. 40 m
Fuse 16 A träge 32 A träge 16 A träge 16 A träge 16 A träge
sound pressure level
Lpa <70dB <70dB <70dB <70dB <70dB
(FURNITURE)
TOPLIFT
Furniture
(MV)
TOPLIFT
Furniture
(M1)
TOPLIFT
Furniture
(M2)
Hoisting speed: 36 m/min 34 m/min 20/40 m/min
Capacity: 200 kg 200 kg 200 kg
Standard height: 11,30 m 11,30 m 11,30 m
Max. eaves height: 20,50 m 20,50 m 20,50 m
Weight drive unit: 57 kg 54 kg 54 kg
Rope diameter: 6 mm 6 mm 6 mm
Standard rope length: 44 m 44 m 44 m
Motor voltage: 220 V / 50 Hz 230 V / 50 Hz 230 V / 50 Hz
Control voltage: 24 V 24 V 24 V
Motor power: 2,2 kW 1,3 kW 0,6/1,2 kW
Max. operating time 40 % ED 40 % ED 40 % ED
Supply line 3 x 2,5 mm23 x 2,5 mm² 3 x 2,5 mm²
Length supply line max. 40 m max. 40 m max. 40 m
Fuse 16 A time lag 16 A time lag 16 A time lag
sound pressure level
Lpa <70dB <70dB <70dB

Toplift / Toplift ECO
9 92023200095
Fig. 2-1
2.1 Special characteristics
The TOPLIFT is an easily assembled aluminium
ladder hoist for construction work under the terms of
EN 12158-2.
2.2 Composition of the hoist
Find the composition of the hoist in the current
price list.
.

Toplift / Toplift ECO
10 92023200095
2.3 Accessories
Standard carriage
picture 2-2
Tilting carriage
picture 2-3
Furniture carriage universal
picture 2-4
2.3.1 Carriages and ladder accessories
Part No.
0220135000 Standard carriage 22 kg
0226832000 Tilting carriage 59 kg
2023200056 Furniture carriage universal 26 kg
0220113000 Head support 7 kg
0225300000 Aluminium double support 19 kg
0225000000 Bend section 19,5 kg
2023200031 Undercarriage 26 kg
0221605000 Extension 2 meter 12 kg
0221603000 Extension 1 meter 6 kg
0000550012 Cable drum 3x2,5 mm² 13 kg
5020700000 Tile roller 10 kg
2.3.2 Hoisting devices
Part No.
0226700000 Tilting bucket 80 ltr. 29 kg
0224200000 Uni- platform standard 28 kg
2023200020 Uni – platform comfort 32 kg
0224300000 Sheet platform 22 kg
394010020 Sheet transport bed with ad-
justable inclination 40 kg
2023200021 Long-goods-platform 38 kg
0224900000 Platform 26 kg
2023200036 Solar-platform standard 31 kg
2023200037 Solar-platform adjustable 25 kg
2023400001 furniture platform universal
(pivotable and extendable) 84 kg
2023400012 furniture platform universal
(extendable)
2023400013 furniture platform universal
(pivotable and extendable,
without front-flap)
WARNING! The furniture
carriage universal 2023200056 is not ap-
propriate for operation with knee joint!
The hoisting devices will be explained in
chapter 5!

Toplift / Toplift ECO
11 92023200095
3 FUNDAMENTAL SAFETY
INSTRUCTIONS
3.1 Basic operation and designated
use of the machine.
The TOPLIFT has been built in accordance with
state-of-the-art standards and recognized safety
rules. Nevertheless, its use may constitute a risk to
life and limb of the user or third parties, or cause
damage to the lift and to other material property.
The lift must only be used in good working condition
in accordance with its designated use and the in-
structions set out in the operating manual, and only
by safety-conscious persons who are fully aware of
the risks involved in operating the TOPLIFT. Any
functional disorders, especially those affecting the
safety of the lift, should be rectified immediately.
The TOPLIFT is an easily assembled construc-
tion hoist designed only for the transportation of
products under the terms of the operational
safety order in accordance with BGV D7
Transportation of personnel is strictly forbidden
Using the TOPLIFT for purposes other than those
mentioned above (such as transportation of person-
nel) is considered contrary to its designated use. The
manufacturer cannot be held liable for any damage
resulting from such use. The risk of such misuse lies
entirely with the user.
3.2 Organizational measures
The operating instructions must always be at hand at
the place of use of the lift. Anyone who will have to
work with the TOPLIFT has to read the operating in-
structions before starting to work.
3.3 Selection and qualification of per-
sonnel – Basic responsibilities
Any work on and with the TOPLIFT must be exe-
cuted by reliable personnel only. Statutory minimum
age limits must be observed.
Make sure that only authorized personnel works on
or with the TOPLIFT.
3.4 Safety instructions governing
specific operational phases
3.4.1 Standard operation
Avoid any operational mode that might be prejudicial
to safety.
Before beginning to work, familiarize yourself with
the surroundings and circumstances of the site, such
as obstacles in the working and travelling area, the
soil bearing capacity and any barriers separating
the construction site from public roads. Take the
necessary precautions to ensure that the machine is
used only when in safe and reliable state, so that no
one can be exposed to danger.
3.4.2 Special work in conjunction with
utilization of the TOPLIFT
Spare parts have to conform to the technical re-
quirements stated by the manufacturer. This is al-
ways guaranteed by original spare parts.
Observe the adjusting, maintenance and inspection
activities and intervals set out in the operating in-
structions, including information on the replacement
of parts and equipment. These activities may be
executed by skilled personnel only. Annual audit by
the operational safety order in accordance with BGV
D7
Always tighten any screwed connections that have
been loosened during maintenance and
repair.
Any safety devices removed for set-up, maintenance
or repair purposes must be refitted and checked im-
mediately upon completion of the maintenance and
repair work.
Ensure that all consumables and replaced parts are
disposed of safely and with minimum environmental
impact.
3.4.3 Warning of special dangers: Elec-
tric energy
Use only original fuses with the specified current rat-
ing. Switch off the TOPLIFT immediately if trouble
occurs in the electrical system.
Work on the electrical system or equipment may only
be carried out by a skilled electrician or by specially
instructed personnel under the control and supervi-
sion of such electrician and in accordance with the
applicable electrical engineering rules.
Before opening the control box, draw in any
case the mains plug.

Toplift / Toplift ECO
12 92023200095
4 ASSEMBLY OF THE HOIST
4.1 Indications for safety
Make yourself familiar with the surroundings before
assembling the TOPLIFT. Pay attention to the soil
bearing and separate the construction site from pub-
lic access. The working area of the TOPLIFT has to
be separated by a fence. This fence has to consist of
at least two horizontal elements which have to be
marked with contrasting colours (for exp. red/white).
picture 4-1 (All dimensions in meters)
4.2 Estimation of the rail length
Take vertical lifting height and add approximately
20% for inclination. Increase to full meter.
4.3 Assembly of the rails
1. Place foot section on the ground and fit feet or
undercarriage.
2. Introduce carriage with rollers onto the rail.
picture 4-2
Hint! The knurled cams of the broken rope device
located on the upper axle have to be released
by raising the linkage.
3. Slide the carriage to the bottom of the foot sec-
tion.
4. Place the extensions of 2 or 1 m on the ground.
5. Join the extensions.
Attention! The ring nuts are on the outside
of the rails!!!
picture 4-3
6. Place the head section on the rails and tighten as
well.
7. Tighten all ring nuts.
4.4 Setting up the rail section
Up to 8 m length, the rail can be set up by hand and
brought in the right inclination as a ladder.
Anchor the feet with pins.
Up to 13 m length, the rail can be raised from above
by a rope.
Hint! The rope has to be at-
tached in the middle of the
head section or upper end of the rail to
avoid that the hoist will not tilt sideways.
Push along the rail section until the right inclination
has been reached.
Above 13 m length, assemble the rail on the ground
and raise as above until vertical.
1. Raise the rails about 2.30 m.
2. Add further sections to the bottom of the rail.
3. Finally add the foot section with carriage fitted.
4. Incline to correct angle, then fit adjustable sup-
port.

Toplift / Toplift ECO
13 92023200095
4.5 Load indicator
The capacity of the hoist depends on length and angle of inclination of the rail. Refer to the load indicator on the
foot section (picture 4-4).
picture 4-4
The load indicator is placed on the left side of the foot section. The indicator shows, to which height the rails
can be loaded in the current inclination. The maximum load is 250 kg.
Hint! See to it that the load indicator can always move freely so that the exact inclination can be
seen.
Attention! If, by assembling, the extensions with the old profile form (type TOPLIFT Standard, B or
C) and extensions with the new profile form (Type TOPLIFT standard 150, 200 or 200 HS) are com-
bined, then the total maximum capacity is 150 kg.
4.6 Mounting of bend section
1. Set up the rail with carriage fitted.
2. Place the bend section and tighten the screws.
3. Add further extensions (min. 1 meter).
4. Add the head section and attach it to the exten-
sions.
5. Adjust the bend section according to the inclina-
tion of the roof and tighten screws firmly.
picture 4-5
4.7 Support of the rail section
The rail should be supported by the adjustable tube
support if the rail is longer than 8 m or inclined more
than 75°.
Attention! When transporting long goods
the rail has always to be reinforced by the
tube support. It is important that the maxi-
mum unsupported length does not exceed 8 m. If the
rail length exceeds 13.30 m (without rail being sup-
ported by roof), use an additional tube support or the
Alu-support for window openings.

Toplift / Toplift ECO
14 92023200095
4.8 Assembly of the tube support
picture 4-6
The tube support is to be fixed to a rung and to be
extended to a suitable length and the lower section is
to be placed on a plank or similar on the ground.
4.9 Head support
picture 4-7
When the hoist is used on flat roofs, floors or win-
dows, the rail should be protected against lateral
movement, by using the head support. This can be
fitted directly beneath the head section or between
two rungs.
4.10 Stability of the hoist
The rail must be secured on the upper point (head
section) by attaching the ring nuts with a cable or
rope to the building.
When using the bend section, this must also be at-
tached to the building with a cable or rope.
4.11 The undercarriage
If the hoist is equiped with an undercarriage, it can
be moved sideways along the building.
4.11.1 Assemly of the undercarriage
The undercarriage has to be fixed before setting up
the rail section.
1. Dismantle the feet, these are fixed with a bolt
and a split-pin.
2. Add the undercarriage and secure by bolt and
split-pin (picture 4-8)
picture 4-8
4.11.2 Moving the TOPLIFT
Attention! Before moving
the hoist, make sure that
the carriage is in the low-
est position. Detach the rope or cable from
the head section. Never move the hoist
when loaded.
1. Ride the carriage down.
2. Unload the hoisting device.
3. Release the brakes of the undercarriage.
4. Move the hoist.
5. Set the brakes again. ( Turn the brake shoes at
the wheels to the outside)
4.12 Securing the feet /undercarriage
Place the hoist with its feet on solid ground and se-
cure by pins. (If necessary place plank below for dis-
tribution of pressure). When using the undercarriage
adjust spindles so that both wheels are firmly on the
ground. Put on brake shoes.

Toplift / Toplift ECO
15 92023200095
4.13 Setting up the drive unit
The drive unit is to be put onto the lower rung of the
foot section. Make sure that the drive unit is placed in
the middle of the ladder rung (picture 4-9)
Neues Bild
picture 4-9
1. Put the drive unit into the rail and unlock it by pull-
ing up the handle.
2. At lock-in device in position “unlocked” put the
drive unit with energy into the next rung.
3. Check that the locker hooks on the rung.
4. Put the 5-pole plug of the hand control in the
middle socket on the drive unit.
5. Put the 3-pole plug of the limit switch cable in the
upper socket on the drive unit.
4.14 Assembly and adjustment of the
upper limit switch (without MV)
picture 4-10
1. Screw the limit switch holder on to the head
section.
2. Take limit switch cable up to the head section
and fix it to the holder with the wing-screw.
3. Lead the limit switch cable down the rails and
fix it to the eye screws of the rails.
4. Wind the remaining cable carefully and fix it to
the side of the drive unit.
4.15 Assembly and adjustment of the
upper limit switch TOPLIFT Furni-
ture (MV)
picture. 4-11
1. Screw the limit switch holder with the limit
switch already mounted and the limit switch
cable (2) to the first rail underneath the head
piece.
2. In doing so, please observe the measure-
ments given in Fig. 4-11.
3. Now fasten the limit switch holder to the rear
side of the rail using the knurled screw, so
that it can no longer be moved.
4. The position of the limit switch roll must be
adapted to the respective furniture car-
riage.(Fig. 4-12)
5. Direct the connecting cable (1) behind the
head piece and guide it downwards.
6. Wind the remaining cable carefully and fix it to the
side of the drive unit.

Toplift / Toplift ECO
16 92023200095
picture 4-12
4.16 Electric supply
Warning! Electrical shock,
burning and injuries can result
from:
•Touching
•Damaged insulation
•Unsufficient maintenance
•Short circuit
The electrical connection has to be executed by a
skilled electrician and in accordance with the appli-
cable engineering rules. Electric supply must be
made by a distribution unit with an earth leakage
breaker.
Secure with a 16A time lag
Hint! The cable has be totally un-
wound. The use of the proper supply
cable is essential as otherwise there may be a loss
of voltage resulting in damage in the controls.
Type Toplift 225 / 234 / 240 / Eco/
Furniture (MV,M1,M2) :
Cross section of the cable: 3 x 2.5 mm²
Maximum length supply line: 40 m
Type Toplift 225 / 110 Volt/50 Hz:
Cross section of the cable: 3 x AWG10”
(3x5.26 mm²)
Maximum length supply line: 40 m
Furniture carriage
limit switch
roll

Toplift / Toplift ECO
17 92023200095
4.17 Fixing the hoisting rope
Attention! Wear gloves to avoid injuries while fix-
ing the hoisting rope.
1. Take the end of the hoisting rope in one hand
and operate the hand control with the other
one. Push the button "DOWN".
See to it that the rope remains raught during
unwinding, to avoid that the slack rope device
stops the motor.
2. Take the rope up the righthand side to the head
section.
picture 4-13
3. Put the rope from the right to the left over the
rope pulley. ( see picture 4-13) .
Make sure that the cable is seated correctly
in the trail of the cable deflection pulley.
4. Lead the rope down at the lefthand side.
4.17.1 Attaching the rope to the stan-
dard carriage + furniture car-
riage
The rope locker at the end of the rope is to be at-
tached to the rope connection on the standard car-
riage (pins). At this point the broken rope device is
still on, push the button UP on the hand control to
tighten the rope.
4.17.2 Attaching the rope to the tilting
carriage
1. Open the lids of the rope pulleys.
2. Lead the rope from the left to the right on the
lower pulley at the rear. (The rope lies behind
the bar of the broken rope device)
3. Now lead the rope from the right to the left over
the pulley roller and switch back the lid. ( The
rope lies now in front of the bar of the broken
rope device)
4. Lead the rope from the left to the right over the
the upper pulley in the front and close the lid.
(The rope lays in front of the bar of the broken
rope device)
5. Attach the rope locker to the carriage.
6. Check the moving direction of the rope. Seen
from above the rope goes two times behind the
bar of the broken rope device and three times in
front of it.
4.18 Test run
Before the initial operation of the TOPLIFT check
whether:
•All safety devices are in working order,
•The limit switches at the top and at the bottom
are in order,
•The broken rope device on the carriage is in or-
der,
•The loading area is secured,
•When using the bend section, the bend section
and the extensions are properly supported on
the roof,
•The inclination of an extension on the roof is at
least 25°,
•The hoist is supported,
•The voltage is sufficient, when the TOPLIFT is
operated carrying the rated load.

Toplift / Toplift ECO
18 92023200095
picture 5-1
picture 5-2
picture 5-3
5 Application of the hoisting de-
vices Warning! The transportation of per-
sonnel and entering the platform is for-
bidden.
For the intended use of the Toplift the only hoisting
devices allowed to be used are those described
here.
All hoisting devices are fixed to the carriage by 4
pins. The upper pins are secured by spring lockers
5.1 Standard universal platform
The dimensions of the platform are 60x35x85 cm.
The standard universal platform can be used with
the standard carriage as well as with the tilting car-
riage. For loading the universal platform the side
gratings can be lifted up and swung to the side at the
same time. The standard universal platform has a
load-bearing capacity of max. 250 kg, reduction
depending on type.
5.2 Uni-platform comfort
The Uni-platform comfort has a load-bearing ca-
pacity of max. 250 kg, reduction depending on
type. The dimensions of the uni – platform com-
fort are 70 x 44 x 70 cm.
The Uni-platform standard can be used with the
standard carriage as well as with the tilting car-
riage.
5.3 Long-goods-platform
The Long-goods-platform can be used in conjunction
with both carriages. The dimensions of the Longs-
good platform are 120x35x45 cm. For loading, the
gratings can be opened.

Toplift / Toplift ECO
19 92023200095
picture 5-4
picture 5-5
picture 5-6
5.4 Platform
The Platform is only to be used with the standard
carriage. The Platform is height-adjustable and is
equiped with tiltable side-boards. Dimensions are
60x85 cm.
max. capacity: 200 kg
5.5 Sheet platform
The Sheet platform serves for the transportation of
large plates (plasterboards) and windows. The di-
mensions are 90x15x220 cm. To use this Sheet plat-
form in conjunction with the tilting carriage, the sup-
plied switch cam has to be bolted to the platform.
The advantage of using the tilting carriage is that the
Sheet platform, can be tilted to the horizontal posi-
tion, when arrived at the top, so that unloading of
boards is easier. The maximum width of the products
is 150 cm. The material has to be secured by the
chain.
max. capacity: 200 kg
5.6 Tilting bucket
The Tilting bucket is only to be used with the tilting
carriage. The maximum contents is 80 Ltr. The
bucket can be manually tipped at the bottom, to off
load the material or debris.
1. Release the catch lever at the right side of the
bucket.
2. Tilt the bucket forwards using the handle.
3. Latch the bucket back into the catch lever.
max. capacity: 250 kg

Toplift / Toplift ECO
20 92023200095
picture 5-7
picture 5-8
picture 5-9
5.7 Solar-Platform Standard
The solar-platform-standard may be used in
combination with standard or tilting carriage.
This platform is particularly designed for the
transport of smaller solar and photovoltaic instal-
lations.
The modules are fixed by means of a continu-
ously variable clamping device with rubber vibra-
tion pad.
max. capacity: 200 kg
5.8 Solar-Platform adjustable
The adjustable solar platform can be used with
standard or tilting carriage. It is mainly used for
the handling of larger solar elements. The base
frame is rubber cushioned. The lateral bars can
be extended to 1.55 m.
max. capacity: 200 kg
5.9 Sheet transport bed with adjust-
able inclination
The sheet transport bed with adjustable inclina-
tion serves to convey large sheets and panels
(gypsum board panels, windows, etc.). The parts
to be conveyed may have a maximum width of
150 cm, a maximum height of 210 cm and a
maximum depth of 15 cm. The platform bed can
be used with a carriage or a tilting carriage. With
the tilting carriage combination it must be en-
sured that the tilting function is not activated.
The use of the sheet transport bed with adjust-
able inclination is advantageous, as the con-
veyed material can be horizontally unloaded at
the loading point and then fits through window
openings due to the second tilting option.
The material is secured by chains.
max. capacity: 150 kg