B-K lighting Denali Series User manual

RELEASED
11-04-2019
REFERENCE NUMBER
INS-2809-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
5/32”, 3/16”, 0.050” & 5/64” Allen Wrench
Waterproof Wire Connectors
Phillips Screwdriver
Inspiration Control System on iOS Device
NEEDED
FOR
INSTALLATION:
By Others
This set of instructions
works for:
Denali Series™
Stainless Steel Tree Strap
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
· Suitable for wet locations ·
IMPORTANT LISTINGS AND CERTIFICATIONS
Warning High Voltage
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.
• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.
• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time. Use
a soft cloth or gloves. Oil from skin may cause damage.
SAVE THESE INSTRUCTIONS
PTR-DE-TR-C
Denali Series™
For integral fixture
configurations
360HD™ Knuckle
Tree Stand-Off
Splice Box
Secondary Cable Quick
Disconnect
PALM TREE RING INTEGRAL
Denali Series™
Standard Installation
iOS device with installed Inspiration Control System
App is required for Bluetooth® Wireless Control.
Bluetooth® version 4.0 or higher required.
iOS Devices:
iPhone - iPhone 4s or newer
iPad - 3rd Gen iPad or newer
iPad Mini
iPad Air
iPod - iPod Touch 5th Gen or newer
Device Requirements

RELEASED
11-04-2019
REFERENCE NUMBER
INS-2809-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
Fixture Installation
1. Place tree ring fixture around tree.
Move fixture to desired height. Tighten
the entire assembly to the tree with
provided stand-offs.
2. Secure by hooking end of strap over two (2)
Phillips screws. Secure by tightening two (2)
Phillips screws with Phillips screwdriver.
5. Bring line voltage cable from power line to
main splice box location. Loosen cord grip on
bottom of splice box, feed line voltage cable
from power line through, then tighten cord
grip to secure.
4. Remove top of driver housing by removing (4)
#8-32 set screws using 5/64” Allen wrench.
Driver housing will be marked for primary.
PALM TREE RING INTEGRAL
Denali Series™
Standard Installation
3. Connect secondary cable then twist to secure
in place.
iOS device (Not Included) with installed B-K Lighting Inspiration Application required for use.
WIRING DIAGRAM - DMX Controls with
Inspiration Application on iOS device
LINE
MODULE
COM
HydroLock®
Plate
Red
Black
iOS
Bluetooth®
LCT
iOS
Bluetooth®
GROUND
Brown (LINE)
MODULE
Blue (COM)
Driver
Red (+)
Black (-)
iOS
Bluetooth®
Green (GROUND)
GROUND IN HOUSING
LINE
COM
Driver
Driver
iOS
Bluetooth®
MODULE
MODULE
Red
Black
Red
Black
LINE
MODULE
COM
Remote
Driver
Red
Black
GROUND
HydroLock®
Plate
LINE
COM
GROUND
MODULE
Driver
10V
0V Gray (0-10V DIM -)
Violet (0-10V DIM +)
Orange (0-10V CCT +)
White (0-10V CCT -)
Dimming
Continuous
CCT
10V
0V
iOS
Bluetooth®
MODULE
Driver
10V
0V
Dimming
Continuous
CCT
10V
0V
Brown (LINE)
Blue (COM)
Green (GROUND)
Red (+)
Black (-)
Gray (0-10V DIM -)
Violet (0-10V DIM +)
Orange (0-10V CCT +)
White (0-10V CCT -)
Brown (LINE)
Blue (COM)
Green (GROUND)
Red (+)
Black (-)
LINE (BROWN)
COM (BLUE)
ASV™ Wire
Connector
iOS
Bluetooth®
GROUND (GREEN)
LINE (BROWN)
COM (BLUE)
ASV™ Wire
Connector
iOS
Bluetooth®
GROUND (GREEN)
0-10V CCT + (ORANGE)
0-10V CCT - (WHITE)
0-10V DIM + (VIOLET)
0-10V DIM - (GRAY)
LINE (BROWN)
COM (BLUE)
ASV™ Wire
Connector
GROUND (GREEN)
0-10V CCT + (ORANGE)
0-10V CCT - (WHITE)
0-10V DIM + (VIOLET)
0-10V DIM - (GRAY)
LINE
MODULE
COM
GROUND
Driver
Red
Black
DMX
MODULE
LINE
MODULE
COM
GROUND
Driver
Red
Black
DMX
120Ω
LINE
MODULE
COM
GROUND
Driver
DMX GROUND
DMX DATA +
Red
Black
DMX DMX DATA -
LINE
MODULE
COM
GROUND
Driver
DMX GROUND
DMX DATA +(WHITE W/ ORANGE)
Red
Black
DMX
DMX DATA - (ORANGE)
DMX GROUND
DMX DATA +(WHITE W/ ORANGE)
DMX DATA - (ORANGE)
DMX GROUND
DMX DATA +(WHITE W/ ORANGE)
DMX DATA - (ORANGE)
iOS
Bluetooth®
iOS device must be within 5ft of fixture for
wireless operation.
iOS device controls dimming, CCT, Saturation,
and Hue using Bluetooth® wireless controls and
the application. DMX Controls (By Others) are
handled by external DMX programming.
iOS device (iPad, iPod, iPhone) with installed
B-K Lighting Inspiration application is
required.
6. Replace top of driver housing with (4) #8-32
screws with 5/64” Allen wrench.
7. Run DMX cable through hook on steel tree
strap and bring down alongside line voltage
cable.

RELEASED
11-04-2019
REFERENCE NUMBER
INS-2809-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
360HD™ Knuckle
Standard Installation
PALM TREE RING INTEGRAL
Denali Series™
4. Tighten (1) 3/8”-16 x 3/8” stainless steel black
oxide set screw on the stem to secure horizontal
aiming position.
Tighten (1) 1/4”-28 x 1-1/4” stainless steel black
oxide socket head cap screw to 24” minimum to
48” maximum pounds to secure vertical aiming
position
2. Rotate fixture at base and aim fixture to desired
horizontal location.
1. Use 3/16” Allen wrench to slightly loosen
(1) 3/8”-16 x 3/8” stainless steel black oxide set
screw on the stem for 360° aiming purpose.
Warning: Do not over tighten set screw.
Doing so will compromise O-ring seal and will
void warranty.
3. Use 3/16” Allen wrench to loosen (1) 1/4”-28 x
1-1/4” stainless steel black oxide socket head
cap screw at the knuckle for vertical aiming
purpose.

Standard Installation
PALM TREE RING INTEGRAL
Denali Series™
iOS device (Not Included) with installed B-K Lighting Inspiration Application required for use.
11. Place cap on fixture and tighten three (3)
#8-32 set screws with 5/64” Allen wrench.
Top of screws should sit flush with fixture cap.
Warning: Do not over tighten set screw.
Doing so will compromise O-Ring seal and
will void warranty.
To Replace Module
1. Remove cap by loosening three (3) #8-32 set
screws using a 5/64” Allen wrench.
3. Loosen, then remove three (3) #2-28 screws
from optic module using .050” Allen wrench.
Remove optic holder from module.
5. Carefully remove LED module from heatsink,
and disconnect the quick disconnect from the
LED module.
Do not pull on connectors or wiring. Handle
with care.
4. Loosen and remove two (2) #4-40 screws
holding LED module to heatsink using 0.050”
Allen wrench.
2. Gently twist optic to the left so optic tabs are clear
of optic holder and carefully pull away.
8. Secure LED module to heatsink with two (2)
#4-40 screws.
7. Connect new LED module via quick
disconnects. Place new LED module onto
heatsink, lining up module with holes for
screws.
10. Line up optic tabs in the optic holder, then gently
twist to the right to secure.
9. Tighten three (3) #2-28 screws on optic module
using .050” Allen wrench to secure optic holder.
6. Spread new thermal paste in even layer on
heatsink. Line up new LED board and place on
heatsink.
RELEASED
11-04-2019
REFERENCE NUMBER
INS-2809-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.