B-K lighting NITE STAR SERIES User manual

NITE STAR SERIES™
Bluetooth® Wireless Technology
RELEASED
4-8-16
REFERENCE NUMBER
INS-2407-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
TOOLS
NEEDED:
By Others
Optional 360SL™
Knuckle Mounting
System
Locknut
Warning Low Voltage Hot Surface
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
1/2” NPS Threaded Hub
Please refer to the low voltage design guide at www.bklighting.com/lvguide before installation for proper wire selection.
3/16” & 5/32” Allen Wrench
Waterproof Wire Connectors
Inspiration Control System on iOS Device
iOS device with installed Inspiration Control System
App is required for Bluetooth® Wireless Control.
Bluetooth® version 4.0 or higher required.
iOS Devices:
iPhone -iPhone 4s or newer
iPad -3rd Gen iPad or newer
iPad Mini
iPad Air
iPod -iPod Touch 5th Gen or newer
Device Requirements
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.
• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.
• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time. Use
a soft cloth or gloves. Oil from skin may cause damage.
SAVE THESE INSTRUCTIONS

1. Mount fixture onto suitable enclosure according
to designed lighting plan.
2. Secure ½” NPS stem to mounting option. Secure
with provided locknut if applicable.
3. Pull remote wiring through mounting plate.
Make connections from remote transformer to
fixture leads using waterproof wire connectors
(By Others). See wiring diagram.
NITE STAR SERIES™
Bluetooth® Wireless Technology
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
RELEASED
4-8-16
REFERENCE NUMBER
INS-2407-00
Wireless Bluetooth® Controls with Inspiration Application
WIRING DIAGRAM - Wireless Bluetooth® Controls
with Inspiration Application on iOS device
0-10V wired hybrid (0-10v wired dimming & continuous cct /sat.and hue by LCT)
LINE
MODULE
COM
GROUND
Remote
Driver
10V
0V Gray (Common)
Violet (0-10V)
Red
Black White (Common)
Blue (0-10V)
Dimming
Continuous
CCT
10V
0V
LINE
MODULE
COM
Remote
Transformer
Red
Black
LCT
wireless (0-10v dimming, continuous cct, sat. and hue by LCT)
LINE
MODULE
COM
GROUND
Remote
Transformer
10V
0V Gray (Common)
Violet (0-10V)
Red
Black
Dimming
hybrid (0-10v dimming wired, /continuous cct, sat. and hue by iOS)
LINE
MODULE
COM
Remote
Transformer
12V
COM
iOS
Bluetooth®
wireless (0-10v dimming, continuous cct, sat. and hue by Ipod/Ipad/Iphone)
LCT
iOS
Bluetooth®
GROUND
GROUND
LINE
MODULE
COM
Remote
Driver
Red
Black
iOS
GROUND
DCA
DMX
Controls
xxxxx
xxxx
PRELIMINARY
LINE
MODULE
COM
GROUND
Remote
Driver
10V
0V Gray (Common)
Violet (0-10V)
Red
Black
LCT
Dimming
hybrid (0-10v dimming wired, /continuous cct, sat. and hue by LCT)
0-10V wired hybrid (0-10v wired dimming & continuous cct /sat.and hue by LCT)
LINE
MODULE
COM
GROUND
Remote
Driver
10V
0V Gray (Common)
Violet (0-10V)
Red
Black White (Common)
Blue (0-10V)
Dimming
Continuous
CCT
10V
0V
0-10V wired hybrid (0-10v wired dimming & continuous cct /sat.and hue by iOS)
LINE
MODULE
COM
GROUND
Driver
10V
0V Gray (Common)
Violet (0-10V)
Red
Black White (Common)
Blue (0-10V)
Dimming
Continuous
CCT
10V
0V
LCT
iOS
Bluetooth®
iOS
Bluetooth®
LINE
MODULE
COM
HydroLock®
Plate
Red
Black
iOS
Bluetooth®
GROUND
LINE
MODULE
COM
Integral
Transformer
12V
COM
iOS
Bluetooth®
wireless (0-10v dimming, continuous cct, sat. and hue by Ipod/Ipad/Iphone)
GROUND
DE WIRING CHECK
DE WIRING CHECK
DE WIRING CHECK
DE WIRING CHECK
DE WIRING CHECK
iOS device must be within signal range of
fixture for wireless operation.
iOS device controls dynamic lumen output using
Bluetooth® wireless controls and the application.
iOS device (iPad, iPod, iPhone) with installed
B-K Lighting Inspiration application is
required.
iOS device (Not Included) with installed B-K Lighting Inspiration Application required for use.
4. Use 5/32” Allen wrench to slightly loosen #10-32
stainless steel black oxide socket head cap screw
at the knuckle for aiming purposes. Tighten to
secure desired location.
LED - For use with 12VAC remote
transformer or magnetic transformers only.
B-K Lighting cannot guarantee performance
with third party manufacturers’ transformers.

RELEASED
1-31-14
REFERENCE NUMBER
INS-2097-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
Warning Hot Surface
TOOLS
NEEDED:
By Others
5/32” & 5/64” Allen wrench
360SL™ Mounting System
Standard Adjustment
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, O-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations · Additionally suitable for mounting within 4 ft. of the ground
IMPORTANT LISTINGS AND CERTIFICATIONS
360SL™ Knuckle
2. Rotate fixture at base and aim fixture to desired
horizontal location.
3. Use 5/32” Allen wrench to loosen #10-32 stainless
steel black oxide socket head cap screw at the
knuckle for vertical aiming purpose.
1. Use 5/64” Allen wrench to slightly loosen two (2)
#8-32 stainless steel set screws on the stem for 360°
aiming purpose.
4. Tighten two (2) #8-32 stainless steel set screws on
stem to secure horizontal aiming position.
Tighten #10-32 stainless steel black oxide socket
head cap screw to 15” minimum to 30” maximum
pounds to secure vertical aiming position.
Warning: Do not over tighten set screw. Doing
so will compromise O-ring seal and will void
warranty.

RELEASED
2-24-16
REFERENCE NUMBER
INS000001
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
TECHNOLOGY
with
TECHNOLOGY
5/64” & 9/64” Allen Wrench
Small Flat Head Screw Driver
Warning Low Voltage Hot Surface
LED BOARD/DRIVER/OPTICS
2 1/4” Body Size
Standard Installation/Replacement
Re-placing LED Board/Driver and Optics
1. Use 5/64” Allen wrench to loosen #8-32 stainless
set screw and remove cap.
2. Space three fingers evenly around the optic and
gently rock optic to remove.
4. Disengage LED board and driver assembly. Replace
with new board and driver assembly. 5. Reverse install LED board and driver by carefully
engaging quick disconnects and inserting into
fixture body. Secure LED board in place with
stainless steel screws. Snap optics in place.
6. With flat head screw driver rotate dial to desired
lumen output. Replace cap by securing #8-32
set screw with 5/64” Allen wrench. Do not over
tighten set screw.
3. Use 5/64” Allen wrench to remove two (2) #2-56
socket head cap screws on LED board, grasp
LED board and gently pull up to expose quick
disconnect.
This product is available with Adjust-e-Lume® (Patent Pend.) for DynamicLLumen Output Control
Warning! The light output of this product may be dynamically adjusted as desired to raise and lower light levels. Please ensure the xture is set to the
appropriate light level desired during installation.
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Followproductlabelinformationandinstructions.
• QualifiedPersonnelmust performallservicing orrelampingof
this product.
• Beforewiringtopowersupplyandduringservicingorrelamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Donotblocklightemanatingfromproductinwholeorpart,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
IMPORTANT LISTINGS AND CERTIFICATIONS
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
TOOLS
NEEDED:
By Others

RELEASED
2-24-16
REFERENCE NUMBER
INS000001
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
TECHNOLOGY
with
TECHNOLOGY
LED BOARD/DRIVER/OPTICS
2 1/4” Body Size
Standard Installation/Replacement
7. Place cap on fixture and tighten set screw. Tighten
screw to 1/2 inch pounds. Top of screw should sit
flush with fixture cap.
Warning: Do not over tighten set screw.
Doing so will compromise O-Ring seal and
will void warranty.
To Change Lumen Output (when required).
1. Use 5/64” Allen wrench to loosen #8-32
stainless set screw and remove cap.
3. Place cap on fixture and tighten set screw.
Tighten screw to 1/2 inch pounds. Top of
screw should sit flush with fixture cap.
Warning: Do not over tighten set screw.
Doing so will compromise O Ring seal and
will void warranty.
2. With flat head screw driver rotate dial to
desired lumen output.
This product is available with Adjust-e-Lume® (Patent Pend.) for DynamicLLumen Output Control
Warning! The light output of this product may be dynamically adjusted as desired to raise and lower light levels. Please ensure the xture is set
to the appropriate light level desired during installation.