B-K lighting NS User manual

RELEASE
7-15-16
REFERENCE NUMBER
INS000929.1
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
5/32” and 5/64” Allen Wrench
Waterproof Wire Connectors
Warning Hot Surface
NEEDED
FOR
INSTALLATION:
By Others
NS™ / NSII™ / DS™ / SH™ FLOODLIGHT
Low Voltage Halogen
Standard Installation
This set of instructions works for:
Locking ‘O’ Ring
Compression
Knuckle
(L.O.C.K.™)
1/2” NPS
Threaded
Nipple
Locknut
(Retaining Ring)
NSII- Nite Star II™
DS - Delta Star™
SH - Shasta Series™
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Followproductlabelinformationandinstructions.
• QualifiedPersonnel mustperform allservicing orrelamping of
this product.
• Beforewiringtopowersupplyandduringservicingorrelamping,
turnoffpoweratfuseorcircuitbreakerbeforeservice.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Donotblocklightemanatingfromproductinwholeorpart,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lensmustbecleanedonregularbasis.
• Entire fixture may become extremely hot. Do not touch hot
lensorfixturebody.Donottouchthelampatanytime.Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
markedonfixturelabel.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turnoff/unplugandallowtocoolbeforereplacinglamp.
LampgetsHOTquickly!Contactonlyswitch/plugwhen
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keeplampawayfrommaterialsthatmayburn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations · Additionally suitable for mounting within 4 ft. of the ground
IMPORTANT LISTINGS AND CERTIFICATIONS
NS - Nite Star™
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
Pleaserefertothelowvoltagedesignguideatwww.bklighting.com/lvguidebeforeinstallationforproperwireselection.

RELEASE
7-15-16
REFERENCE NUMBER
INS000929.1
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
NS™ / NSII™ / DS™ / SH™ FLOODLIGHT
Low Voltage Halogen
Standard Installation
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
Fixture Installation with Standard Knuckle
1. Mount knuckle onto suitable enclosure
according to designed lighting plan.
2. Secure ½” NPS stem to mounting option. Secure
withprovidedlocknutifapplicable.
3. Make watertight connections from remote
transformer to lamp leads using waterproof
wire connectors (By Others). See wiring
diagram.
4. Use 5/32” Allen wrench to slightly loosen #10-
32 stainless steel black oxide socket head cap
screw at the knuckle for aiming purposes.
Tighten to secure desired location.
LINE 12V
Fixture
COM
Remote
Transformer
COM
WIRING DIAGRAM
For use with 12VAC remote transformer.

RELEASED
10-31-13
REFERENCE NUMBER
INS000004
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
LED / Low Voltage Halogen
2-1/4” Size
RE-PLACING LED BOARD/DRIVER AND OPTICS
1. Use 5/64” Allen wrench to loosen #8-32
stainless set screw and remove cap.
4. Disengage LED board and driver assembly.
Replace with new board and driver assembly.
5. Reverse install LED board and driver.
6. With flat head screw driver rotate dial to
desired lumen output. Replace cap.
2. Space three fingers evenly around the optic
and gently rock optic to remove.
3. Use 5/64” Allen wrench to remove two (2)
#2-56 socket head cap screws on LED board,
grasp LED board and gently pull up to expose
quick disconnect.
TO CHANGE LUMEN OUTPUT (WHEN REQUIRED)
1. Use 5/64” Allen wrench to loosen #8-32
stainless set screw and remove cap.
3. Place cap on fixture and tighten set screw.
Tighten screw to 1/2 inch pounds. Top of
screw should sit flush with fixture cap.
2. With flat head screw driver rotate dial to
desired lumen output.
This product is available with Adjust-e-Lume® (Patent Pend.) for DynamicLLumen Output Control
Warning! The light output of this product may be dynamically adjusted as desired to raise and lower light levels. Please ensure the xture is set
to the appropriate light level desired during installation.
Warning: Do not over tighten set screw.
Doing so will compromise O Ring seal and
will void warranty.
TECHNOLOGY
with
TECHNOLOGY
LAMP INSTALLATION OR RE-LAMPING IF REQUIRED FOR LOW VOLTAGE HALOGEN LAMPS
1. Use 5/64” Allen wrench to loosen #8-32
stainless set screw and remove cap.
1A. Or unscrew lens assembly and install lamp
per step 2.
3. Place cap on fixture and tighten set screw.
Tighten screw to 1/2 inch pounds. Top of
screw should sit flush with fixture cap.
Warning: Do not over tighten set screw.
Doing so will compromise O Ring seal and
will void warranty.
2. Firmly insert lamp pins into socket to make
connection. Rocking motion may be required.
Do not exceed the maximum wattage listed
on the fixture label before installing.
Replacement / Installation Instructions

RELEASED
1-31-14
REFERENCE NUMBER
INS-2097-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
Warning Hot Surface
TOOLS
NEEDED:
By Others
5/32” & 5/64” Allen wrench
360SL™ Mounting System
Standard Adjustment
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
NationalElectricalCode,CanadianElectricalCode,andallLocal
andProvincialCodes.
• Followproductlabelinformationandinstructions.
• QualifiedPersonnel mustperform allservicing orrelamping of
thisproduct.
• Beforewiringtopowersupplyandduringservicingorrelamping,
turnoffpoweratfuseorcircuitbreakerbeforeservice.
• The use of accessory equipment not recommended by the
manufacturerorinstalledcontrarytoinstructionsmaycausean
unsafecondition.Theuseofdamagedcomponentsmaycause
anunsafeconditionandvoidproductwarranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Donotblocklightemanatingfromproductinwholeorpart,
asthismaycauseanunsafecondition.
• Never operate the fixture with missing or damaged lens.
Lensmustbecleanedonregularbasis.
• Entire fixture may become extremely hot. Do not touch hot
lensorfixturebody.Donottouchthelampatanytime.Use
aclean,dry,softclothtohandlethelamp.Oilfromskinmay
damagethelampandcauseittorupture.
• Replace lamp only with correct wattage and type of lamp
markedonfixturelabel.
• All gaskets, O-rings and sealing surfaces must be kept clean
duringinstallationandservice;failuretodothismaycausean
unsafeconditionandvoidproductwarranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
LightedlampisHOT!
WARNING-ToreducetheriskofFIREORINJURYTOPERSONS:
Turnoff/unplugandallowtocoolbeforereplacinglamp.
LampgetsHOTquickly!Contactonlyswitch/plugwhen
turningon.
Donottouchhotlens,guard,orenclosure(seediagram/
picture).
Keeplampawayfrommaterialsthatmayburn.
Donotouchthelampatanytime.Useasoftcloth.Oil
fromskinmaydamagelamp.
Donotoperatetheluminairefittingwithamissingor
damagedshield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations · Additionally suitable for mounting within 4 ft. of the ground
IMPORTANT LISTINGS AND CERTIFICATIONS
360SL™ Knuckle
2. Rotate fixture at base and aim fixture to desired
horizontallocation.
3. Use 5/32” Allen wrench to loosen #10-32 stainless
steel black oxide socket head cap screw at the
knuckleforverticalaimingpurpose.
1. Use 5/64” Allen wrench to slightly loosen two (2)
#8-32stainlesssteelsetscrewsonthestemfor360°
aimingpurpose.
4. Tighten two (2) #8-32 stainless steel set screws on
stemtosecurehorizontalaimingposition.
 Tighten #10-32 stainless steel black oxide socket
head cap screw to 15” minimum to 30” maximum
poundstosecureverticalaimingposition.
Warning: Do not over tighten set screw. Doing
so will compromise O-ring seal and will void
warranty.