BABY DELIGHT Beside Me BD06120 Manual

1
©2020 Baby Delight, Inc. 1-401-333-6800 www.babydelight.com
MADE IN CHINA
BD06120
Beside Me
™
Wink
Bedside Sleeper and Bassinet
Middle support
frame (2pcs)
Sleeper frame
Bottom support bar Middle support bar Middle support bar
knuckles
Front and
back feet
Mattress and
waterproof sheet Anchors
Check that you have all the parts for this model BEFORE assembling your product.
If any parts are missing, call Customer Service.
Care & Instructions
Contents
Read all instructions BEFORE assembly and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE. Prior to using the product, check
that the product and all parts were not damaged during delivery. Use
from birth until infant begins to push up on hands and knees, can roll
over, or has has reached 20 lbs (9.1 kg), whichever comes rst.
Anchors to adult bed for
added security in bedside
sleeper mode
Breathable
mesh walls
7-position
height
adjustment
7-position
height
adjustment
Zip down panel
Removable &
washable cover

2
WARNING
FAILURE TO FOLLOW THESE WARNINGS AND THE INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH. DO NOT USE THIS
PRODUCT IF YOU CANNOT EXACTLY FOLLOW THE INSTRUCTIONS
THAT COME WITH IT. THIS PRODUCT SHOULD BE FULLY
ASSEMBLED PRIOR TO USE.
SUFFOCATION HAZARD
Infants have suocated:
• In gaps between extra padding and side of the bassinet, and
• On soft bedding.
• Use only the pad provided by Baby Delight, Inc..
• Never add a pillow, comforter, or another mattress for padding.
• If a sheet is used with the pad, use only the one provided by Baby Delight, Inc..
• Ensure that the side panel is locked when child is left unattended.
• Never leave infant in bassinet with side down unless it is securely positioned in
sleeper mode attached to the adult bed with anchors securely in place.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on
their backs to sleep, unless otherwise advised by your physician.
ENTRAPMENT HAZARD:
• To prevent death from entrapment, bedside sleeper must be properly secured to
adult bed using the attachment system.
• To avoid death from the infant’s neck being caught on the top rail on the side that
is next to the adult bed, the top rail must be no higher than the adult
bed mattress.
• There must be no more than 1/2 inch (13mm) gap between bedside sleeper and
adult bed.
• Check tightness before each use by pulling bedside sleeper in a direction away
from adult bed.
• If gap exceeds 1/2 inch (13mm), DO NOT use product. Do not ll the gap with
pillows, blankets or other items that are suocation hazards.
• Always read and follow assembly instructions for each product use mode (bedside
sleeper/bassinet).
• Always use ALL required parts for each use mode (bedside sleeper/bassinet).
• Check instruction manual for a list of required parts. Regularly check product
before each use for loose, damaged, or missing parts. DO NOT use it if any part
is loose or missing, or if there are any signs of damage. DO NOT substitute parts.
Contact Baby Delight, Inc. if replacement parts or instructions are needed.

3
NEVER USE THIS PRODUCT IN BEDSIDE
SLEEPER MODE WITHOUT THE ANCHOR
PLATES SECURELY ATTACHED TO THE
ADULT BED
MATTRESS, BOXSPRINGS
& FRAME ALIGNED
ACCEPTABLE BED
FRAME IN-LINE
FRAME
EXTENDED
UNACCEPTABLE BED,
MATTRESS, BOXSPRING &
FRAME NOT IN-LINE
• ALWAYS raise side with zipper (completely closed) to use bassinet mode.
• ALWAYS push adult mattress against bedside sleeper after securing to bed with
safety strap and anchor plates.
• NEVER leave infant in bassinet mode with sides down. Ensure that the side panel is
locked/zipped when child is left unattended.
• This bedside sleeper is designed for use only with adult beds that are between
17”– 25”(43cm – 63cm) from oor to top of adult mattress.
• The anchor plate and straps assembly must always be used in bedside sleeper
mode. Product in bedside sleeper mode must be tightly attached to adult bed
mattress to ensure safe use.
• It is recommended to make the strap shorter than the width of the mattress to
ensure bedside sleeper is pressed securely against the adult bed, without
any gaps.
• A bedside sleeper is designed to provide a sleeping area for an infant until he or
she begins to push up on hands and knees or approximately 5 months of age. Move
your child to another sleeping product when your child reaches this stage.
SUFFOCATION, ENTRAPMENT
AND FALL HAZARDS:
WARNING - CONTINUED
FALL HAZARD:
• To help prevent falls, do not use this product when the infant begins to push up on
hands and knees, can roll over or has reached 20 lbs., whichever comes rst.
• Always use all required parts for each use mode (bedside sleeper/bassinet).
• Strings can cause strangulation! NEVER place product near window blinds or patio
doors with cords where a child could reach the cord and be strangled, or hang
strings over the product or place items with a string around an infant’s neck such
as hood strings or pacier cords or attach strings to toys.
• DO NOT place any cord or strap or similar item in or near this product that could
become wrapped around a child’s neck.
• In Bassinet Mode - Assure Side Panel is locked.

4
Assembly/Operating Instructions
Assembling the bassinet:
1 2
Lay the SLEEPER FRAME face down
on a flat surface.
Holding the CENTRAL SUPPORTING
STRUCTURE, open both of the
LEGS outward.
Plug in FRONT AND BACK FEET (2
sets) into SLEEPER FRAME LEGS by
lining up the buttons and holes on the
inside of the legs until you hear a click.
The FEET should sit flat on the floor
when the BASSINET is upright.
3
Plug in MIDDLE SUPPORT BAR
KNUCKLES to FRAME on each side
matching the engraved “L” and “R” on
the KNUCKLES to the “L” and “R” on
the FRAME.
4
Insert MIDDLE SUPPORT BAR into
FRAME on each side until you hear a
click. NOTE: You may need to spread
the FRAME slightly to insert the
MIDDLE SUPPORT BAR.

5
Assembly/Operating Instructions - Continued
CLICK!
7
Push MIDDLE SUPPORT BAR into the
KNUCKLES until you hear a click. Make
sure both sides are secured.
Insert the SIDE RAIL into the MIDDLE
SUPPORT FRAME, by lining up the
buttons and holes, until you hear
a click.
CLICK!
6
5
Insert BOTTOM SUPPORT BAR up into
the FRAME until it is snapped in.
Lift FRONT PANEL FABRIC over
the MIDDLE SUPPORT FRAME AND
INSERT into fabric pocket. Secure
fabric to FRAME with 4 loop fasteners.
8

6
Assembly/Operating Instructions Continued
1
Height adjustment of the bassinet:
The BASSINET has 7 height positions.
Press the HEIGHT ADJUSTER BUTTONS
on the top and side of the frame on each
side to lift or lower the BASSINET until
a you hear a click. ALWAYS make sure
the BASSINET IS ADJUSTED to the same
height (by looking at the numbers) on
each side.
The BEDSIDE SLEEPER is designed
for use only with adult beds that are
between 17” and 25” (43cm – 63cm)
from floor to top of adult mattress.
9
Once the FRAME is secure, place
the MATTRESS with SHEET into the
BASSINET with the curved edge of the
MATTRESS facing the curved edge of
the BASSINET.

7
Bedside sleeper mode (attaching to the bed):
Bedside Sleeping Mode
THIS METHOD IS ONLY POSSIBLE WITH BED TYPES THAT COMPLY WITH ALL
OF THE CONDITIONS DESCRIBED IN THIS PARAGRAPH.
IN PARTICULAR, THE SIDE SUPPORT OF THE BEDSIDE SLEEPER SHOULD
ALWAYS BE PUT CLOSE TO THE PARENT’S MATTRESS AND THE MATTRESS
SHOULD ALWAYS BE ALIGNED WITH THE HEIGHT OF THE SIDE SUPPORT
FOR RESTRAINT OF THE BEDSIDE SLEEPER. FURTHERMORE, THE BEDSIDE
SLEEPER SHOULD BE FIRMLY FIXED TO THE STRUCTURE OF THE PARENT’S
BED OR TO THE MATTRESS SUPPORT.
CHECK TO MAKE SURE THAT THE BEDSIDE SLEEPER IN THE BEDSIDE
SLEEPER MODE DOES NOT INTERFERE WITH THE PARENT’S BED.
DURING USE, MAKE SURE THAT THE PARENT’S BED SHEETS, BLANKETS ETC,
DO NOT ENTER AND COVER THE INTERIOR OF THE BEDSIDE SLEEPER.
WARNING - IMPORTANT FOR
THE SAFETY OF YOUR CHILD:
WARNING!
WARNING!
1
Unzip the SIDES of the BEDSIDE
SLEEPER until they are
completely unzipped.
Slide the TOP BAR LOCK LEVER away
from the top bar and lift TOP BAR out
of GROOVE on both sides and
fold down.
2

8
6. Tighten the LOOP by pulling the BELTS firmly. Adjust the ANCHOR STRAPS
separately until the BEDSIDE SLEEPER is firmly in contact with the
parent’s mattress.
NEVER USE THIS
PRODUCT IN
BEDSIDE SLEEPER
MODE WITHOUT
THE ANCHOR
PLATES SECURELY
ATTACHED TO THE
ADULT BED
ENSURE THE ANCHORS ARE STRAIGHT.
WARNING:
Bedside Sleeping Mode - Continued
3. Move the bedside sleeper close to the parent’s bed and check the height of the
BEDSIDE SLEEPER compared with the mattress on the bed. The SIDE SUPPORT
of the sleeper should always be placed close to the parent’s mattress and the
mattress should always be aligned with the height of the SIDE SUPPORT for
restraint of the sleeper.
4. In order to attach the bedside sleeper to the parent’s bed in BEDSIDE SLEEPER
mode, use the attached pair of ANCHORS provided.
5. Slide the ANCHORS between the top mattress and the base across the
opposite side of the bed using a back and forth ‘sawing’ motion and at the same
time pulling downward until the STRAPS and ANCHOR PLATES are in the
desired position.
IN THE BEDSIDE SLEEPER MODE THE TWO LEGS OF THE BEDSIDE SLEEPER
SHOULD ALWAYS BE ADJUSTED TO THE SAME HEIGHT.
WARNING:

9
Care & Cleaning - Continued
Removing the cover:
1
Remove the MATTRESS and release the
hook and loop tabs from the MIDDLE
SUPPORT FRAME on the underside of
the bassinet.
2
Release the hook & loop tabs from the TOP RAIL COVER of the bedside sleeper
as per image. Locate the ZIPPER underneath the FABRIC LIP of the structure
and unzip.
3
Gently remove the LINING from the UPPER TUBULAR STRUCTURE, making sure
not to damage the internal part of the LINING.

10
www.babydelight.com
©2020 Baby Delight, Inc. 1-401-333-6800 [e-mail]
BD06120
Limited Warranty
At Baby Delight, Inc. we make innovative and high quality products for babies,
children and their parents. We warrant this product to be free from defects in
material and workmanship existing at the time of manufacture for a period of
90-days from the date of initial purchase (sales receipt is required for proof of
purchase). If such a defect is discovered during the limited warranty period, we
will, at our sole option, repair or replace your product at no cost to you.
This limited warranty does not cover claims resulting from misuse, failure to
follow the instructions on installation, maintenance and use, abuse, alteration,
involvement in an accident, and normal wear and tear.
DO NOT use bedside sleeper if any parts are missing, damaged, or broken.
Contact for replacement parts and instructional literature if needed. DO NOT
substitute parts.
For warranty service or replacement part information:
USA: Please call Customer Service at 1-401-333-6800, email at
[e-mail], or mail 30 Martin Street, Suite 3C, Cumberland,
RI 02864.
How to Care for Your Beside Me™Wink
Maintenance:
The BASSINET and the MATTRESS have a stain resistant FABRIC COVER which is
completely removable and washable.
The removal of the fabric should be carried out by an adult only. On a regular
basis check the condition of the product and presence of any possible damage.
In the case of damage do not use and keep it out of the reach of children.
Cleaning:
Do not use solvents, abrasives or aggressive products. After each wash check
the resistance of the fabric and the stitching. For washing of the fabric, carefully
comply with instructions indicated on the label.