Baby Love Baby Capsule User manual

1
Baby
Capsule
IMPORTANT:
KEEP THIS BOOKLET IN
THE PLACE PROVIDED ON
THE CHILD RESTRAINT
CLICKTIGHT compatible

QUICK SETUP GUIDE
• REARWARD FACING SEATBELT 04
MEET YOUR CHILD SEAT 10
IMPORTANT INFORMATION AND WARNINGS 12
SHOULDER HEIGHT MARKERS 14
OUTGROWN YOUR CHILD SEAT 16
CHILD SEAT SUITABILITY GUIDE 17
Rearward Facing
HOW TO INSTALL IN AN AIRCRAFT 42
Aircraft
Setup
BRITAX STROLLERS 45
CARE AND MAINTENANCE 46
• CLEAN HARNESS BUCKLE 47
• REMOVE COVER 49
• REPLACE COVER 52
ACCESSORIES 55
INSTALLATION OF VEHICLE UPPER ANCHOR POINT 58
IN CASE OF ACCIDENT 64
WARRANTY 66
Care & Maintenance
REARWARD FACING SEATBELT
INSTALLATION VIDEO
Contents
CHILD SEAT FEATURES - REARWARD FACING 18
SETUP
• GENERAL INFORMATION 21
• ADJUSTING THE BASE ANGLE 22
• INSTALLING INTO YOUR VEHICLE 24
• TOP TETHER 27
• ADJUSTING HANDLE POSITION 30
• HARNESS FEATURES 31
• CROTCH STRAP 32
• LAP STRAP 33
• SETTING UP THE HARNESS 34
REMOVE CHILD FROM CAPSULE 39
REMOVE CAPSULE FROM VEHICLE 40

15
4 5
Close ClickTight
REMOVE
SLACK
Attach tether clip
NO
TWISTS
8.
2. 10.
4. 12.
6. 14.
1. 9.
3. 11.
5. 13.
7. 15.
Lift
Press and hold Recline
Adjustment button
Adjust foot
up/down
and check
indicator.
Check foot
is locked.
Squeeze button and open
ClickTight
NO
TWISTS
Engage
Buckle
Securely
Check base
is secure
Lock capsule
onto base Lengthen
Top Tether
Push
B
Pull
A
Quick Setup Guide - Rearward Facing Seat Belt Install
Quick Setup Guide - Rearward Facing Seat Belt Install
Hey!
before you install me...
Don’t forget to note your
serial number found on
the seat to complete your
warranty registration.
Ensure
secure
Place top
tether loop
around
capsule
and
through
guide
PINCH POINT UNDER HANDLE

15
6 7
Remove
slack
Pull
Pull to
tighten
NO
SLACK
16. 17.
1. 2.
Store strap
Harness Straps Not Below Green Zone
CPress
Remove straps from yoke
3. 4.
Pull
through
cover
Choose
correct
slot
Quick Setup Guide - Rearward Facing Seat Belt Install
Quick Setup Guide - Rearward Facing Child Install
Press
A
BPull
Under
Capsule
Low Birth
Weight Infant
Growing
Infant
Average
Newborn Infant
Larger
Infant
18. You have now successfully
completed the seat belt
installation .
Check angle of child seat is
still correct.

15
8 9
Lengthen
Top Tether
Install child &
check shoulder
height.
Push
B
Pull
A
Remove
slack
Pull
Pull to
tighten
NO
SLACK
Store strap
Replace
straps to
yoke
NO
TWISTS
ALWAYS ENSURE BUCKLE
IS SECURE.
REMOVE SLACK AND
TWISTS FROM HARNESS
AND TOP TETHER.
5.
15.
7.
17.9.
11.
13.
6.
16.
8.
10.
12.
14. Attach tether clip
NO
TWISTS
Quick Setup Guide - Rearward Facing Child Install
Quick Setup Guide - Rearward Facing Child Install
Lock capsule
onto base
Ensure
secure
Place top
tether loop
around
capsule
and
through
guide
Crotch Strap Options Lap Strap Options
AVERAGE
NEWBORN
INFANT LAP
LOW BIRTH
WEIGHT LAP
TOO
HIGH
TOO
LOW

15
10 11
Meet Your Child Seat Meet Your Child Seat
Suitable for low birth weight and premature infants without
restrictive medical conditions. To be used only in a rearward-
facing position until the infant's shoulders reach the shoulder
height marker (approximately 12 months of age).
Continue to use this infant restraint until the child reaches this limit.
Infants are at risk of serious injury if they face forward too early.
No child restraint can guarantee absolute protection from
injury in every crash. However, to ensure that your child gets
all the protection designed into the restraint, PLEASE READ AND
FOLLOW THESE INSTRUCTIONS EXACTLY and use only Safe-n-Sound
recommended parts and accessories.
Carefully read all the instructions for installation in this book. If in
doubt about the method of installation, consult Britax childcare or
agent or a child restraint tter or, in New Zealand, to consult the
agent for the vehicle.
适用于没有严格医疗条件的低出生体重婴儿和早产儿。只采用后向式安装，
直到婴儿的肩膀达到肩高标记（大约12个月的宝宝）
在儿童达到该座椅上限以前必须不断使用这一婴儿汽车座椅。
婴儿过早乘坐前向式座椅则可能受到严重的伤害。
Phù hợp với bé sơ sinh nhẹ cân và bé sanh thiếu tháng không có tình
trạng sức khỏe giới hạn. Chỉ được sử dụng ở vị trí hướng mặt về phía sau
cho đến khi vai của bé cao tới vạch ghi độ cao của vai (khoảng 12 tháng
tuổi).
Hãy tiếp tục sử dụng ghế em bé này cho đến khi em cao tới giới hạn này.
Bé sơ sinh có nguy cơ bị chấn thương nghiêm trọng nếu hướng mặt về
phía trước quá sớm.
The baby capsule and base is installed so that the infant is facing
rearwards. This provides best position in a crash for infants.
This baby capsule provides the ability to t low birth weight or
premature babies and has been tested to verify its capability.
Babies and children below 4 years old must not sit in the front seat
of a vehicle unless allowable by the Regional Road Rules
Check your local Regional Road Rules.
Always store the instruction book in the place provided in the base
when the baby capsule is removed.
This baby capsule is compatible with various Steelcraft,
Safe-n-Sound and competitor strollers. For detailed compatibility
refer to www.britax.com.au.
Britax Childcare Pty Ltd continues to provide care for your children
when traveling in motor cars with a range of child restraints
suitable throughout their childhood.

15
12 13
Important Information And Warnings Important Information And Warnings
• Use the restraint exactly as shown in the instructions.
• Supervision of children is needed because they may be able
to undo the buckles and adjusters.
• DO NOT LEAVE CHILDREN UNATTENDED IN THE CAR.
• Do not alter or modify this restraint.
• Repairs must only be done by the manufacturers or agent.
• Fit the restraint rmly to the car seat.
• Fit the harness rmly to the child.
• A loose restraint or harness is dangerous.
• DO NOT USE A REAR-FACING CHILD RESTRAINT WHERE AN
AIRBAG IS FITTED IN FRONT OF THE SEATING POSITION. For other
airbags, refer to the car owner’s handbook for warnings and
instructions.
• To ensure infant’s back is evenly supported do not put more
than one nappy on the baby and make sure the nappy is not
thickly folded at the back.
• Do not allow the restraint to come into contact with polishes,
oils, bleach and other chemicals.
• Destroy the restraint if it has been in a severe crash, even if no
damage is visible.
• Do not harness an infant wrapped in a blanket or swaddled.
Any blanket or wrap must only be placed over the harness
and infant.
• Always secure the loose end of the top tether strap. Do not
use the child restraint where this strap may fall into the seat
back or off the side of the seat.
• ALWAYS ATTACH HOOK AND REMOVE SLACK.
• DO NOT USE THIS RESTRAINT WITHOUT THE COVER.
IMPORTANT :
• TO BE USED WITH A LAP-SASH OR LAP-ONLY SEATBELT IN THE
BACK OF MOST CARS WITH FORWARD FACING SEATS
• THIS RESTRAINT MUST BE ATTACHED TO A CHILD RESTRAINT
UPPER ANCHORAGE POINT IN THE CAR. REFER TO CAR OWNER’S
HANDBOOK FOR LOCATION OF UPPER ANCHORAGE POINTS. REFER
TO A CHILD RESTRAINT FITTING STATION IF NO UPPER ANCHORAGE
POINTS ARE IN THE MOTOR CAR.
• THIS RESTRAINT IS NOT SUITABLE FOR USE WHERE THE TOP TETHER
STRAP MAY FALL INTO A SPLIT IN THE SEAT BACK OR OFF THE SIDE
OF THE SEAT.
• Always attach the top tether strap to the child restraint and
upper anchorage in your car before each journey.
• This child restraint is not approved for use with any
connectors that connect to the car’s ISOFIX low anchorages.
• Seatbelt extenders are not recommended to be used if the
seatbelt is not long enough to secure the child restraint. If
seatbelts are too short then seek advice from a child restraint
tter and consider their recommendations before using a
seatbelt extender, ensure that the seatbelt or extender buckle
does not enter the seatbelt path or prevent the capsule
locking onto the base.
• Ensure babies and toddlers are adequately shaded from
direct sunlight through side and rear windows.
• Check the car is ventilated by opening windows or using the
car ventilation system to introduce fresh air. The recirculation
setting is not suitable to provide ventilation.
• The restraint should not be purchased or sold as a second
hand item. It is recommended not to use child restraints
older than 10 years as the protection in an accident may be
reduced.

15
14 15
Shoulder Height Markers Shoulder Height Markers
Britax recommends using
this restraint in rearward
facing as long as possible.
A Shoulder Height Marker is featured on this baby capsule. This
is an indicator for when your infant has outgrown the seat and it
should be superseded.
Height Marker
If your child’s shoulders are above the height marker, they have
outgrown the seat.
IMPORTANT: Follow this advice.
Older Baby
(Rearward Facing)
Newborn
(Rearward Facing)

15
16 17
Outgrown Your Child Seat
When your child has outgrown this seat, you can use:
• Dedicated Forward Facing Seat with
in-built harness: Suitable for children
who have outgrown their Baby Capsule
(from approximately 6 months old),
up to approximately 4 years of age,
or 8 years of age depending on the
restraint.
Child Seat Suitability Guide
These child restraints, when used correctly, allow the driver to meet
the Australian Road Rules in each state.
• A convertible booster seat
with in-built harness until
approximately 4 years
old and then as a booster
seat with vehicle lap-sash
seatbelt until approx 6 to
8 years of age (or seatbelt
and compatible child
harness).
• Convertible Child Seat: Suitable from
approximately 12 months, continue
to keep your child rear facing until the
shoulders reach the lower shoulder height
marker. Then turn to forward facing until
the child reaches the upper shoulder
height marker - approximately 4 years of
age.
Some convertible child seats may allow
for the child to remain rearward facing
until 2 to 3 years of age.

18 19
Harness
adjuster
button
located
under
cover
2. Shoulder height
markers
1. Carry Handle
4. Shoulder Pads
5. Infant Insert
10. Harness
7. Harness Adjuster
Button
8. Harness
Adjuster
Strap
9. EZ Buckle 6. Release Buckle
(Red button)
3. Buckle tongue
holders
11. Seat cover
12. Handle
Release
Button
Child Seat Features - Rearward Facing Child Seat Features - Rearward Facing
13. Rebound Bar
14. Rearward
Facing
Belt Path (Blue)
15. Level Indicator
16. Instruction
Manual
Storage
17. Recline
Adjustment
Foot
18. ClickTight
Handle
19. ClickTight
Button
20. Recline
Adjustment
Button

20 21
Child Seat Features - Rearward Facing
Front of
vehicle
22. Vehicle’s
Anchor
Fitting
26. Long or short
Vehicle Seat
Protector
(If supplied)
21. Attachment
Clip
28. Top Tether
Storage Pocket
29. Top Tether
Adjuster
23. Top Tether
Adjuster
Strap
27. Top
Tether
Setup - General Information
Child seat upper anchorage point
This child seat must be installed using the top tether. The top
tether will need to attach to the appropriate upper anchorage
point for rearward facing mode. Refer to the car owner’s
handbook for anchorage locations or points. If your vehicle does
not have an upper anchorage point then you will need to install
an upper anchorage point. Refer to pages 58 to 63.
Is there enough room?
THE TETHER STRAP MUST ALWAYS BE
FITTED WHEN THE CHILD RESTRAINT IS
USED IN A VEHICLE.
Do not use the restraint without the
top tether strap correctly attached.
DO NOT USE A REAR FACING CHILD
RESTRAINT WHERE AN AIRBAG IS FITTED
IN FRONT OF THE SEATING POSITION.
Do not use on any vehicle seat
which faces sideways or rearwards.
The Baby Capsule may just touch the front seat, but must not in
such a way that the installation angle is affected.
Do not allow the front seat to alter the installed angle of the
restraint.
24.Top Tether Guides
25. Capsule Release Lever
(from Base or Stroller)
12. Release
Handle
To ensure that the
space is sufcient, the
purchaser should check the
measurements between the
vehicle’s rear and front seats
in which the child restraint is
intended to be used.
717mm
355
mm
Width 420mm

22 23
Lift
Setup - Adjusting the Base Angle Setup - Adjusting the Base Angle
Adjust the base until
the entire blue marker
is completely visible
between the two lines
while on the vehicle seat.
Check and adjust the base
if necessary.
Place the base on vehicle
seat in a seating position
where a child restraint
anchor tting is installed.
The Level Indicator shows when your child seat is installed at the
correct angle for your vehicle. It gives you condence the child
seat is positioned correctly whenever you travel.
1.
5.
3.
2.
4.
Pull up and hold the
release lever on the back
of the capsule. Lift the
capsule up from the base
using the carry handle.
If your car’s seat is
contoured then you may
need to adjust the angle
of the base so your baby is
not too upright.
Do not have the base too
far away from the vehicle
seat.
Some vehicle seats have more slope than others. If the
correct Base Angle cannot be achieved using the Recline
Adjustment Foot (Figure A), it may be necessary to
adjust the angle by placing a rm packing between the
underside of the base and the vehicle seat (with recline
foot stored).
Packing can be a rmly rolled towel.
If packing placement is needed similar to Figure B, ensure
the packing cannot become dislodged.
Always ensure any packing is trapped and cannot
become dislodged during normal use.
Always check that the level indicator conrms the correct
installation angle.
Figure .A.
Press and hold Recline
Adjustment button
Adjust foot
up/down
Figure .B.

24 25
Lift
Setup - Installing Into Your Vehicle Setup - Installing Into Your Vehicle
Grab the ClickTight handle
and squeeze the button.
Lift to open the ClickTight
handle.
Press the base rmly into
the vehicle seat while
removing slack from the
vehicle seat belt.
NOTE: Do not tighten.
ALWAYS REMOVE SLACK
FROM SEATBELT.
Place the base on the
vehicle seat.
Refer to page 22 to 23 to
adjust recline angle.
Thread the seat belt under
the ClickTight and through
the blue REARWARD FACING
BELT PATH guide.
NOTE: Ensure the seatbelt is
tucked under the ClickTight
completely. Do NOT thread
seatbelt through ClickTight
handle
1. 5.
3. 6.
2.
4. 7.
Pull up and hold the
release lever on the back
of the capsule. Lift the
capsule from the base
using the carry handle.
Lengthen vehicle seatbelt.
NOTE: Ensure the vehicle
belt is not twisted.
Engage the vehicle seatbelt
buckle and tongue without
twists.
ENSURE THERE ARE NO TWISTS IN SEATBELT.
Close the ClickTight by
pushing down on the
ClickTight handle.
Ensure window is entirely
green.
PINCH POINT
UNDER HANDLE

26 27
Setup - Installing Into Your Vehicle Setup - Top Tether
Place top tether loop
around capsule and
through guide.
Lock the capsule onto the
base.
Lift the carry handle to verify
attachment.
Handle may be rotated to
other latched positions as
desired (see page 30).
8. 1.
10.
2.
9.
3.
Check vehicle seatbelt is
tight and not twisted, and
base is secure.
You have now successfully
completed the seat belt
installation.
You are now ready to install
the top tether. Connect top tether
attachment clip to vehicle
anchor tting.
Check your vehicle manual
for the correct anchor
ttings in your vehicle
Lock capsule
on base
A LOOSE INSTALLATION IS
DANGEROUS.
top tether
Pull
Push
C
Lengthen strap
A
B
A. Press top tether adjuster
button.
B. Lengthen top tether
strap fully, ensure all
unnecessary twists are
removed.
C. Place the top tether over
the vehicle seatback,
and if needed, remove
the vehicle headrest. If
you cannot remove the
headrest, then ensure that
the top tether straps are
placed on the outer-sides
of the headrest.
Attach
Ensure
secure

28 29
Setup - Top Tether
Setup - Top Tether
4.
5. 6.
Remove
slack
Pull
Pull to tighten Ensure slack is removed
from the top tether straps
by pulling top tether
adjuster strap. Do not over
tighten as it may cause
your child seat to lift.
ALWAYS REMOVE SLACK IN
THE TOP TETHER AND STORE
STRAP.
ENSURE THE TOP TETHER
STRAPS ARE NOT TWISTED.
Store
strap
Store
strap
Roll up any excess strap
and store in the pocket
provided on the top tether
strap.
Check angle of child
seat is still correct.
(See page 22 to 23).
CAUTION: CHILDREN CAN BE INJURED OR
RESTRAINTS AND TOP TETHER STRAP DAMAGED
BY UNSECURED CARGO IN A COLLISION. SECURE
OR REMOVE HAZARDOUS CARGO BEFORE USING
THIS CHILD RESTRAINT.
The top tether strap must be tted at all times.
Always secure the loose end of the top tether strap to prevent it
hanging out of the car or being accessible by the child.
THIS RESTRAINT IS NOT SUITABLE FOR USE WHERE THE TOP TETHER
STRAP MAY FALL INTO A SPLIT IN THE SEAT BACK OR OFF THE SIDE OF
THE SEAT.
ALWAYS ATTACH TOP TETHER HOOK AND
REMOVE SLACK IN THE TOP TETHER STRAP.
IMPORTANT:

30 31
Setup - Adjustment Of Handle Position Setup - Harness Features
The carry handle is designed to rotate in 3 positions as below.
The capsule can be used without the base to convert it to a
rocker. At the base of the handle there are two large buttons
which control the three positions of the handle.
To adjust, press and
hold both carry handle
adjusters and rotate the
handle to the desired
position.
Ensure the handle
is locked in position
securely.
Do not place the Baby Capsule on a table or a work-top where it
could fall off.
Check the Baby Capsule handle is latched properly every time
you pick up the Baby Capsule, lock it onto the base or use it with
a stroller.
IMPORTANT :
1
Carry Position Rocking Position Non-Rocking
Position
1. Harness Adjuster Strap
2. Crotch strap and slots
3. Lap strap and slots
4. Shoulder strap and slots
5. Shoulder height marker.
For Low Birth Weight Babies
This Baby Capsule is supplied with harness setup to suit an
average newborn infant birth weight.
Assess the harness tment and adjust as necessary by following
Setting Up The Harness, see page 34.
However, if your child is of low birth weight or premature then
you may need to reposition the harness to the "low birth weight"
position, as follows:
Move the crotch strap to the inner slot (see page 32), the lap
straps to the inner slots (see page 33) and the shoulder strap
to the nearest slot above the shoulders (see page 35). This will
provide better support for a low birth weight infant.
1
2
3
4
5
Press and hold

32 33
Setup -Crotch Strap Setup - Lap Strap
Remove baby from capsule and
capsule from base prior to making
adjustments.
A. Turn each metal 3-bar slide and
push back through the slots as
shown.
B. Insert each metal 3-bar slide
through the preferred lap strap
slot.
For low birth weight feed from
inner slot to middle slot.
For average newborn feed from
outer slot to middle slot.
Lap straps metal 3-bar slides
are always to be looped to the
middle slot.
When replacing straps, ensure the straps are
not twisted and that all straps are secure.
Adjustment of Lap Strap
LARGER INFANT
AVERAGE
NEWBORN INFANT
LOW BIRTH WEIGHT This baby capsule is tted with three
crotch strap positions. Correct location
of crotch strap will assist to securely
position the infant and will help prevent
infant from slipping further down the
capsule or slumping.
Crotch Strap Options
Adjustment of Crotch Strap
Example: Remove baby from capsule and capsule
from base prior to making adjustments.
A. Decide which crotch strap position is
preferable.
B. Turn the metal 3-bar slide on its side
and push back through the slots
until the crotch strap is free from the
capsule.
C. Insert the metal 3-bar slide through
the preferred slot and loop the strap
back up or allow to be at full height
(as crotch strap option illustrations
show).
Ensure crotch strap is not twisted and
positions the red buckle button outwards.
The lap straps for an average
birth weight baby outer lap
slot.
A low birth weight baby may
need to use the inner lap
strap slot.
Lap Strap Options
AVERAGE
NEWBORN
INFANT LAP
LOW BIRTH
WEIGHT LAP
AVERAGE
NEWBORN
INFANT LAP
LOW BIRTH
WEIGHT LAP
TOO
LOW
TOO
HIGH
The capsule is tted with two lap strap positions.
NOTE: Move the lap strap to the outer slot as baby grows.

34 35
Setup - Setting Up The Harness Setup - Setting Up The Harness
Press
CPress
B
A
Pull
1.
2. 3.
A. Press harness adjuster
button (located under
trim.)
B. Place your hand under
both shoulder harness
straps, then pull shoulder
harness straps to
lengthen.
C. Disengage the buckle by
pressing the red button.
If your child is less than 3kg then
you will probably need to use the
harness arrangement for smaller
babies.
When positioning baby into
capsule make sure baby's back
is fully supported onto the at
section and the baby's nappy
area (bottom) is resting in the
bottom curvature as shown.
It is recommended that bulky
nappies are not used when baby
is traveling in the Baby Capsule
as they can cause incorrect
positioning of the baby's back in
the Baby Capsule.
Flat
back
rest
Curved seat
Positioning Baby Into Capsule
The Capsule is tted with four shoulder strap positions. Always
adjust the height of the shoulder straps as the child grows.
It is better to change one strap at a time so that the other strap
will be a guide for re-assembly.
The shoulder straps must be in the slots which are nearest to the
child’s shoulders, but not lower than the child’s shoulders.
Remove straps from yoke
At the rear of the Capsule,
remove one of the harness
shoulder straps from yoke by
slipping strap through slot.
Pull the shoulder strap
through cover slot into to
the seating area of the
capsule.
Pull through cover
Harness Straps Not Below Green Zone
Low Birth
Weight Average
Newborn Growing Infant Larger Infant
Adjusting The Shoulder Straps As Child Grows

36 37
4.
5.
Check which slot is most
appropriate for the child’s
height.
Pass shoulder strap back
through desired slot in cover
and corresponding slot
in the shell. The slot MUST
position the shoulder strap
level with or the next slot
above the baby’s shoulder.
Setup - Setting Up The Harness Setup - Setting Up The Harness
Replace straps to yoke Ret the shoulder strap to
the yoke. Repeat steps for
the other strap.
Ensure both shoulder straps
use the same height slot
pairs.
When replacing straps,
cover and padded
insert, ensure none of
the straps are twisted
and that all straps are
secure by pulling each
harness strap.
IMPORTANT :
6.
7.
Place buckle tongues into
buckle tongue holders.
Tongue
Lap strap
Buckle
Shoulder
Strap
Engage Buckle.
ENSURE BUCKLE IS
ALWAYS CONNECTED
DURING USE.
ENSURE ALL HARNESS
STRAPS ARE NOT TWISTED.

38 39
Setup -Removing Child From Capsule
1.
3.
Pull Pull
Push
Lengthen strap
A
A
B
A. Press top tether
adjuster button.
B. Lengthen top tether
strap fully.
A. Loosen shoulder harness
straps by pressing the
harness adjuster button.
B. Pull both shoulder
harness straps evenly.
C. Disengage buckle by
pressing red button.
Place harness buckles in
buckle tongue holder.
Lift child from the child seat.
Press
Press
B
C
Remove all slack from
the lap strap area
(including behind
baby's bottom), by
pulling up on the
shoulder straps.
Pull harness adjuster
strap to tighten.
Ensure a rm but
comfortable t.
ENSURE ALL HARNESS
SLACK IS REMOVED.
Do not harness an infant wrapped in a blanket or swaddled as
this increases the risk of ejection and injury or death in a crash.
The harness needs to t rmly to the baby, any blanket or other
covering may be placed over the harness after it is adjusted. Arms
and legs must be free and not bound or wrapped together. The
legs must sit on each side of the crotch strap.
B
A
Pull
WARNING: DO NOT LEAVE CHILDREN
UNATTENDED IN THE CAR.
8.
Setup - Setting Up The Harness
2.