baby&child 105014 User manual

All Restoration Hardware Bunk Beds are designed to meet the highest safety
standards and comply with all U.S. and Canadian Bunk Beds regulations.
WARNING: Read all
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing
to the address above. Include the product model number, color, and a brief description of the part.
Call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry
cloth. Blot spills immediately and wipe with a clean damp cloth. If the crib is to be stored, store in a cool dry place and
carefully package all original hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen Key (included)
Note: It may be easier to assemble product with two people.
NOTE : When inserting bolts, turn clockwise until tight. Then loosen
12
-
34
of a turn. After bunks is
completely assembled, return to each bolt and tighten. Use wax or soap on all bolts to facilitate assembly.
MODEL NO. 105014
"BELLINA TWIN OVER TWIN
BUNK BED"
Made in Vietnam
Distributed in the U.S.A. by:
Restoration Hardware Baby & Child
11640 Harrel St. Suite B
Mira Loma, CA 91752
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7
Page 1 of 10

Page 2 of 10
IMPORTANT SAFETY INFORMATION FOR BUNK BED
1. Follow the information on the WARNINGS appearing on the upper bunk end structure and on the carton.
2. Always use the specified size mattress or mattress support, or both to help prevent the likelihood of entrapment or
falls.
3. Surface of mattress must be at least 5 inches below the upper edge of guardrails on top bunk.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrails, ladder, and other components are in their proper position, free from
damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Restoration Hardware for replacement parts.
10. Use of a night light may provide added safety precaution for a child using the upper bunk.
11. Use guardrails on both sides of the upper bunk.
12. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should
be placed against the wall to prevent entrapment between the bed and the wall.
13. The use of water flotation mattress is prohibited.
14. STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are not designed for use
with the bed: for example, but not limited to, hooks, belts, and jump ropes
15. Keep these instructions for future reference.
WARNING
To help prevent serious or fatal injuries from
entrapment of falls:
•Never allow a child under 6 years on
upper bunk.
•Use only mattress which is 74"-75" long
and 371/2"-381/2" wide on upper bunk.
•Ensure thickness of mattress and
foundation combined does not exceed
9.5" and mattress is at least 5" below
upper edge of guardrails.
•Use guardrails on both sides of upper
bunk.
•Prohibit horseplay on or under bed(s).
•Prohibit more than one person on upper
bunk.
•Use ladder for entering and leaving
upper bunk.
•STRANGULATION HAZARD - Never
attach or hang items to any part of the
bunk bed that are not designed for use
with the bed; for example, but not
limited to, hooks, bells, and jump ropes.
DO NOT REMOVE THIS LABEL

32 PCS
4 PCS
Page 3 of 10
A LOWER END PANELS 2 PCS
B LOWER SIDE RAILS 2 PCS
C SLAT ROLL 1 SET
D UPPER END PANELS 2 PCS
E UPPER SIDE RAILS 2 PCS
F SLAT SUPPORTS 3 PCS
G BACK GUARD RAIL 2 PCS
H FRONT GUARD RAIL 1 PC
I LADDER 1 PC
J TWIN PANELS 1 PC
K LEGS 8 PCS
L TRUNDLE (SOLD SEPARATELY) 1 PC
COMPONENT IDENTIFICATION AND HARDWARE
J
J
G
H
I
D
F
F
F
D
E
E
B
A
A
BC
L
K
K
K
K
K
K
K
K
DESCRIPTION
16 PCS
1
Threaded Rods
2
4
5
7
8
HEXAGONAL NUT
PHILLIPS WOOD SCREW 30MM
CURVED WASHER
OPEN WRENCH
6
STEEL DOWELS
METAL BRACKET
16PCS
16 PCS
26 PCS
26 PCS
4 PCS
1 PC
9
10
3
LOCK WASHER 16 PCS
PHILLIPS WOOD SCREW 25MM
PHILLIPS WOOD SCREW 20MM
WOODEN CAP 4 PCS
11

Page 4 of 10
FIGURE 02
FIGURE 01
STEP #1
LEG ASSEMBLY
STEP #1.1
Gently lay down the Lower End Panels (A) and
Upper End Panels (D) on a plain and non-abrasive
surface.
Note: On the bottom of both end panels are holes
(A,D) with pre-installed nuts that correspond to the
Threaded Rods pre-installed in the Legs (K).
STEP #1.2
Align and insert the Threaded Rods of the Legs (K)
into the holes and turn clockwise to tighten as
illustrated in FIGURE 01.
STEP #2
LOWER BUNK BED ASSEMBLY
STEP #2.1
Place the Lower End Panels (A, taller set) upright in
the position you wish the bed to be in when fully
assembled. The Lower End Panel's hardware should
be facing inwards. Secure the Threaded Rod (1) to
the Fixed Nut in both Lower End Panels (A) by
simply turning manually. Raise the Lower Side Rail
(B) up and place the Threaded Rod (1) to align with
the bore holes on the end of the Lower Side Rails
(B). Place the Lower Side Rails (B) up against the
End Panels (A) so the Threaded Rods (1) go
through the bore holes. Insert Curved Washer (2)
and Lock Washer (3), then engage Hex Nuts (4)
onto Threaded Rod (1) and tighten Hex nuts (4)
with Open Wrench (10), as illustrated in FIGURE
02.
STEP #2.2
Repeat the above procedure with the other Lower
Side Rail (B).
ASSEMBLY INSTRUCTIONS:
STEP #1. LEG ASSEMBLY
STEP #2. LOWER BUNK BED ASSEMBLY
STEP #3. INSTALLATION OF LOWER BUNK BED SLAT ROLL
STEP #4. UPPER BUNK BED ASSEMBLY
STEP #5. SLAT SUPPORT INSTALLATION TO UPPER SIDE RAILS
STEP #6. ATTACHMENT OF TWIN PANELS TO SLAT SUPPORTS AND UPPER SIDE RAILS
STEP #7. INSTALLATION OF FRONT AND BACK GUARD RAILS TO UPPER BUNK BED
STEP #8. BUNK BED ASSEMBLY
STEP #9. LADDER ASSEMBLY
STEP #10.METAL BRACKET INSTALLATION AND OPTIONAL TRUNDLE
STEP #11. ASSEMBLY OF BUNK AS TWO TWIN BEDS
IMPORTANT
These bed parts can be cumbersome and heavy to some people, therefore the assistance of two or more people is
recommended in order to prevent personal injury and ensure the bed parts are not damaged during the assembly
process.

Page 5 of 10
FIGURE 03
FIGURE 04
STEP #3.
INSTALLATION OF LOWER BUNK
BED SLAT ROLL
STEP #3.1
On the ends of the Slat Roll (C) are pre-bored
screw holes (5). Set the Slat Roll into the cleats of
the Lower Side Rails (B) and secure the Slat Roll
(C) with Phillips Screws (5) provided. Please see
FIGURE 03.
STEP #4.
UPPER BUNK BED ASSEMBLY
STEP #4.1
Place the Upper Bunk End Panels (D, shorter set)
in upright position. The Upper End Panel
hardware should be facing inwards. Secure the
Threaded Rod (1) to the Fixed Nut in both Upper
End Panels (D) by simply turning it manually.
Raise the Upper Side Rail (E) up and place the
Threaded Rod (1) to align with the bore holes on
the end of the Upper Side Rails (E). Place the
Upper Side Rails (E) up against the Upper End
Panels (D) so the Threaded Rods go through the
bore holes. Insert Curved Washer (2) and Lock
Washer (3), then engage Hex Nuts (4) on
Threaded Rods (1) and tighten Hex Nuts (4) with
Open Wrench (10), as illustrated in FIGURE 04.
STEP #4.2
Repeat the above procedure with the other Upper
Side Rail (E).

Page 6 of 10
FIGURE 05
FIGURE 06
STEP #5.
SLAT SUPPORT INSTALLATION TO UPPER SIDE RAILS
STEP #5.1
On the inside surface of the Upper Side Rails (E)
are cavities designed to hold the Slat Supports
(F). Attach the Slat Supports (F) to both Upper
Side Rails (E) and secure with Phillips Wood
Screws (6) provided. Please see FIGURE 05.
STEP #6.
ATTACHMENT OF TWIN PANELS TO SLAT SUPPORTS
AND UPPER SIDE RAILS
STEP #6.1
Lay the two Twin Panels (J) on top of assembled
upper bunk bed and secure these with Phillips
Wood Screws (6) provided as in FIGURE 06.

Page 7 of 10
FIGURE 07-A
FIGURE 07-B
STEP# 7.
INSTALLATION OF FRONT AND BACK GUARD
RAILS TO UPPER BUNK BED.
NOTE:
The Front Guard Rail can be installed at
either end of the bed depending on your
desired ladder location. Please see ladder
options in FIGURE 07-B.
STEP #7.1
On inside surface of both Front and Back
Guard Rails (G, H) are pre-installed metal
brackets, designed to attach to the Side
Rails (E) of the upper bunk. Install the
Front and the Back Guard Rails (G, H) on
the upper bunk by screwing (7) the Metal
Brackets into the Upper Side Rails (E).
(Refer FIGURE 07-A).

Page 8 of 10
FIGURE 09-A
STEP #8.
BUNK BED ASSEMBLY
STEP #8.1
On top surface of Lower End Panels (A) are
holes for Steel Dowels (9) that correspond
to the holes in the Legs of the Upper Bed (D).
Insert Steel Dowels (9) Into top of Lower End
Panels (A) as in FIGURE 08-A.
STEP #8.2
Gently lift up the upper bunk and align and
insert the Steel Dowels (9) into the holes in
the bottom of the Legs of upper bunk. Refer
to FIGURE 08-B.
STEP #9.
LADDER ASSEMBLY
STEP #9.1
On inside surface of the Ladder (I) are metal
brackets pre-installed with holes for the
Screws (7) to pass through. Hook the metal
brackets of the Ladder into the Upper Side
Rail (E) as well as the brackets on Lower
Side Rail (B); Once the Ladder (I) is set,
fasten the Ladder (I) with Phillips Wood
Screws (7) provided as in FIGURE 09-A and
FIGURE 09-B.
FIGURE 08
FIGURE 09-B

Page 9 of 10
GUARD
RAIL
[5"] MINIMUM DISTANCE
FROM TOP OF MATTRESS
TO TOP OF GUARDRAIL
9" MAXIMUM
THICKNESS
STEP # 10
METAL BRACKET INSTALLATION AND
OPTIONAL TRUNDLE
STEP # 10.1
After assembling the bunk bed, secure Guard Rails
(H & I) to Upper Side Rails (E) with Metal Brackets
(8) provided as in FIGURE 10.
UPPER BUNK MATTRESS DIAGRAM
BEDDING SPECIFICATIONS:
The following size mattress and foundation are
specified for use with this bunk bed.
MATTRESS : 37
1
2
" to 38
1
2
" W x 74" x to 75" L
maximum 9" H.
SLAT ROLL OR PLATFORM : 2
1
2
" H X 38
7
8
" W.
**Note: TOP MATTRESS AND PLATFORM MUST
NOT EXCEED 9
1
2
" TOTAL THICKNESS.
Be sure to adhere to these BEDDING
SPECIFICATIONS in order to avoid the possibility
of falling or entrapment. THESE SPECIFICATIONS
MUST BE STRICTLY ADHERED TO!
FIGURE 10
STEP # 10.2
After assembly, slide the optional Trundle
(sold separately) (L) underneath the bunk
bed as in FIGURE 11.
FIGURE 11

Page 10 of 10
Thank you for your purchase
www.rhbabyandchild.com
FIGURE 13
FIGURE 12
STEP #11.
ASSEMBLY OF BUNK AS TWO TWIN BEDS
STEP #11.1
Repeat Steps #1 - Step #5, Lower Bunk Assembly
and Upper Bunk Bed Assembly.
Note: In order to set up as two identical twin beds,
one Lower End Panel (A) may be removed and
exchanged with one Upper End Panel (D), so each
bed has a headboard (Lower End Panel-A) and
footboard (Upper End Panel-D). Please refer to
FIGURE 13.
STEP #11.2
Insert wooden caps on top of Lower End Panels
(A) as in figure 12.