baby&child FRENCH UPHOLSTERED WING CRIB User manual

Page 1 of 9
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief description of the part. Call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry
cloth. Blot spills immediately and wipe with a clean damp cloth. If the crib is to be stored, store in a cool dry place and
carefully package all original hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen Key (included)
NOTE: It may be easier to assemble product with two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 12- 34of a turn. After crib is
completely assembled, return to each bolt and tighten. Use wax or soap on all bolts to facilitate assembly
WARNING: Read all
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
Made in Vietnam
Distributed in the U.S.A. by:
Restoration Hardware Baby & Child
11640 Harrel St. Suite B
Mira Loma, CA 91752
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7
"FRENCH UPHOLSTERED WING CRIB"
All Restoration Hardware cribs are designed to meet the highest safety
standards and comply with all U.S. and Canadian cribs and cradles regulations.

Page 2 of 9
IMPORTANT SAFETY INFORMATION FOR CRIBS
WARNING: Infants can suffocate on soft bedding. Never add a pillow
or comforter. Never place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly
Instructions could result in serious injury or death.
•Never use plastic shipping bags or other plastic film as mattress covers because they can
cause suffocation.
•Infants can suffocate in gaps between crib sides and a mattress that is too small.
•To reduce the risk of SIDS, pediatricians recommend healthy infants to be placed on
their backs to sleep, unless otherwise approved by your physician.
Strangulation Hazard:
•Strings can cause strangulation! DO NOT place items with a string around a child’s neck,
such as hood strings or pacifier cords. DO NOT suspend strings over over a crib or
attach strings to toys.
•To help prevent strangulation tighten all fasteners. A child can trap parts of the body or
clothing on loose fasteners.
•DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
•When a child is able to pull to a standing position, set mattress to lowest position and
remove bumper pads, large toys and other objects that could serve as steps for climbing
out.
•When child is able to climb out or reaches the height of 35 in (89 cm), the crib shall no
longer be used, and the child should be placed in a youth or regular bed.
•Check this product for damaged hardware, loose joints, missing parts or sharp edges
before and after assembly and frequently during use. DO NOT use crib if any parts are
missing, damaged or broken. Contact customer service at 1-800-762-1751 for
replacement parts and instructional literature if needed. DO NOT substitute parts.
•DO NOT use a water mattress with this crib.
•If refinishing, use a non-toxic finish specified for children’s products.
•Follow warnings on all products in a crib.
•Never use plastic shopping bags or other plastic film as mattress covers because they
can cause suffocation.
•Infants can suffocate in gaps between crib sides and a mattress that is too small.

Page 3 of 9
IMPORTANT SAFETY INFORMATION FOR CRIBS
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4
INCHES BY 51-5/8 INCHES WITH A THICKNESS NOT EXCEEDING 6
INCHES.
WARNING
•Do not use this crib if the enclosed or attached instructions cannot be strictly
adhered to. Do not use this crib if the child is able to climb out unaided or is taller
than 90 cm. Do not place cords, straps or similar items that could become wound
around the child’s neck in or near this crib. Ensure that the sides are properly latched
or locked in place when the crib is occupied. The mattress used with this crib should
not be more than 15 cm thick and should be of such length and width that the gap
between the mattress and the sides of the crib is not more than 3 cm when the
mattress is pushed into the corner of the crib.
•Parents should inspect the crib regularly before putting the child in the crib each day
and confirm that every component of the crib is properly and securely in place.

Page 4 of 9
IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS
WARNING: ENTRAPMENT / STRANGULATION HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could result
in serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes may
strangle a child.
• The mattress intended for use on the bed shall be a full-size crib mattress
having minimum dimensions of 51-5/8 inches (1310mm) in length, 27-1/4
inches (690mm) in width and 4 inches (100 mm) in thickness, not
exceeding 6 inches (152 mm) in thickness.
• If guardrails are used as the mattress containment means, guardrail(s)
provided must be used to avoid the formation of a gap between the
mattress and the bed that could cause an entrapment.
•
DO NOT place bed near windows where cords from blinds or drapes may
strangle a child.
•
DO NOT place items with a string , cord, or ribbon around a child’s neck,
such as hood strings or pacifier cords.
•
DO NOT suspend strings over a toddler bed for any pacifier cords.
•
A child using the toddler or day bed shall be at least 15 months of age and
shall not weigh more than 50lbs (22.7kgs).

MATTRESS SUPPORT
ITEM IDENTIFICATION
For ease of identification, all parts are labeled to correspond to the step number in which
the part is used.
Step #1 Leg and End Panel assembly
End Panel and Stationary Side Rail assembly..................Page 6 of 9
Step #2 Mattress support arm assembly.
Stabilizer rail assembly
Mattress height adjustment ............................................... Page 7 of 9
Step #3 Installation of support slat into the End Panels.............. Page 8 of 9
Step #4 Toddler rail assembly............................................................ Page 9 of 9
Page 5 of 9

DETAIL A
DETAIL B
HARDWARE FOR STEP #1:
STEP #1
LEG AND END PANEL ASSEMBLY
STATIONARY SIDE RAIL AND END PANEL ASSEMBLY
STEP #1.1
Gently lay the End Panels on their backs on a clean and
non-abrasive surface.
STEP #1.2
Align and insert the Threaded Rod of the Legs into the holes
on the bottom of the End Panels and turn clockwise to tighten.
Please see DETAIL A.
STEP #1.3
Bring the End Panels and Stationary Side Panels into upright
position.
NOTE:
On inside lower faces of both End Panels are holes with
pre-installed nuts for the wooden dowels to pass through
which correspond with pre-installed wooden dowels on the
Stationary Side Rails.
STEP #1.4
Fasten the threaded rod through pre-installed nuts on both
End Panels. Bring the Stationary Side Rail up to the End Panel
and insert the Threaded Rods through the holes. Once
Stationary Side Rails are set, insert Curved Washers and
Lock Washers and fasten these with Hexagonal Nuts
provided. Please see DETAIL B.
STEP #1.5
Attach the upper part of both End Panels to the Stationary
Side Rails with Allen head bolts provided as in DETAIL B - 2.
NOTE: DO NOT OVER TIGHTEN
(A) 1/4"Ø X 1-11/16" BOLTS (x4 PIECES)
Page 6 of 9
(B) THREADED ROD (M8X100MM) (x8 PIECES)
OPEN WRENCH
14 X 90
CURVE WASHER LOCK WASHER HEXAGONAL NUTS

ALLEN WRENCH
MATTRESS NUT OPEN WRENCH
PLAIN WASHER
MATTRESS
BOLT
MATTRESS SUPPORT
STABILIZER RAIL
MATTRESS BOLT
C
D
STEP #2
MATTRESS SUPPORT ARM ASSEMBLY
STABILIZER RAIL ASSEMBLY
MATTRESS HEIGHT ADJUSTMENT
STEP #2.1
Lay mattress support flat with stabilizer rail on each side
NOTE:
On each end of the arm of the mattress support, there is a
hole for the bolt to pass through that corresponds to the
holes located in the frame of the mattress support.
STEP #2.2:
Insert the bolt into the desired hole of the frame through the
hole on the arm support. Fasten the bolt with Plain Washer,
Lock Washers & Hexagonal Nut provided. Repeat procedure
on other arms of the mattress support. Please see DETAIL C
WARNING:
Set the mattress support to the desired height by adjusting
the support arms. The mattress support should be at its
highest setting for newborns, then adjusted to the lower
positions as the child grows and becomes mobile. Once the
child is able to stand, the mattress support should be at its
lowest position.
STEP #2.3:
Install the stabilizer rail at ends of the arm support as
illustrated on DETAIL D.
ALLEN WRENCH
(D) 1/4" Ø X 1-3/8" MATTRESS BOLT (x8 PIECES)
(D) MATTRESS NUT (x8 PIECES)
(D) PLAIN WASHER (x8 PIECES)
(D) LOCK WASHER (x8 PIECES)
Page 7 of 9
HARDWARE FOR STEP #2:
11 X 70
OPEN WRENCH
DETAIL C
DETAIL D

STEP #3
INSTALLATION OF STABILIZER RAILS INTO
THE END PANELS
STEP #3.1
On inside face of both End Panels are
pre-installed metal brackets, designed to
hold the Stabilizer Rails. Set both ends of
the Stabilizer Rails into brackets as
illustrated in DETAIL E.
STEP #3.2
Once the Stabilizer Rails are set, gently tilt
the crib as illustrated in DETAIL F, then
fasten the stabilizer rails with Bolt together
with Plain Washer and Lock Washer
provided as illustrated in DETAIL G.
Page 8 of 9
(C) PLAIN WASHER (x4 PIECES)
(C) LOCK WASHER (x4 PIECES)
(C) BOLT 1/4" X 1/2" (x 4 PIECES)
HARDWARE FOR STEP #3:
DETAIL E
DETAIL F
DETAIL G

DD
DD
(DD) 1/4"Ø x 1/2 IN. BOLT (x4 PIECES)
ALLEN WRENCH
HARDWARE FOR STEP #4
Page 9 of 9
STEP #4
TODDLER RAIL ASSEMBLY
STEP #4.1:
Gently tilt the crib and release the bolts underneath
the metal brackets holding the Stabilizer Rails.
NOTE
• When converting to toddler bed, loosen all the bolts
and nuts that connect the End Panel and Stationary
Side Rail. Please see DETAIL H.
• If mattress support is not in the lowest position,
unscrew mattress support bolts and move to the
lowest position.
STEP #4.2
Repeat procedures from STEPS #1.3 - 1.4, substituting
one Stationary Side Rail with a Toddler Rail.
Please see DETAIL H.
NOTE:
Fill the top holes on both End Panels with bolts (E)
provided as in DETAIL I.
STEP #4.3
Repeat step #3. Installation of stabilizer rails into the
end rail panel as in detail (DETAIL J)
After assembly, re-tighten all bolts to a snug fit.
Thank you for your purchase
www.rhbabyandchild.com
DETAIL H
DETAIL J
DETAIL I