baby&child BELLINA DAYBED User manual

2
3
4
5
6
7
8
9
A
B
B
G
C
E
D
F
F
D
D
PHILLIPS WOOD SCREW 38 PCS
ALLEN HEAD BOLT
PLAIN WASHER
ALLEN WRENCH
4 PCS
4 PCS
1 PCS
NO.
1
HEX NUT
THREADED ROD
CURVED WASHER
LOCK WASHER
DESCRIPTION QTY.
4 PCS
4 PCS
8 PCS
4 PCS
WRENCH 1 PC
Customer Service - If you are missing parts or have any questions about this product please contact
us at 1-800-762-1751
TOOLS NEEDED
IMPORTANT
These bed parts can be cumbersome and heavy to some people; therefore the assistance of two or
more people is recommended in order to prevent personal injury and ensure the bed parts are not
damaged during the assembly process.
B E L L I N A D A Y B E D
PART LIST
A HEADBOARD
B END PANEL
CFRONT RAIL
D LEG
E TWIN PANEL SUPPORT
F TWIN PANEL
G TRUNDLE (OPTIONAL)
WARNING:
ADULT ASSEMBLY ONLY OWING TO THE PRESENCE OF SMALL PARTS, SHARP
POINTS AND EDGES.
-PHILLIPS HEAD SCREWDRIVER (NOT PROVIDED)
HARDWARE LIST
Page 1 of 3

Page 2 of 3
ASSEMBLY INSTRUCTIONS:
Thank you for choosing this quality product. Be sure to
check all packaging materials carefully for small parts
that may have become loose during shipment and place
all parts on a non-abrasive surface.
STEP #1:
Gently lay the Bellina Daybed Headboard (A) and End
Panels (B) on their backs on a flat and non-abrasive
surface.
Note: on the bottom of Headboard (A) and End Panels
(B) are holes with pre-installed nuts that correspond to
the threaded rods pre-installed in the Legs.
STEP #2:
Align and insert the threaded rod of the Legs (D) into
the holes and turn clockwise to tighten. Please see
sketch in FIGURE 01.
Note: Both ends of the Headboard (A) have holes for
the bolts to pass through and cavities that correspond
to the holes located on both connecting ends of the End
Panels (B) with insert nuts pre-installed.
STEP #3:
Place the Headboard (A) and the End Panels (B) upright
in the position you wish the bed to be in when fully
assembled.
STEP #4:
Insert Allen Head Bolt (6) in each hole together with
Plain Washer (7) and Lock Washer (3) and tighten with
Allen Wrench (8) provided. Please see FIGURE 02.
NOTE: DO NOT OVER TIGHTEN
STEP #5:
To install the Front Rail (C), fasten the Threaded Rod (1)
manually into the insert nut on both End Panels (B).
Insert the wooden dowels of the Front Rail (C) onto the
mating hole of both End Panels (B) as well as the
threaded rod of End Panels (B) into the mating holes of
the Front Rail (C). Insert Curved Washer (2), Lock
Washer (3) and engage Hexagonal Nut (4). Tighten all
the nuts with Wrench (5) provided. Please see FIGURE
03.
NOTE:
After assembly, re-tighten all bolts to a snug fit.
FIGURE 01
FIGURE 02
FIGURE 03

Thank you for your purchase
www.rhbabyandchild.com
Page 3 of 3
STEP #6.
On inside face of both Headboard (A) and Front
Rail (C) are cleats with cavity for the Twin Panel
Support (E). Set the Twin Panel Support in these
cleats and fasten both ends with Screws (9)
provided. Please see FIGURE 04.




STEP #7.
Set the Twin Panels (F) on assembled bed and
fasten these with Screws (9) provided as in
FIGURE 05.









STEP #8
After assembly, slide the optional Trundle (sold
separately) (G) underneath the Daybed as in
FIGURE 06.
FIGURE 04
FIGURE 05
FIGURE 06