baby&child Kenwood 101607 User manual

Canadian Bunk Bed regulations.
13
bunk beds are
All manuals and user guides at all-guides.com
all-guides.com

/GREY BUNK BED
All manuals and user guides at all-guides.com

1. Follow the information on the WARNINGS appearing o n the u pper bunk end structure and on the
carton. DO NOT REMOVE WARNING LABEL FROM BED.
2. Always use the specified size mattress or mattress support, or both to help prevent the likelihood of
entrapment or falls.
3. Surface of mattress must be at least 5 inches below the upper edge of guardrails on top bunk.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on upper bunk.
6. Periodically check and ensure that the guardrails, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the ladder for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact Restoration Hardware for replacement parts
10. Use of a night light may provide added safety precaution for a child using the upper bunk.
11. Use guardrails on both sides of the upper bunk.
12. If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and the wall.
13. The use of water flotation mattresses is prohibited.
14. STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are
not designed for use with the bed: for example, but not limited to, hooks, belts, and jump ropes.
15. Keep these instructions for future reference.
WARNING
TO HELP PREVENT SERIOUS
OR FATAL INJURIES FROM
ENTRAPMENT OR FALLS:
Never allow a child under 6 years
on upper bunk.
Use only mattress which is 74”-75”
long and 37 1 /2”-38 1/ 2” wide on
upper bunk.
Ensure thickness of mattress and
foundation combined does not
exceed 12” and mattress is at
least 5” below upper edge of
guardrails.
Use guardrails on both sides of
upper bunk.
Prohibit horseplay on or under
bed(s).
Prohibit more than one person on
upper bunk.
Use ladder for entering and
leaving upper bunk.
STRANGULATION HAZARD -
Never
attach or hang items to any part of the
bunk bed that are not designed for use
with the bed: for example, but not limited
to, hooks, belts, and jump ropes.
DO NOT REMOVE THIS LABEL
!
IMPORTANT SAFETY INFORMATION FOR BUNK BED
Page 3 of 13
All manuals and user guides at all-guides.com

Parts Identification
Page 4 of 13
All manuals and user guides at all-guides.com

I -Curved slotted washer 35x17
16 pieces
H -Thread rod 5/16''x88mm 16 pieces J - Wrench 5/16'' 1 piece
O - Slat roll screw #8x1 1/4" 8 pieces
N - Dowel pin 4'' long x4/5'' diameter
4 pieces
M - Ladder&Guardrail metal bracket
screw #8x3/4" 32 pieces
K - Guardrail oval metal plate
5 pieces
L - Guardrail L bracket& oval metal
plate screw #3x5/8" 13 pieces
P - Ladder bracket - 4 pieces
TOOLS NEEDED:
HARDWARE INCLUDED:
Philip Screwdriver(Not included)
Page 5 of 13
R - Metal bracket - 5 pieces
S- Guardrall L brackel - 3 pleces
All manuals and user guides at all-guides.com

Page 6 of 13
All manuals and user guides at all-guides.com
all-guides.com

Page 7 of 13
All manuals and user guides at all-guides.com

Page 8 of 13
STEP 3:Lower&Upper Bunk Assembly Instructions:
1.Install 4'' long x4/5'' diameter wooden dowels into top of the posts of the lower bunk
2.Carefully place the upper bed which already assembled on top of the lower bed
B
BB
C
C
D
A
A
C
C
D
N
N
N
All manuals and user guides at all-guides.com

Page 9 of 13
B
BB
CC
DD
AA
AA
CC
DD
F
M
L
K
Bottom of side rail
LL
EE
STEP 4:Guardrail Installation Instructions:
Section "C"
Secti n "o "C
Section "B"
Section "B"
Section "A"
Section "A"
Philip Screwdriver
Philip ScrewdriverPhilip Screwdriver
61 1/5'' Guardrail can be
placed at either end of bed
i f Front s de o Bunk bed
CC
1.Install 2 guardrails (E&F) as indicated below and in Section ''A''.The 61-1/5'' guard rail(F) can be
installed at either end of the bed that you desire.Attach guard rail (E&F) to be in position and fasten
metal bracket (R) short end two holes with 8x3/4" screws into pre-drill holes in the guard rail(E&F)
first,and then fasten the metal bracket long end two holes with 8x3/4" screws in the slat bearers on the
side rails (Refer to Section"A") .the metal bracket on the guard rails fit into slots in the slat bearers on
the side rails (C) (Refer to Section"A").Secure all brackets with #8x3/4" screws( M) that are provided.
2.Attach the L brackets (S) on the ends of the guardrails to posts of the upper bunk by using the
#3x5/8" screws(L) that are supplied with the guardrails and the screwdriver (Refer to
Section"B").Note:The L bracket (S)on the 61-1/5'' guardrail can be attached to either end
depending on which end of the bed you want your ladder to be.
3.Place and hold the oval metal plate(K)on the bottom of the guardrails for five positions and use
oval metal plate screws #3x5/8" (L)to secure guardrails and siderails together(Refer to Section
''C")
Metal bracket
short end
Metal bracket
long end
All manuals and user guides at all-guides.com

Page 10 of 13
All manuals and user guides at all-guides.com