Baccara G75-BWM User manual

Battery Installation
Replace the battery at the start of each irrigation
season and when the low battery symbol
appears. Use a 9V alkaline top quality battery only.
1. Using a Phillips
screwdriver, remove
the 4 battery cover screws.
2. Remove the battery
cover and seal.
3. Replace the battery.
4. After reattaching the seal, put
the cover back, and secure
with the 4 screws.
screws
seal
battery
cover
When replacing seal,
push seal tabs into slots.
Troubleshooting
PROBLEM CAUSE SOLUTION
Service Information
Baccara products are guaranteed to be free from
defects in material and workmanship for a period of
one year from the date of delivery.
This guarantee does not apply where equipment is
not used and installed strictly in accordance with
Baccara specifications and Users Guide. Neither
does it apply to failures cause by lightning strikes or
damage due to freezing temperatures or mechanical
causes (e.g. lawn mowers). Baccara is not liable for
indirect, incidental or consequential damage in
connection with the use of equipment.
To receive guarantee benefits, customers should
return defective units along with the receipt of
purchase to the nearest Baccara distributor.
Baccara reserves the right to alter, modify or redesign
its products, pricing and warranty at all times without
creating any liability for the obsolescence of customer
inventory of such parts or products.
This manufacturer guarantee policy may apply
differently in different countries.
FLOW CHART for G75 - BWM Controller
8
4257200301 (6/20)
G75 -BWM
Baccara Water Meter
Controller
Baccara Geva Ltd. Kvutzat Geva, 1891500, Israel
T. [phone] | F. [phone]
[email protected] | www.baccara-geva.com
10 11
The UD shows the water meter’s sensor
(volume per pulse).
100L: for 100 liter / pulse
1_M: for 1 cubic meter / pulse.
10M: for 10 cubic / pulse
100G: for 100 gallon / pulse
1MG: for 1000 gallon / pulse
Volume of water for irrigation
1. Two presses on MODE (Each press
2 secs). The below display appears:
The 2 right side digits blink (LD).
7
2. Use and to adjust the 2 right digits.
3. Press SET to continue.
4. Use and to adjust the 2 left digits.
5. Press SET to complete the water irrigation
volume and return to Auto Mode.
Irrigation Start Time & Days Select
1. Three presses on MODE (2 secs. each
press) the below display appears:
2. Use to change to “d1on”, or to
change to “d1oF” (day 1 off).
“oF”
blinks
3. Press SET to continue. If “oF” is selected,
the program continues to the next day.
If “on” is selected, the below display appears:
4. Use and to adjust the start’s minutes.
5. Press SET to continue.
6. Use and to adjust start’s hours.
7. Press SET to continue. UD shows “d2oF”, “oF”
blinks. Repeat steps 2 to 7 to program all days.
8. Press SET to complete the start time & days
select & return to Auto Mode. Users Guide
Maintenance
9
Faulty sensor Replace sensor
Controller in
Save energy mode
Press any key
to activate screen
Mode
Mode
Mode
Auto Mode Sleep - No display
2sec
Clock & Day
Min Hour
Mode
Water amount
Mode
Irrigation days
and start time
PROGRAMMING
2sec
2sec
Day select Hour
Min
Day deselect
Start Time
2 right digits 2 left digits
Day
Repeat 7 days
valve valve
®

Getting Started
Parts Identification
2
56
1
Description
The Baccara Water Meter Controller is an
Irrigation Controller that irrigates by volume
of water. Operates a G75 4Ω latch two wires
solenoid.
Display
The LCD display shows:
• Clock time
• Day No.
• Amount of water left during operation.
• Faucet icon displayed while operating.
• Low battery icon appears when battery
needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings when
power supply disconnected.
Controller display
Upper digits
UD
Lower digits
LD
G75
BWM
Controller
Green
Green
Black
Black
Black
Red
G75
Latch
4Ω
Water
Meter
Sensor
Wires connections
“Dryconn” #22 to #12 AWG
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• Off
• Manual
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows Week’s Day.
LD shows Clock.
Whilst in irrigation, the faucet icon will
turn on and the LD shows the amount of
water left to complete the irrigation.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) two minutes
after no button is pressed (shut off).
Display will turn on with pressing any
button.
• Off
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
Display will shut off as in Auto Mode.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• Manual
1. From Auto Mode press SET and
together, irrigation starts.
Display shows "Hand" and "Faucet"
icons.
LD shows the amount of water left
to complete the irrigation.
2. When irrigation is completed the
MODE returns to Auto.
3. To stop Manual press SET and
together, irrigation will stop and return
to Auto.
Programmable Setting : Time Adjust (Clock / Day)
Program setting can operate only from Auto
Mode. If during Program Mode no button
has been pressed within 2 minutes, the
Controller returns to Auto Mode.
Time Adjust (clock / day)
1. Press MODE for 2 seconds until the
below display appears:
2. Use and to adjust minutes.
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to continue.
Day 1 blinks
6. Below display appears:
7. Select the desired day by using
8. Press SET to complete time adjust
and return to Auto Mode.
&
134

Getting Started
Parts Identification
2
56
1
Description
The Baccara Water Meter Controller is an
Irrigation Controller that irrigates by volume
of water. Operates a G75 4Ω latch two wires
solenoid.
Display
The LCD display shows:
• Clock time
• Day No.
• Amount of water left during operation.
• Faucet icon displayed while operating.
• Low battery icon appears when battery
needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings when
power supply disconnected.
Controller display
Upper digits
UD
Lower digits
LD
G75
BWM
Controller
Green
Green
Black
Black
Black
Red
G75
Latch
4Ω
Water
Meter
Sensor
Wires connections
“Dryconn” #22 to #12 AWG
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• Off
• Manual
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows Week’s Day.
LD shows Clock.
Whilst in irrigation, the faucet icon will
turn on and the LD shows the amount of
water left to complete the irrigation.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) two minutes
after no button is pressed (shut off).
Display will turn on with pressing any
button.
• Off
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
Display will shut off as in Auto Mode.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• Manual
1. From Auto Mode press SET and
together, irrigation starts.
Display shows "Hand" and "Faucet"
icons.
LD shows the amount of water left
to complete the irrigation.
2. When irrigation is completed the
MODE returns to Auto.
3. To stop Manual press SET and
together, irrigation will stop and return
to Auto.
Programmable Setting : Time Adjust (Clock / Day)
Program setting can operate only from Auto
Mode. If during Program Mode no button
has been pressed within 2 minutes, the
Controller returns to Auto Mode.
Time Adjust (clock / day)
1. Press MODE for 2 seconds until the
below display appears:
2. Use and to adjust minutes.
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to continue.
Day 1 blinks
6. Below display appears:
7. Select the desired day by using
8. Press SET to complete time adjust
and return to Auto Mode.
&
134

Getting Started
Parts Identification
2
56
1
Description
The Baccara Water Meter Controller is an
Irrigation Controller that irrigates by volume
of water. Operates a G75 4Ω latch two wires
solenoid.
Display
The LCD display shows:
• Clock time
• Day No.
• Amount of water left during operation.
• Faucet icon displayed while operating.
• Low battery icon appears when battery
needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings when
power supply disconnected.
Controller display
Upper digits
UD
Lower digits
LD
G75
BWM
Controller
Green
Green
Black
Black
Black
Red
G75
Latch
4Ω
Water
Meter
Sensor
Wires connections
“Dryconn” #22 to #12 AWG
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• Off
• Manual
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows Week’s Day.
LD shows Clock.
Whilst in irrigation, the faucet icon will
turn on and the LD shows the amount of
water left to complete the irrigation.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) two minutes
after no button is pressed (shut off).
Display will turn on with pressing any
button.
• Off
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
Display will shut off as in Auto Mode.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• Manual
1. From Auto Mode press SET and
together, irrigation starts.
Display shows "Hand" and "Faucet"
icons.
LD shows the amount of water left
to complete the irrigation.
2. When irrigation is completed the
MODE returns to Auto.
3. To stop Manual press SET and
together, irrigation will stop and return
to Auto.
Programmable Setting : Time Adjust (Clock / Day)
Program setting can operate only from Auto
Mode. If during Program Mode no button
has been pressed within 2 minutes, the
Controller returns to Auto Mode.
Time Adjust (clock / day)
1. Press MODE for 2 seconds until the
below display appears:
2. Use and to adjust minutes.
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to continue.
Day 1 blinks
6. Below display appears:
7. Select the desired day by using
8. Press SET to complete time adjust
and return to Auto Mode.
&
134

Getting Started
Parts Identification
2
56
1
Description
The Baccara Water Meter Controller is an
Irrigation Controller that irrigates by volume
of water. Operates a G75 4Ω latch two wires
solenoid.
Display
The LCD display shows:
• Clock time
• Day No.
• Amount of water left during operation.
• Faucet icon displayed while operating.
• Low battery icon appears when battery
needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings when
power supply disconnected.
Controller display
Upper digits
UD
Lower digits
LD
G75
BWM
Controller
Green
Green
Black
Black
Black
Red
G75
Latch
4Ω
Water
Meter
Sensor
Wires connections
“Dryconn” #22 to #12 AWG
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• Off
• Manual
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows Week’s Day.
LD shows Clock.
Whilst in irrigation, the faucet icon will
turn on and the LD shows the amount of
water left to complete the irrigation.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) two minutes
after no button is pressed (shut off).
Display will turn on with pressing any
button.
• Off
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
Display will shut off as in Auto Mode.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• Manual
1. From Auto Mode press SET and
together, irrigation starts.
Display shows "Hand" and "Faucet"
icons.
LD shows the amount of water left
to complete the irrigation.
2. When irrigation is completed the
MODE returns to Auto.
3. To stop Manual press SET and
together, irrigation will stop and return
to Auto.
Programmable Setting : Time Adjust (Clock / Day)
Program setting can operate only from Auto
Mode. If during Program Mode no button
has been pressed within 2 minutes, the
Controller returns to Auto Mode.
Time Adjust (clock / day)
1. Press MODE for 2 seconds until the
below display appears:
2. Use and to adjust minutes.
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to continue.
Day 1 blinks
6. Below display appears:
7. Select the desired day by using
8. Press SET to complete time adjust
and return to Auto Mode.
&
134

Getting Started
Parts Identification
2
56
1
Description
The Baccara Water Meter Controller is an
Irrigation Controller that irrigates by volume
of water. Operates a G75 4Ω latch two wires
solenoid.
Display
The LCD display shows:
• Clock time
• Day No.
• Amount of water left during operation.
• Faucet icon displayed while operating.
• Low battery icon appears when battery
needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings when
power supply disconnected.
Controller display
Upper digits
UD
Lower digits
LD
G75
BWM
Controller
Green
Green
Black
Black
Black
Red
G75
Latch
4Ω
Water
Meter
Sensor
Wires connections
“Dryconn” #22 to #12 AWG
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• Off
• Manual
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows Week’s Day.
LD shows Clock.
Whilst in irrigation, the faucet icon will
turn on and the LD shows the amount of
water left to complete the irrigation.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) two minutes
after no button is pressed (shut off).
Display will turn on with pressing any
button.
• Off
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
Display will shut off as in Auto Mode.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• Manual
1. From Auto Mode press SET and
together, irrigation starts.
Display shows "Hand" and "Faucet"
icons.
LD shows the amount of water left
to complete the irrigation.
2. When irrigation is completed the
MODE returns to Auto.
3. To stop Manual press SET and
together, irrigation will stop and return
to Auto.
Programmable Setting : Time Adjust (Clock / Day)
Program setting can operate only from Auto
Mode. If during Program Mode no button
has been pressed within 2 minutes, the
Controller returns to Auto Mode.
Time Adjust (clock / day)
1. Press MODE for 2 seconds until the
below display appears:
2. Use and to adjust minutes.
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to continue.
Day 1 blinks
6. Below display appears:
7. Select the desired day by using
8. Press SET to complete time adjust
and return to Auto Mode.
&
134

Getting Started
Parts Identification
2
56
1
Description
The Baccara Water Meter Controller is an
Irrigation Controller that irrigates by volume
of water. Operates a G75 4Ω latch two wires
solenoid.
Display
The LCD display shows:
• Clock time
• Day No.
• Amount of water left during operation.
• Faucet icon displayed while operating.
• Low battery icon appears when battery
needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings when
power supply disconnected.
Controller display
Upper digits
UD
Lower digits
LD
G75
BWM
Controller
Green
Green
Black
Black
Black
Red
G75
Latch
4Ω
Water
Meter
Sensor
Wires connections
“Dryconn” #22 to #12 AWG
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• Off
• Manual
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows Week’s Day.
LD shows Clock.
Whilst in irrigation, the faucet icon will
turn on and the LD shows the amount of
water left to complete the irrigation.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) two minutes
after no button is pressed (shut off).
Display will turn on with pressing any
button.
• Off
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
Display will shut off as in Auto Mode.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• Manual
1. From Auto Mode press SET and
together, irrigation starts.
Display shows "Hand" and "Faucet"
icons.
LD shows the amount of water left
to complete the irrigation.
2. When irrigation is completed the
MODE returns to Auto.
3. To stop Manual press SET and
together, irrigation will stop and return
to Auto.
Programmable Setting : Time Adjust (Clock / Day)
Program setting can operate only from Auto
Mode. If during Program Mode no button
has been pressed within 2 minutes, the
Controller returns to Auto Mode.
Time Adjust (clock / day)
1. Press MODE for 2 seconds until the
below display appears:
2. Use and to adjust minutes.
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to continue.
Day 1 blinks
6. Below display appears:
7. Select the desired day by using
8. Press SET to complete time adjust
and return to Auto Mode.
&
134

Getting Started
Parts Identification
2
56
1
Description
The Baccara Water Meter Controller is an
Irrigation Controller that irrigates by volume
of water. Operates a G75 4Ω latch two wires
solenoid.
Display
The LCD display shows:
• Clock time
• Day No.
• Amount of water left during operation.
• Faucet icon displayed while operating.
• Low battery icon appears when battery
needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings when
power supply disconnected.
Controller display
Upper digits
UD
Lower digits
LD
G75
BWM
Controller
Green
Green
Black
Black
Black
Red
G75
Latch
4Ω
Water
Meter
Sensor
Wires connections
“Dryconn” #22 to #12 AWG
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• Off
• Manual
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows Week’s Day.
LD shows Clock.
Whilst in irrigation, the faucet icon will
turn on and the LD shows the amount of
water left to complete the irrigation.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) two minutes
after no button is pressed (shut off).
Display will turn on with pressing any
button.
• Off
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
Display will shut off as in Auto Mode.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• Manual
1. From Auto Mode press SET and
together, irrigation starts.
Display shows "Hand" and "Faucet"
icons.
LD shows the amount of water left
to complete the irrigation.
2. When irrigation is completed the
MODE returns to Auto.
3. To stop Manual press SET and
together, irrigation will stop and return
to Auto.
Programmable Setting : Time Adjust (Clock / Day)
Program setting can operate only from Auto
Mode. If during Program Mode no button
has been pressed within 2 minutes, the
Controller returns to Auto Mode.
Time Adjust (clock / day)
1. Press MODE for 2 seconds until the
below display appears:
2. Use and to adjust minutes.
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to continue.
Day 1 blinks
6. Below display appears:
7. Select the desired day by using
8. Press SET to complete time adjust
and return to Auto Mode.
&
134
Getting Started
Parts Identification
2
56
1
Description
The Baccara Water Meter Controller is an
Irrigation Controller that irrigates by volume
of water. Operates a G75 4Ω latch two wires
solenoid.
Display
The LCD display shows:
• Clock time
• Day No.
• Amount of water left during operation.
• Faucet icon displayed while operating.
• Low battery icon appears when battery
needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings when
power supply disconnected.
Controller display
Upper digits
UD
Lower digits
LD
G75
BWM
Controller
Green
Green
Black
Black
Black
Red
G75
Latch
4Ω
Water
Meter
Sensor
Wires connections
“Dryconn” #22 to #12 AWG
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• Off
• Manual
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows Week’s Day.
LD shows Clock.
Whilst in irrigation, the faucet icon will
turn on and the LD shows the amount of
water left to complete the irrigation.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) two minutes
after no button is pressed (shut off).
Display will turn on with pressing any
button.
• Off
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
Display will shut off as in Auto Mode.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• Manual
1. From Auto Mode press SET and
together, irrigation starts.
Display shows "Hand" and "Faucet"
icons.
LD shows the amount of water left
to complete the irrigation.
2. When irrigation is completed the
MODE returns to Auto.
3. To stop Manual press SET and
together, irrigation will stop and return
to Auto.
Programmable Setting : Time Adjust (Clock / Day)
Program setting can operate only from Auto
Mode. If during Program Mode no button
has been pressed within 2 minutes, the
Controller returns to Auto Mode.
Time Adjust (clock / day)
1. Press MODE for 2 seconds until the
below display appears:
2. Use and to adjust minutes.
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to continue.
Day 1 blinks
6. Below display appears:
7. Select the desired day by using
8. Press SET to complete time adjust
and return to Auto Mode.
&
134

Getting Started
Parts Identification
2
56
1
Description
The Baccara Water Meter Controller is an
Irrigation Controller that irrigates by volume
of water. Operates a G75 4Ω latch two wires
solenoid.
Display
The LCD display shows:
• Clock time
• Day No.
• Amount of water left during operation.
• Faucet icon displayed while operating.
• Low battery icon appears when battery
needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings when
power supply disconnected.
Controller display
Upper digits
UD
Lower digits
LD
G75
BWM
Controller
Green
Green
Black
Black
Black
Red
G75
Latch
4Ω
Water
Meter
Sensor
Wires connections
“Dryconn” #22 to #12 AWG
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• Off
• Manual
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows Week’s Day.
LD shows Clock.
Whilst in irrigation, the faucet icon will
turn on and the LD shows the amount of
water left to complete the irrigation.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) two minutes
after no button is pressed (shut off).
Display will turn on with pressing any
button.
• Off
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
Display will shut off as in Auto Mode.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• Manual
1. From Auto Mode press SET and
together, irrigation starts.
Display shows "Hand" and "Faucet"
icons.
LD shows the amount of water left
to complete the irrigation.
2. When irrigation is completed the
MODE returns to Auto.
3. To stop Manual press SET and
together, irrigation will stop and return
to Auto.
Programmable Setting : Time Adjust (Clock / Day)
Program setting can operate only from Auto
Mode. If during Program Mode no button
has been pressed within 2 minutes, the
Controller returns to Auto Mode.
Time Adjust (clock / day)
1. Press MODE for 2 seconds until the
below display appears:
2. Use and to adjust minutes.
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to continue.
Day 1 blinks
6. Below display appears:
7. Select the desired day by using
8. Press SET to complete time adjust
and return to Auto Mode.
&
134

Battery Installation
Replace the battery at the start of each irrigation
season and when the low battery symbol
appears. Use a 9V alkaline top quality battery only.
1. Using a Phillips
screwdriver, remove
the 4 battery cover screws.
2. Remove the battery
cover and seal.
3. Replace the battery.
4. After reattaching the seal, put
the cover back, and secure
with the 4 screws.
screws
seal
battery
cover
When replacing seal,
push seal tabs into slots.
Troubleshooting
PROBLEM CAUSE SOLUTION
Service Information
Baccara products are guaranteed to be free from
defects in material and workmanship for a period of
one year from the date of delivery.
This guarantee does not apply where equipment is
not used and installed strictly in accordance with
Baccara specifications and Users Guide. Neither
does it apply to failures cause by lightning strikes or
damage due to freezing temperatures or mechanical
causes (e.g. lawn mowers). Baccara is not liable for
indirect, incidental or consequential damage in
connection with the use of equipment.
To receive guarantee benefits, customers should
return defective units along with the receipt of
purchase to the nearest Baccara distributor.
Baccara reserves the right to alter, modify or redesign
its products, pricing and warranty at all times without
creating any liability for the obsolescence of customer
inventory of such parts or products.
This manufacturer guarantee policy may apply
differently in different countries.
FLOW CHART for G75 - BWM Controller
8
4257200301 (6/20)
G75 -BWM
Baccara Water Meter
Controller
Baccara Geva Ltd. Kvutzat Geva, 1891500, Israel
T. [phone] | F. [phone]
[email protected] | www.baccara-geva.com
10 11
The UD shows the water meter’s sensor
(volume per pulse).
100L: for 100 liter / pulse
1_M: for 1 cubic meter / pulse.
10M: for 10 cubic / pulse
100G: for 100 gallon / pulse
1MG: for 1000 gallon / pulse
Volume of water for irrigation
1. Two presses on MODE (Each press
2 secs). The below display appears:
The 2 right side digits blink (LD).
7
2. Use and to adjust the 2 right digits.
3. Press SET to continue.
4. Use and to adjust the 2 left digits.
5. Press SET to complete the water irrigation
volume and return to Auto Mode.
Irrigation Start Time & Days Select
1. Three presses on MODE (2 secs. each
press) the below display appears:
2. Use to change to “d1on”, or to
change to “d1oF” (day 1 off).
“oF”
blinks
3. Press SET to continue. If “oF” is selected,
the program continues to the next day.
If “on” is selected, the below display appears:
4. Use and to adjust the start’s minutes.
5. Press SET to continue.
6. Use and to adjust start’s hours.
7. Press SET to continue. UD shows “d2oF”, “oF”
blinks. Repeat steps 2 to 7 to program all days.
8. Press SET to complete the start time & days
select & return to Auto Mode. Users Guide
Maintenance
9
Faulty sensor Replace sensor
Controller in
Save energy mode
Press any key
to activate screen
Mode
Mode
Mode
Auto Mode Sleep - No display
2sec
Clock & Day
Min Hour
Mode
Water amount
Mode
Irrigation days
and start time
PROGRAMMING
2sec
2sec
Day select Hour
Min
Day deselect
Start Time
2 right digits 2 left digits
Day
Repeat 7 days
valve valve
®

Battery Installation
Replace the battery at the start of each irrigation
season and when the low battery symbol
appears. Use a 9V alkaline top quality battery only.
1. Using a Phillips
screwdriver, remove
the 4 battery cover screws.
2. Remove the battery
cover and seal.
3. Replace the battery.
4. After reattaching the seal, put
the cover back, and secure
with the 4 screws.
screws
seal
battery
cover
When replacing seal,
push seal tabs into slots.
Troubleshooting
PROBLEM CAUSE SOLUTION
Service Information
Baccara products are guaranteed to be free from
defects in material and workmanship for a period of
one year from the date of delivery.
This guarantee does not apply where equipment is
not used and installed strictly in accordance with
Baccara specifications and Users Guide. Neither
does it apply to failures cause by lightning strikes or
damage due to freezing temperatures or mechanical
causes (e.g. lawn mowers). Baccara is not liable for
indirect, incidental or consequential damage in
connection with the use of equipment.
To receive guarantee benefits, customers should
return defective units along with the receipt of
purchase to the nearest Baccara distributor.
Baccara reserves the right to alter, modify or redesign
its products, pricing and warranty at all times without
creating any liability for the obsolescence of customer
inventory of such parts or products.
This manufacturer guarantee policy may apply
differently in different countries.
FLOW CHART for G75 - BWM Controller
8
4257200301 (6/20)
G75 -BWM
Baccara Water Meter
Controller
Baccara Geva Ltd. Kvutzat Geva, 1891500, Israel
T. [phone] | F. [phone]
[email protected] | www.baccara-geva.com
10 11
The UD shows the water meter’s sensor
(volume per pulse).
100L: for 100 liter / pulse
1_M: for 1 cubic meter / pulse.
10M: for 10 cubic / pulse
100G: for 100 gallon / pulse
1MG: for 1000 gallon / pulse
Volume of water for irrigation
1. Two presses on MODE (Each press
2 secs). The below display appears:
The 2 right side digits blink (LD).
7
2. Use and to adjust the 2 right digits.
3. Press SET to continue.
4. Use and to adjust the 2 left digits.
5. Press SET to complete the water irrigation
volume and return to Auto Mode.
Irrigation Start Time & Days Select
1. Three presses on MODE (2 secs. each
press) the below display appears:
2. Use to change to “d1on”, or to
change to “d1oF” (day 1 off).
“oF”
blinks
3. Press SET to continue. If “oF” is selected,
the program continues to the next day.
If “on” is selected, the below display appears:
4. Use and to adjust the start’s minutes.
5. Press SET to continue.
6. Use and to adjust start’s hours.
7. Press SET to continue. UD shows “d2oF”, “oF”
blinks. Repeat steps 2 to 7 to program all days.
8. Press SET to complete the start time & days
select & return to Auto Mode. Users Guide
Maintenance
9
Faulty sensor Replace sensor
Controller in
Save energy mode
Press any key
to activate screen
Mode
Mode
Mode
Auto Mode Sleep - No display
2sec
Clock & Day
Min Hour
Mode
Water amount
Mode
Irrigation days
and start time
PROGRAMMING
2sec
2sec
Day select Hour
Min
Day deselect
Start Time
2 right digits 2 left digits
Day
Repeat 7 days
valve valve
®

Battery Installation
Replace the battery at the start of each irrigation
season and when the low battery symbol
appears. Use a 9V alkaline top quality battery only.
1. Using a Phillips
screwdriver, remove
the 4 battery cover screws.
2. Remove the battery
cover and seal.
3. Replace the battery.
4. After reattaching the seal, put
the cover back, and secure
with the 4 screws.
screws
seal
battery
cover
When replacing seal,
push seal tabs into slots.
Troubleshooting
PROBLEM CAUSE SOLUTION
Service Information
Baccara products are guaranteed to be free from
defects in material and workmanship for a period of
one year from the date of delivery.
This guarantee does not apply where equipment is
not used and installed strictly in accordance with
Baccara specifications and Users Guide. Neither
does it apply to failures cause by lightning strikes or
damage due to freezing temperatures or mechanical
causes (e.g. lawn mowers). Baccara is not liable for
indirect, incidental or consequential damage in
connection with the use of equipment.
To receive guarantee benefits, customers should
return defective units along with the receipt of
purchase to the nearest Baccara distributor.
Baccara reserves the right to alter, modify or redesign
its products, pricing and warranty at all times without
creating any liability for the obsolescence of customer
inventory of such parts or products.
This manufacturer guarantee policy may apply
differently in different countries.
FLOW CHART for G75 - BWM Controller
8
4257200301 (6/20)
G75 -BWM
Baccara Water Meter
Controller
Baccara Geva Ltd. Kvutzat Geva, 1891500, Israel
T. [phone] | F. [phone]
[email protected] | www.baccara-geva.com
10 11
The UD shows the water meter’s sensor
(volume per pulse).
100L: for 100 liter / pulse
1_M: for 1 cubic meter / pulse.
10M: for 10 cubic / pulse
100G: for 100 gallon / pulse
1MG: for 1000 gallon / pulse
Volume of water for irrigation
1. Two presses on MODE (Each press
2 secs). The below display appears:
The 2 right side digits blink (LD).
7
2. Use and to adjust the 2 right digits.
3. Press SET to continue.
4. Use and to adjust the 2 left digits.
5. Press SET to complete the water irrigation
volume and return to Auto Mode.
Irrigation Start Time & Days Select
1. Three presses on MODE (2 secs. each
press) the below display appears:
2. Use to change to “d1on”, or to
change to “d1oF” (day 1 off).
“oF”
blinks
3. Press SET to continue. If “oF” is selected,
the program continues to the next day.
If “on” is selected, the below display appears:
4. Use and to adjust the start’s minutes.
5. Press SET to continue.
6. Use and to adjust start’s hours.
7. Press SET to continue. UD shows “d2oF”, “oF”
blinks. Repeat steps 2 to 7 to program all days.
8. Press SET to complete the start time & days
select & return to Auto Mode. Users Guide
Maintenance
9
Faulty sensor Replace sensor
Controller in
Save energy mode
Press any key
to activate screen
Mode
Mode
Mode
Auto Mode Sleep - No display
2sec
Clock & Day
Min Hour
Mode
Water amount
Mode
Irrigation days
and start time
PROGRAMMING
2sec
2sec
Day select Hour
Min
Day deselect
Start Time
2 right digits 2 left digits
Day
Repeat 7 days
valve valve
®

Battery Installation
Replace the battery at the start of each irrigation
season and when the low battery symbol
appears. Use a 9V alkaline top quality battery only.
1. Using a Phillips
screwdriver, remove
the 4 battery cover screws.
2. Remove the battery
cover and seal.
3. Replace the battery.
4. After reattaching the seal, put
the cover back, and secure
with the 4 screws.
screws
seal
battery
cover
When replacing seal,
push seal tabs into slots.
Troubleshooting
PROBLEM CAUSE SOLUTION
Service Information
Baccara products are guaranteed to be free from
defects in material and workmanship for a period of
one year from the date of delivery.
This guarantee does not apply where equipment is
not used and installed strictly in accordance with
Baccara specifications and Users Guide. Neither
does it apply to failures cause by lightning strikes or
damage due to freezing temperatures or mechanical
causes (e.g. lawn mowers). Baccara is not liable for
indirect, incidental or consequential damage in
connection with the use of equipment.
To receive guarantee benefits, customers should
return defective units along with the receipt of
purchase to the nearest Baccara distributor.
Baccara reserves the right to alter, modify or redesign
its products, pricing and warranty at all times without
creating any liability for the obsolescence of customer
inventory of such parts or products.
This manufacturer guarantee policy may apply
differently in different countries.
FLOW CHART for G75 - BWM Controller
8
4257200301 (6/20)
G75 -BWM
Baccara Water Meter
Controller
Baccara Geva Ltd. Kvutzat Geva, 1891500, Israel
T. [phone] | F. [phone]
[email protected] | www.baccara-geva.com
10 11
The UD shows the water meter’s sensor
(volume per pulse).
100L: for 100 liter / pulse
1_M: for 1 cubic meter / pulse.
10M: for 10 cubic / pulse
100G: for 100 gallon / pulse
1MG: for 1000 gallon / pulse
Volume of water for irrigation
1. Two presses on MODE (Each press
2 secs). The below display appears:
The 2 right side digits blink (LD).
7
2. Use and to adjust the 2 right digits.
3. Press SET to continue.
4. Use and to adjust the 2 left digits.
5. Press SET to complete the water irrigation
volume and return to Auto Mode.
Irrigation Start Time & Days Select
1. Three presses on MODE (2 secs. each
press) the below display appears:
2. Use to change to “d1on”, or to
change to “d1oF” (day 1 off).
“oF”
blinks
3. Press SET to continue. If “oF” is selected,
the program continues to the next day.
If “on” is selected, the below display appears:
4. Use and to adjust the start’s minutes.
5. Press SET to continue.
6. Use and to adjust start’s hours.
7. Press SET to continue. UD shows “d2oF”, “oF”
blinks. Repeat steps 2 to 7 to program all days.
8. Press SET to complete the start time & days
select & return to Auto Mode. Users Guide
Maintenance
9
Faulty sensor Replace sensor
Controller in
Save energy mode
Press any key
to activate screen
Mode
Mode
Mode
Auto Mode Sleep - No display
2sec
Clock & Day
Min Hour
Mode
Water amount
Mode
Irrigation days
and start time
PROGRAMMING
2sec
2sec
Day select Hour
Min
Day deselect
Start Time
2 right digits 2 left digits
Day
Repeat 7 days
valve valve
®

Battery Installation
Replace the battery at the start of each irrigation
season and when the low battery symbol
appears. Use a 9V alkaline top quality battery only.
1. Using a Phillips
screwdriver, remove
the 4 battery cover screws.
2. Remove the battery
cover and seal.
3. Replace the battery.
4. After reattaching the seal, put
the cover back, and secure
with the 4 screws.
screws
seal
battery
cover
When replacing seal,
push seal tabs into slots.
Troubleshooting
PROBLEM CAUSE SOLUTION
Service Information
Baccara products are guaranteed to be free from
defects in material and workmanship for a period of
one year from the date of delivery.
This guarantee does not apply where equipment is
not used and installed strictly in accordance with
Baccara specifications and Users Guide. Neither
does it apply to failures cause by lightning strikes or
damage due to freezing temperatures or mechanical
causes (e.g. lawn mowers). Baccara is not liable for
indirect, incidental or consequential damage in
connection with the use of equipment.
To receive guarantee benefits, customers should
return defective units along with the receipt of
purchase to the nearest Baccara distributor.
Baccara reserves the right to alter, modify or redesign
its products, pricing and warranty at all times without
creating any liability for the obsolescence of customer
inventory of such parts or products.
This manufacturer guarantee policy may apply
differently in different countries.
FLOW CHART for G75 - BWM Controller
8
4257200301 (6/20)
G75 -BWM
Baccara Water Meter
Controller
Baccara Geva Ltd. Kvutzat Geva, 1891500, Israel
T. [phone] | F. [phone]
[email protected] | www.baccara-geva.com
10 11
The UD shows the water meter’s sensor
(volume per pulse).
100L: for 100 liter / pulse
1_M: for 1 cubic meter / pulse.
10M: for 10 cubic / pulse
100G: for 100 gallon / pulse
1MG: for 1000 gallon / pulse
Volume of water for irrigation
1. Two presses on MODE (Each press
2 secs). The below display appears:
The 2 right side digits blink (LD).
7
2. Use and to adjust the 2 right digits.
3. Press SET to continue.
4. Use and to adjust the 2 left digits.
5. Press SET to complete the water irrigation
volume and return to Auto Mode.
Irrigation Start Time & Days Select
1. Three presses on MODE (2 secs. each
press) the below display appears:
2. Use to change to “d1on”, or to
change to “d1oF” (day 1 off).
“oF”
blinks
3. Press SET to continue. If “oF” is selected,
the program continues to the next day.
If “on” is selected, the below display appears:
4. Use and to adjust the start’s minutes.
5. Press SET to continue.
6. Use and to adjust start’s hours.
7. Press SET to continue. UD shows “d2oF”, “oF”
blinks. Repeat steps 2 to 7 to program all days.
8. Press SET to complete the start time & days
select & return to Auto Mode. Users Guide
Maintenance
9
Faulty sensor Replace sensor
Controller in
Save energy mode
Press any key
to activate screen
Mode
Mode
Mode
Auto Mode Sleep - No display
2sec
Clock & Day
Min Hour
Mode
Water amount
Mode
Irrigation days
and start time
PROGRAMMING
2sec
2sec
Day select Hour
Min
Day deselect
Start Time
2 right digits 2 left digits
Day
Repeat 7 days
valve valve
®

Battery Installation Replace the battery at the start of each irrigation season and when the low battery symbol appears. Use a 9V alkaline top quality battery only.
1. Using a Phillips screwdriver, remove the 4 battery cover screws. 2. Remove the battery cover and seal. 3. Replace the battery. 4. After reattaching the seal, put the cover back, and secure with the 4 screws.
screws
seal
battery cover
When replacing seal, push seal tabs into slots.
Troubleshooting
PROBLEM CAUSE SOLUTION
Service Information
Baccara products are guaranteed to be free from defects in material and workmanship for a period of one year from the date of delivery. This guarantee does not apply where equipment is not used and installed strictly in accordance with Baccara specifications and Users Guide. Neither does it apply to failures cause by lightning strikes or damage due to freezing temperatures or mechanical causes (e.g. lawn mowers). Baccara is not liable for indirect, incidental or consequential damage in connection with the use of equipment. To receive guarantee benefits, customers should return defective units along with the receipt of purchase to the nearest Baccara distributor. Baccara reserves the right to alter, modify or redesign its products, pricing and warranty at all times without creating any liability for the obsolescence of customer inventory of such parts or products. This manufacturer guarantee policy may apply differently in different countries.
FLOW CHART for G75 - BWM Controller
8
4257200301 (6/20)
G75 -BWM
Baccara Water Meter
Controller
Baccara Geva Ltd. Kvutzat Geva, 1891500, Israel
T. [phone] | F. [phone]
[email protected] | www.baccara-geva.com
10 11
The UD shows the water meter’s sensor
(volume per pulse).
100L: for 100 liter / pulse 1_M: for 1 cubic meter / pulse. 10M: for 10 cubic / pulse 100G: for 100 gallon / pulse 1MG: for 1000 gallon / pulse
Volume of water for irrigation
1. Two presses on MODE (Each press 2 secs). The below display appears:
The 2 right side digits blink (LD).
7
2. Use and to adjust the 2 right digits.
3. Press SET to continue.
4. Use and to adjust the 2 left digits.
5. Press SET to complete the water irrigation
volume and return to Auto Mode.
Irrigation Start Time & Days Select
1. Three presses on MODE (2 secs. each
press) the below display appears:
2. Use to change to “d1on”, or to change to “d1oF” (day 1 off).
“oF” blinks
3. Press SET to continue. If “oF” is selected, the program continues to the next day. If “on” is selected, the below display appears:
4. Use and to adjust the start’s minutes.
5. Press SET to continue. 6. Use and to adjust start’s hours. 7. Press SET to continue. UD shows “d2oF”, “oF” blinks. Repeat steps 2 to 7 to program all days. 8. Press SET to complete the start time & days select & return to Auto Mode. Users Guide
Maintenance
9
Faulty sensor Replace sensor
Controller in Save energy mode
Press any key to activate screen
Mode
Mode
Mode
Auto Mode Sleep - No display
2sec
Clock & Day
Min Hour
Mode
Water amount
Mode
Irrigation days
and start time
PROGRAMMING
2sec
2sec
Day select Hour
Min
Day deselect
Start Time
2 right digits 2 left digits
Day
Repeat 7 days
valve valve
®