Baccara G75-DFC User manual

Battery Installation
Replace the battery at the start of each
irrigation season and when the low battery
symbol appears.
Use a 9V alkaline top quality battery only.
1. Using a Phillips screw driver, remove the
four battery cover screws.
2. Remove the battery cover and seal.
3. Replace the battery.
4. After reattaching the seal, put the cover
back, and secure with the four screws.
G75 - DFC
Dierential Filtration
Controller
4257170101 (6/20)
• English
10 Maintenance
screws
Battery cover seal
When replacing the seal, push seal tabs
into slots.
11 12 Troubleshooting
No water
Battery dead
O Mode
Valve # select
is incorrect
Shut O
Sleep
Battery dead
Open water
Replace battery
Set Auto Mode
#Correct valve select
Press any button
Press MODE
Replace battery
No FC
occurance
Valve does
not work
Blank
display
Problem Cause Solution
Guarantee
Baccara products are guaranteed to be free from
defects in material and workmanship for a period
of one year from the date of delivery.
This guarantee does nor apply where equipment is
not used and installed strictly in accordance with
Baccara specifications and Users Guide. Neither
does it apply to failures caused by lightning strikes
or damage due to freezing temperatures or mecha-
nical causes (e.g. lawn mowers).
Baccara is not
To receive guarantee benefits, customers should
return defective units along with the receipt to the
nearest Baccara distributor.
Baccara reserves the right to alter, modify or
redesign its products, pricing and guarantee at all
times without creating any liability for the
obsolescence of customer inventory of such parts
or products.
This manufacturer guarantee policy may apply
differently in different countries.
liable for indirect, incidental or consequential
damage in connection with the use of equipment.
13
Flow Chart for G75 -DFC Dierential Filtration Controller
Users Guide
Mode
1 sec
Mode
Mode
Auto Mode No display
>2sec
Set valves
on time
Sec Min
Mode
Interval time
between
FC
if Min = A
select
Mode
Valves select
deselect
PROGRAMMING
3 valves
Min Hrs
®

Getting Started
1
Parts Identification
1
12
Wires connections - DC
456
8
“Dryconn” #22 to #12 AWG
9
Programmable Setting
Default: Valve #1 (Max. three valves)
You have a choice of which # valve will be
operated by the controller.
In case of output #1 burnout, you can
connect the valve to output #2 and select
valve #2 to operate or #3.
1. To select the valve #. Press MODE (one
long press, then two short presses.
This display appears:
2. Use to select valve #1. Valve #1 remains,
valve #2 blinks. Or use to deselect
valve #1. Valve #1 disappears,
valve #2 blinks.
3. Repeat the above for valves 2 and 3.
Description
The Baccara Dierential Filtration Controller
combines a Controller and Dierential
Pressure Sensor (DP).
Molded DP with three wires cable. Controller
with seven wires for valves and sensor
interface.
The DFC controller is oered as DC Latch
only, and it is suitable for Baccara solenoid
Latch 4 ohm.
The controllers operates up to three
solenoids. The Controller shows the actual
DIF pressure and the pressure SET point.
The Flushing Cycle (FC) begins when
DIF≥SET appears.
Display
The LCD display shows:
• Actual DIF pressure
• SET point pressure
• FC counter
• Faucet icon displayed whilst FC operating
• Low battery icon appears when
battery needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
• Max. High pressure 14bar/200psi
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings
when power supply disconnected.
Mounting
DP: 2"/ 52mm diameter
2 ft/ 60 cm. 3 wires cable
High and low pressure ports 1/ 8”
BSP/NPT male
High pressure port marked on housing.
Important: Connect High pressure before
Low pressure. Disconnect Low pressure
before High pressure.
Electric cable Pipe fitting
Mounting
screws x 2
Pipe fitting
Controller (DFC display)
Upper digits
UD
Lower digits
LD
DP
White Black
Yellow
Blue
Green
G75
DFC
Black
Black
Red
Orange
Black
Red
Orange
Black
Di.
Sensor
3
1. Strip wires ¾" and group
bare wires ends together.
No pre-twisting
necessary with solid wire.
Pre-twist stranded wire. If
using both wire types,
wrap stranded wire
around solid wires.
See 1A.
2. Insert wires through
flexible sealing fingers
and bend wires wires into
either <V- Channel>.
3. Push inner sleeve into
pre-filled outer sleeve
until double-locked.
Pre-filled silicone fuller
waterproofs the
connection. Do not reuse
connector.
LV9000 - Wire connectors
Installation instructions
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires
with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• O
• FC counter rest
• Manual FC
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows counter value (see section 3).
LD shows DIF and SET values.
Whilst in FC, the faucet icon will turn on
and the operating valve number will blink.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) one minute
after no button is pressed (shut o).
Display will turn on with pressing any
button.
If DIF≥SET for (n) consecutive measuring
samples, FC starts. FC ends one min.
after the last valve shut down.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• FC Counter reset
1. From Auto Mode press MODE and
together UD will blink with
counter content.
2. For RESET, press MODE and
together, UD shows c000, then back
to Auto.
3. If RESET is not needed, press SET,
then back to Auto.
• Manual FC
1. From Auto Mode press SET and
together, FC starts.
Display shows "Hand" and "Faucet"
icons. VALVE and operating valve #
blink.
2. When FC is completed the MODE
returns to Auto.
3. To stop Manual FC press SET and
together, FC will stop and return to
Auto.
Factory Setting
These settings cannot be programmed by
the user:
• Pressure units: bar
• FC delay: 2 consecutive readings of
DIF≥SET before FC starts.
• Sample Interval time: Auto, as the
DIF becomes closer to the SET
point, the interval time between
samples shortens.
Max. Interval 60 secs./ Min.
Interval 5 sec.
• O time between valves during FC:
20 sec.
• Consecutive FC count number for
alarm: 5 count
• Sensor calibration.
Factory Setting
7
Valve on Time: default: 40 sec. range
(5 min. 59 sec.) Same time for all valves.
1. To set Valve on Time press MODE until
below display appears:
2. Use and to adjust seconds.
3. Press SET to continue.
4. Use and to adjust minutes.
5. Press SET to complete setting.
This interval value will be the max. time
between two consecutive FC if DIF
pressure does not execute FC.
Range (23 hrs: 59 min. A)
If Ais selected, this setting is ignored.
1. To set Interval Time between FC
press MODE (one long press), then
one short press. The below display
appears:
Default: A
Interval time between FC
Programmable Setting
Select Valve no.
2. Use and to adjust minutes.
(If A is selected, press SET to complete
this setting).
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to complete this setting.
• O
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
No pressure measuring process occurs
Display will shut o as in Auto Mode.

Getting Started
1
Parts Identification
1
12
Wires connections - DC
456
8
“Dryconn” #22 to #12 AWG
9
Programmable Setting
Default: Valve #1 (Max. three valves)
You have a choice of which # valve will be
operated by the controller.
In case of output #1 burnout, you can
connect the valve to output #2 and select
valve #2 to operate or #3.
1. To select the valve #. Press MODE (one
long press, then two short presses.
This display appears:
2. Use to select valve #1. Valve #1 remains,
valve #2 blinks. Or use to deselect
valve #1. Valve #1 disappears,
valve #2 blinks.
3. Repeat the above for valves 2 and 3.
Description
The Baccara Dierential Filtration Controller
combines a Controller and Dierential
Pressure Sensor (DP).
Molded DP with three wires cable. Controller
with seven wires for valves and sensor
interface.
The DFC controller is oered as DC Latch
only, and it is suitable for Baccara solenoid
Latch 4 ohm.
The controllers operates up to three
solenoids. The Controller shows the actual
DIF pressure and the pressure SET point.
The Flushing Cycle (FC) begins when
DIF≥SET appears.
Display
The LCD display shows:
• Actual DIF pressure
• SET point pressure
• FC counter
• Faucet icon displayed whilst FC operating
• Low battery icon appears when
battery needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
• Max. High pressure 14bar/200psi
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings
when power supply disconnected.
Mounting
DP: 2"/ 52mm diameter
2 ft/ 60 cm. 3 wires cable
High and low pressure ports 1/ 8”
BSP/NPT male
High pressure port marked on housing.
Important: Connect High pressure before
Low pressure. Disconnect Low pressure
before High pressure.
Electric cable Pipe fitting
Mounting
screws x 2
Pipe fitting
Controller (DFC display)
Upper digits
UD
Lower digits
LD
DP
White Black
Yellow
Blue
Green
G75
DFC
Black
Black
Red
Orange
Black
Red
Orange
Black
Di.
Sensor
3
1. Strip wires ¾" and group
bare wires ends together.
No pre-twisting
necessary with solid wire.
Pre-twist stranded wire. If
using both wire types,
wrap stranded wire
around solid wires.
See 1A.
2. Insert wires through
flexible sealing fingers
and bend wires wires into
either <V- Channel>.
3. Push inner sleeve into
pre-filled outer sleeve
until double-locked.
Pre-filled silicone fuller
waterproofs the
connection. Do not reuse
connector.
LV9000 - Wire connectors
Installation instructions
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires
with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• O
• FC counter rest
• Manual FC
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows counter value (see section 3).
LD shows DIF and SET values.
Whilst in FC, the faucet icon will turn on
and the operating valve number will blink.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) one minute
after no button is pressed (shut o).
Display will turn on with pressing any
button.
If DIF≥SET for (n) consecutive measuring
samples, FC starts. FC ends one min.
after the last valve shut down.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• FC Counter reset
1. From Auto Mode press MODE and
together UD will blink with
counter content.
2. For RESET, press MODE and
together, UD shows c000, then back
to Auto.
3. If RESET is not needed, press SET,
then back to Auto.
• Manual FC
1. From Auto Mode press SET and
together, FC starts.
Display shows "Hand" and "Faucet"
icons. VALVE and operating valve #
blink.
2. When FC is completed the MODE
returns to Auto.
3. To stop Manual FC press SET and
together, FC will stop and return to
Auto.
Factory Setting
These settings cannot be programmed by
the user:
• Pressure units: bar
• FC delay: 2 consecutive readings of
DIF≥SET before FC starts.
• Sample Interval time: Auto, as the
DIF becomes closer to the SET
point, the interval time between
samples shortens.
Max. Interval 60 secs./ Min.
Interval 5 sec.
• O time between valves during FC:
20 sec.
• Consecutive FC count number for
alarm: 5 count
• Sensor calibration.
Factory Setting
7
Valve on Time: default: 40 sec. range
(5 min. 59 sec.) Same time for all valves.
1. To set Valve on Time press MODE until
below display appears:
2. Use and to adjust seconds.
3. Press SET to continue.
4. Use and to adjust minutes.
5. Press SET to complete setting.
This interval value will be the max. time
between two consecutive FC if DIF
pressure does not execute FC.
Range (23 hrs: 59 min. A)
If Ais selected, this setting is ignored.
1. To set Interval Time between FC
press MODE (one long press), then
one short press. The below display
appears:
Default: A
Interval time between FC
Programmable Setting
Select Valve no.
2. Use and to adjust minutes.
(If A is selected, press SET to complete
this setting).
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to complete this setting.
• O
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
No pressure measuring process occurs
Display will shut o as in Auto Mode.

Getting Started
1
Parts Identification
1
12
Wires connections - DC
456
8
“Dryconn” #22 to #12 AWG
9
Programmable Setting
Default: Valve #1 (Max. three valves)
You have a choice of which # valve will be
operated by the controller.
In case of output #1 burnout, you can
connect the valve to output #2 and select
valve #2 to operate or #3.
1. To select the valve #. Press MODE (one
long press, then two short presses.
This display appears:
2. Use to select valve #1. Valve #1 remains,
valve #2 blinks. Or use to deselect
valve #1. Valve #1 disappears,
valve #2 blinks.
3. Repeat the above for valves 2 and 3.
Description
The Baccara Dierential Filtration Controller
combines a Controller and Dierential
Pressure Sensor (DP).
Molded DP with three wires cable. Controller
with seven wires for valves and sensor
interface.
The DFC controller is oered as DC Latch
only, and it is suitable for Baccara solenoid
Latch 4 ohm.
The controllers operates up to three
solenoids. The Controller shows the actual
DIF pressure and the pressure SET point.
The Flushing Cycle (FC) begins when
DIF≥SET appears.
Display
The LCD display shows:
• Actual DIF pressure
• SET point pressure
• FC counter
• Faucet icon displayed whilst FC operating
• Low battery icon appears when
battery needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
• Max. High pressure 14bar/200psi
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings
when power supply disconnected.
Mounting
DP: 2"/ 52mm diameter
2 ft/ 60 cm. 3 wires cable
High and low pressure ports 1/ 8”
BSP/NPT male
High pressure port marked on housing.
Important: Connect High pressure before
Low pressure. Disconnect Low pressure
before High pressure.
Electric cable Pipe fitting
Mounting
screws x 2
Pipe fitting
Controller (DFC display)
Upper digits
UD
Lower digits
LD
DP
White Black
Yellow
Blue
Green
G75
DFC
Black
Black
Red
Orange
Black
Red
Orange
Black
Di.
Sensor
3
1. Strip wires ¾" and group
bare wires ends together.
No pre-twisting
necessary with solid wire.
Pre-twist stranded wire. If
using both wire types,
wrap stranded wire
around solid wires.
See 1A.
2. Insert wires through
flexible sealing fingers
and bend wires wires into
either <V- Channel>.
3. Push inner sleeve into
pre-filled outer sleeve
until double-locked.
Pre-filled silicone fuller
waterproofs the
connection. Do not reuse
connector.
LV9000 - Wire connectors
Installation instructions
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires
with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• O
• FC counter rest
• Manual FC
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows counter value (see section 3).
LD shows DIF and SET values.
Whilst in FC, the faucet icon will turn on
and the operating valve number will blink.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) one minute
after no button is pressed (shut o).
Display will turn on with pressing any
button.
If DIF≥SET for (n) consecutive measuring
samples, FC starts. FC ends one min.
after the last valve shut down.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• FC Counter reset
1. From Auto Mode press MODE and
together UD will blink with
counter content.
2. For RESET, press MODE and
together, UD shows c000, then back
to Auto.
3. If RESET is not needed, press SET,
then back to Auto.
• Manual FC
1. From Auto Mode press SET and
together, FC starts.
Display shows "Hand" and "Faucet"
icons. VALVE and operating valve #
blink.
2. When FC is completed the MODE
returns to Auto.
3. To stop Manual FC press SET and
together, FC will stop and return to
Auto.
Factory Setting
These settings cannot be programmed by
the user:
• Pressure units: bar
• FC delay: 2 consecutive readings of
DIF≥SET before FC starts.
• Sample Interval time: Auto, as the
DIF becomes closer to the SET
point, the interval time between
samples shortens.
Max. Interval 60 secs./ Min.
Interval 5 sec.
• O time between valves during FC:
20 sec.
• Consecutive FC count number for
alarm: 5 count
• Sensor calibration.
Factory Setting
7
Valve on Time: default: 40 sec. range
(5 min. 59 sec.) Same time for all valves.
1. To set Valve on Time press MODE until
below display appears:
2. Use and to adjust seconds.
3. Press SET to continue.
4. Use and to adjust minutes.
5. Press SET to complete setting.
This interval value will be the max. time
between two consecutive FC if DIF
pressure does not execute FC.
Range (23 hrs: 59 min. A)
If Ais selected, this setting is ignored.
1. To set Interval Time between FC
press MODE (one long press), then
one short press. The below display
appears:
Default: A
Interval time between FC
Programmable Setting
Select Valve no.
2. Use and to adjust minutes.
(If A is selected, press SET to complete
this setting).
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to complete this setting.
• O
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
No pressure measuring process occurs
Display will shut o as in Auto Mode.

Getting Started
1
Parts Identification
1
12
Wires connections - DC
456
8
“Dryconn” #22 to #12 AWG
9
Programmable Setting
Default: Valve #1 (Max. three valves)
You have a choice of which # valve will be
operated by the controller.
In case of output #1 burnout, you can
connect the valve to output #2 and select
valve #2 to operate or #3.
1. To select the valve #. Press MODE (one
long press, then two short presses.
This display appears:
2. Use to select valve #1. Valve #1 remains,
valve #2 blinks. Or use to deselect
valve #1. Valve #1 disappears,
valve #2 blinks.
3. Repeat the above for valves 2 and 3.
Description
The Baccara Dierential Filtration Controller
combines a Controller and Dierential
Pressure Sensor (DP).
Molded DP with three wires cable. Controller
with seven wires for valves and sensor
interface.
The DFC controller is oered as DC Latch
only, and it is suitable for Baccara solenoid
Latch 4 ohm.
The controllers operates up to three
solenoids. The Controller shows the actual
DIF pressure and the pressure SET point.
The Flushing Cycle (FC) begins when
DIF≥SET appears.
Display
The LCD display shows:
• Actual DIF pressure
• SET point pressure
• FC counter
• Faucet icon displayed whilst FC operating
• Low battery icon appears when
battery needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
• Max. High pressure 14bar/200psi
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings
when power supply disconnected.
Mounting
DP: 2"/ 52mm diameter
2 ft/ 60 cm. 3 wires cable
High and low pressure ports 1/ 8”
BSP/NPT male
High pressure port marked on housing.
Important: Connect High pressure before
Low pressure. Disconnect Low pressure
before High pressure.
Electric cable Pipe fitting
Mounting
screws x 2
Pipe fitting
Controller (DFC display)
Upper digits
UD
Lower digits
LD
DP
White Black
Yellow
Blue
Green
G75
DFC
Black
Black
Red
Orange
Black
Red
Orange
Black
Di.
Sensor
3
1. Strip wires ¾" and group
bare wires ends together.
No pre-twisting
necessary with solid wire.
Pre-twist stranded wire. If
using both wire types,
wrap stranded wire
around solid wires.
See 1A.
2. Insert wires through
flexible sealing fingers
and bend wires wires into
either <V- Channel>.
3. Push inner sleeve into
pre-filled outer sleeve
until double-locked.
Pre-filled silicone fuller
waterproofs the
connection. Do not reuse
connector.
LV9000 - Wire connectors
Installation instructions
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires
with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• O
• FC counter rest
• Manual FC
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows counter value (see section 3).
LD shows DIF and SET values.
Whilst in FC, the faucet icon will turn on
and the operating valve number will blink.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) one minute
after no button is pressed (shut o).
Display will turn on with pressing any
button.
If DIF≥SET for (n) consecutive measuring
samples, FC starts. FC ends one min.
after the last valve shut down.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• FC Counter reset
1. From Auto Mode press MODE and
together UD will blink with
counter content.
2. For RESET, press MODE and
together, UD shows c000, then back
to Auto.
3. If RESET is not needed, press SET,
then back to Auto.
• Manual FC
1. From Auto Mode press SET and
together, FC starts.
Display shows "Hand" and "Faucet"
icons. VALVE and operating valve #
blink.
2. When FC is completed the MODE
returns to Auto.
3. To stop Manual FC press SET and
together, FC will stop and return to
Auto.
Factory Setting
These settings cannot be programmed by
the user:
• Pressure units: bar
• FC delay: 2 consecutive readings of
DIF≥SET before FC starts.
• Sample Interval time: Auto, as the
DIF becomes closer to the SET
point, the interval time between
samples shortens.
Max. Interval 60 secs./ Min.
Interval 5 sec.
• O time between valves during FC:
20 sec.
• Consecutive FC count number for
alarm: 5 count
• Sensor calibration.
Factory Setting
7
Valve on Time: default: 40 sec. range
(5 min. 59 sec.) Same time for all valves.
1. To set Valve on Time press MODE until
below display appears:
2. Use and to adjust seconds.
3. Press SET to continue.
4. Use and to adjust minutes.
5. Press SET to complete setting.
This interval value will be the max. time
between two consecutive FC if DIF
pressure does not execute FC.
Range (23 hrs: 59 min. A)
If Ais selected, this setting is ignored.
1. To set Interval Time between FC
press MODE (one long press), then
one short press. The below display
appears:
Default: A
Interval time between FC
Programmable Setting
Select Valve no.
2. Use and to adjust minutes.
(If A is selected, press SET to complete
this setting).
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to complete this setting.
• O
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
No pressure measuring process occurs
Display will shut o as in Auto Mode.

Getting Started
1
Parts Identification
1
12
Wires connections - DC
456
8
“Dryconn” #22 to #12 AWG
9
Programmable Setting
Default: Valve #1 (Max. three valves)
You have a choice of which # valve will be
operated by the controller.
In case of output #1 burnout, you can
connect the valve to output #2 and select
valve #2 to operate or #3.
1. To select the valve #. Press MODE (one
long press, then two short presses.
This display appears:
2. Use to select valve #1. Valve #1 remains,
valve #2 blinks. Or use to deselect
valve #1. Valve #1 disappears,
valve #2 blinks.
3. Repeat the above for valves 2 and 3.
Description
The Baccara Dierential Filtration Controller
combines a Controller and Dierential
Pressure Sensor (DP).
Molded DP with three wires cable. Controller
with seven wires for valves and sensor
interface.
The DFC controller is oered as DC Latch
only, and it is suitable for Baccara solenoid
Latch 4 ohm.
The controllers operates up to three
solenoids. The Controller shows the actual
DIF pressure and the pressure SET point.
The Flushing Cycle (FC) begins when
DIF≥SET appears.
Display
The LCD display shows:
• Actual DIF pressure
• SET point pressure
• FC counter
• Faucet icon displayed whilst FC operating
• Low battery icon appears when
battery needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
• Max. High pressure 14bar/200psi
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings
when power supply disconnected.
Mounting
DP: 2"/ 52mm diameter
2 ft/ 60 cm. 3 wires cable
High and low pressure ports 1/ 8”
BSP/NPT male
High pressure port marked on housing.
Important: Connect High pressure before
Low pressure. Disconnect Low pressure
before High pressure.
Electric cable Pipe fitting
Mounting
screws x 2
Pipe fitting
Controller (DFC display)
Upper digits
UD
Lower digits
LD
DP
White Black
Yellow
Blue
Green
G75
DFC
Black
Black
Red
Orange
Black
Red
Orange
Black
Di.
Sensor
3
1. Strip wires ¾" and group
bare wires ends together.
No pre-twisting
necessary with solid wire.
Pre-twist stranded wire. If
using both wire types,
wrap stranded wire
around solid wires.
See 1A.
2. Insert wires through
flexible sealing fingers
and bend wires wires into
either <V- Channel>.
3. Push inner sleeve into
pre-filled outer sleeve
until double-locked.
Pre-filled silicone fuller
waterproofs the
connection. Do not reuse
connector.
LV9000 - Wire connectors
Installation instructions
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires
with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• O
• FC counter rest
• Manual FC
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows counter value (see section 3).
LD shows DIF and SET values.
Whilst in FC, the faucet icon will turn on
and the operating valve number will blink.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) one minute
after no button is pressed (shut o).
Display will turn on with pressing any
button.
If DIF≥SET for (n) consecutive measuring
samples, FC starts. FC ends one min.
after the last valve shut down.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• FC Counter reset
1. From Auto Mode press MODE and
together UD will blink with
counter content.
2. For RESET, press MODE and
together, UD shows c000, then back
to Auto.
3. If RESET is not needed, press SET,
then back to Auto.
• Manual FC
1. From Auto Mode press SET and
together, FC starts.
Display shows "Hand" and "Faucet"
icons. VALVE and operating valve #
blink.
2. When FC is completed the MODE
returns to Auto.
3. To stop Manual FC press SET and
together, FC will stop and return to
Auto.
Factory Setting
These settings cannot be programmed by
the user:
• Pressure units: bar
• FC delay: 2 consecutive readings of
DIF≥SET before FC starts.
• Sample Interval time: Auto, as the
DIF becomes closer to the SET
point, the interval time between
samples shortens.
Max. Interval 60 secs./ Min.
Interval 5 sec.
• O time between valves during FC:
20 sec.
• Consecutive FC count number for
alarm: 5 count
• Sensor calibration.
Factory Setting
7
Valve on Time: default: 40 sec. range
(5 min. 59 sec.) Same time for all valves.
1. To set Valve on Time press MODE until
below display appears:
2. Use and to adjust seconds.
3. Press SET to continue.
4. Use and to adjust minutes.
5. Press SET to complete setting.
This interval value will be the max. time
between two consecutive FC if DIF
pressure does not execute FC.
Range (23 hrs: 59 min. A)
If Ais selected, this setting is ignored.
1. To set Interval Time between FC
press MODE (one long press), then
one short press. The below display
appears:
Default: A
Interval time between FC
Programmable Setting
Select Valve no.
2. Use and to adjust minutes.
(If A is selected, press SET to complete
this setting).
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to complete this setting.
• O
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
No pressure measuring process occurs
Display will shut o as in Auto Mode.

Getting Started
1
Parts Identification
1
12
Wires connections - DC
456
8
“Dryconn” #22 to #12 AWG
9
Programmable Setting
Default: Valve #1 (Max. three valves)
You have a choice of which # valve will be
operated by the controller.
In case of output #1 burnout, you can
connect the valve to output #2 and select
valve #2 to operate or #3.
1. To select the valve #. Press MODE (one
long press, then two short presses.
This display appears:
2. Use to select valve #1. Valve #1 remains,
valve #2 blinks. Or use to deselect
valve #1. Valve #1 disappears,
valve #2 blinks.
3. Repeat the above for valves 2 and 3.
Description
The Baccara Dierential Filtration Controller
combines a Controller and Dierential
Pressure Sensor (DP).
Molded DP with three wires cable. Controller
with seven wires for valves and sensor
interface.
The DFC controller is oered as DC Latch
only, and it is suitable for Baccara solenoid
Latch 4 ohm.
The controllers operates up to three
solenoids. The Controller shows the actual
DIF pressure and the pressure SET point.
The Flushing Cycle (FC) begins when
DIF≥SET appears.
Display
The LCD display shows:
• Actual DIF pressure
• SET point pressure
• FC counter
• Faucet icon displayed whilst FC operating
• Low battery icon appears when
battery needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
• Max. High pressure 14bar/200psi
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings
when power supply disconnected.
Mounting
DP: 2"/ 52mm diameter
2 ft/ 60 cm. 3 wires cable
High and low pressure ports 1/ 8”
BSP/NPT male
High pressure port marked on housing.
Important: Connect High pressure before
Low pressure. Disconnect Low pressure
before High pressure.
Electric cable Pipe fitting
Mounting
screws x 2
Pipe fitting
Controller (DFC display)
Upper digits
UD
Lower digits
LD
DP
White Black
Yellow
Blue
Green
G75
DFC
Black
Black
Red
Orange
Black
Red
Orange
Black
Di.
Sensor
3
1. Strip wires ¾" and group
bare wires ends together.
No pre-twisting
necessary with solid wire.
Pre-twist stranded wire. If
using both wire types,
wrap stranded wire
around solid wires.
See 1A.
2. Insert wires through
flexible sealing fingers
and bend wires wires into
either <V- Channel>.
3. Push inner sleeve into
pre-filled outer sleeve
until double-locked.
Pre-filled silicone fuller
waterproofs the
connection. Do not reuse
connector.
LV9000 - Wire connectors
Installation instructions
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires
with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• O
• FC counter rest
• Manual FC
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows counter value (see section 3).
LD shows DIF and SET values.
Whilst in FC, the faucet icon will turn on
and the operating valve number will blink.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) one minute
after no button is pressed (shut o).
Display will turn on with pressing any
button.
If DIF≥SET for (n) consecutive measuring
samples, FC starts. FC ends one min.
after the last valve shut down.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• FC Counter reset
1. From Auto Mode press MODE and
together UD will blink with
counter content.
2. For RESET, press MODE and
together, UD shows c000, then back
to Auto.
3. If RESET is not needed, press SET,
then back to Auto.
• Manual FC
1. From Auto Mode press SET and
together, FC starts.
Display shows "Hand" and "Faucet"
icons. VALVE and operating valve #
blink.
2. When FC is completed the MODE
returns to Auto.
3. To stop Manual FC press SET and
together, FC will stop and return to
Auto.
Factory Setting
These settings cannot be programmed by
the user:
• Pressure units: bar
• FC delay: 2 consecutive readings of
DIF≥SET before FC starts.
• Sample Interval time: Auto, as the
DIF becomes closer to the SET
point, the interval time between
samples shortens.
Max. Interval 60 secs./ Min.
Interval 5 sec.
• O time between valves during FC:
20 sec.
• Consecutive FC count number for
alarm: 5 count
• Sensor calibration.
Factory Setting
7
Valve on Time: default: 40 sec. range
(5 min. 59 sec.) Same time for all valves.
1. To set Valve on Time press MODE until
below display appears:
2. Use and to adjust seconds.
3. Press SET to continue.
4. Use and to adjust minutes.
5. Press SET to complete setting.
This interval value will be the max. time
between two consecutive FC if DIF
pressure does not execute FC.
Range (23 hrs: 59 min. A)
If Ais selected, this setting is ignored.
1. To set Interval Time between FC
press MODE (one long press), then
one short press. The below display
appears:
Default: A
Interval time between FC
Programmable Setting
Select Valve no.
2. Use and to adjust minutes.
(If A is selected, press SET to complete
this setting).
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to complete this setting.
• O
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
No pressure measuring process occurs
Display will shut o as in Auto Mode.

Getting Started
1
Parts Identification
1
12
Wires connections - DC
456
8
“Dryconn” #22 to #12 AWG
9
Programmable Setting
Default: Valve #1 (Max. three valves)
You have a choice of which # valve will be
operated by the controller.
In case of output #1 burnout, you can
connect the valve to output #2 and select
valve #2 to operate or #3.
1. To select the valve #. Press MODE (one
long press, then two short presses.
This display appears:
2. Use to select valve #1. Valve #1 remains,
valve #2 blinks. Or use to deselect
valve #1. Valve #1 disappears,
valve #2 blinks.
3. Repeat the above for valves 2 and 3.
Description
The Baccara Dierential Filtration Controller
combines a Controller and Dierential
Pressure Sensor (DP).
Molded DP with three wires cable. Controller
with seven wires for valves and sensor
interface.
The DFC controller is oered as DC Latch
only, and it is suitable for Baccara solenoid
Latch 4 ohm.
The controllers operates up to three
solenoids. The Controller shows the actual
DIF pressure and the pressure SET point.
The Flushing Cycle (FC) begins when
DIF≥SET appears.
Display
The LCD display shows:
• Actual DIF pressure
• SET point pressure
• FC counter
• Faucet icon displayed whilst FC operating
• Low battery icon appears when
battery needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
• Max. High pressure 14bar/200psi
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings
when power supply disconnected.
Mounting
DP: 2"/ 52mm diameter
2 ft/ 60 cm. 3 wires cable
High and low pressure ports 1/ 8”
BSP/NPT male
High pressure port marked on housing.
Important: Connect High pressure before
Low pressure. Disconnect Low pressure
before High pressure.
Electric cable Pipe fitting
Mounting
screws x 2
Pipe fitting
Controller (DFC display)
Upper digits
UD
Lower digits
LD
DP
White Black
Yellow
Blue
Green
G75
DFC
Black
Black
Red
Orange
Black
Red
Orange
Black
Di.
Sensor
3
1. Strip wires ¾" and group
bare wires ends together.
No pre-twisting
necessary with solid wire.
Pre-twist stranded wire. If
using both wire types,
wrap stranded wire
around solid wires.
See 1A.
2. Insert wires through
flexible sealing fingers
and bend wires wires into
either <V- Channel>.
3. Push inner sleeve into
pre-filled outer sleeve
until double-locked.
Pre-filled silicone fuller
waterproofs the
connection. Do not reuse
connector.
LV9000 - Wire connectors
Installation instructions
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires
with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• O
• FC counter rest
• Manual FC
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows counter value (see section 3).
LD shows DIF and SET values.
Whilst in FC, the faucet icon will turn on
and the operating valve number will blink.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) one minute
after no button is pressed (shut o).
Display will turn on with pressing any
button.
If DIF≥SET for (n) consecutive measuring
samples, FC starts. FC ends one min.
after the last valve shut down.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• FC Counter reset
1. From Auto Mode press MODE and
together UD will blink with
counter content.
2. For RESET, press MODE and
together, UD shows c000, then back
to Auto.
3. If RESET is not needed, press SET,
then back to Auto.
• Manual FC
1. From Auto Mode press SET and
together, FC starts.
Display shows "Hand" and "Faucet"
icons. VALVE and operating valve #
blink.
2. When FC is completed the MODE
returns to Auto.
3. To stop Manual FC press SET and
together, FC will stop and return to
Auto.
Factory Setting
These settings cannot be programmed by
the user:
• Pressure units: bar
• FC delay: 2 consecutive readings of
DIF≥SET before FC starts.
• Sample Interval time: Auto, as the
DIF becomes closer to the SET
point, the interval time between
samples shortens.
Max. Interval 60 secs./ Min.
Interval 5 sec.
• O time between valves during FC:
20 sec.
• Consecutive FC count number for
alarm: 5 count
• Sensor calibration.
Factory Setting
7
Valve on Time: default: 40 sec. range
(5 min. 59 sec.) Same time for all valves.
1. To set Valve on Time press MODE until
below display appears:
2. Use and to adjust seconds.
3. Press SET to continue.
4. Use and to adjust minutes.
5. Press SET to complete setting.
This interval value will be the max. time
between two consecutive FC if DIF
pressure does not execute FC.
Range (23 hrs: 59 min. A)
If Ais selected, this setting is ignored.
1. To set Interval Time between FC
press MODE (one long press), then
one short press. The below display
appears:
Default: A
Interval time between FC
Programmable Setting
Select Valve no.
2. Use and to adjust minutes.
(If A is selected, press SET to complete
this setting).
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to complete this setting.
• O
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
No pressure measuring process occurs
Display will shut o as in Auto Mode.
Getting Started
1
Parts Identification
1
12
Wires connections - DC
456
8
“Dryconn” #22 to #12 AWG
9
Programmable Setting
Default: Valve #1 (Max. three valves)
You have a choice of which # valve will be
operated by the controller.
In case of output #1 burnout, you can
connect the valve to output #2 and select
valve #2 to operate or #3.
1. To select the valve #. Press MODE (one
long press, then two short presses.
This display appears:
2. Use to select valve #1. Valve #1 remains,
valve #2 blinks. Or use to deselect
valve #1. Valve #1 disappears,
valve #2 blinks.
3. Repeat the above for valves 2 and 3.
Description
The Baccara Dierential Filtration Controller
combines a Controller and Dierential
Pressure Sensor (DP).
Molded DP with three wires cable. Controller
with seven wires for valves and sensor
interface.
The DFC controller is oered as DC Latch
only, and it is suitable for Baccara solenoid
Latch 4 ohm.
The controllers operates up to three
solenoids. The Controller shows the actual
DIF pressure and the pressure SET point.
The Flushing Cycle (FC) begins when
DIF≥SET appears.
Display
The LCD display shows:
• Actual DIF pressure
• SET point pressure
• FC counter
• Faucet icon displayed whilst FC operating
• Low battery icon appears when
battery needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
• Max. High pressure 14bar/200psi
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings
when power supply disconnected.
Mounting
DP: 2"/ 52mm diameter
2 ft/ 60 cm. 3 wires cable
High and low pressure ports 1/ 8”
BSP/NPT male
High pressure port marked on housing.
Important: Connect High pressure before
Low pressure. Disconnect Low pressure
before High pressure.
Electric cable Pipe fitting
Mounting
screws x 2
Pipe fitting
Controller (DFC display)
Upper digits
UD
Lower digits
LD
DP
White Black
Yellow
Blue
Green
G75
DFC
Black
Black
Red
Orange
Black
Red
Orange
Black
Di.
Sensor
3
1. Strip wires ¾" and group
bare wires ends together.
No pre-twisting
necessary with solid wire.
Pre-twist stranded wire. If
using both wire types,
wrap stranded wire
around solid wires.
See 1A.
2. Insert wires through
flexible sealing fingers
and bend wires wires into
either <V- Channel>.
3. Push inner sleeve into
pre-filled outer sleeve
until double-locked.
Pre-filled silicone fuller
waterproofs the
connection. Do not reuse
connector.
LV9000 - Wire connectors
Installation instructions
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires
with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• O
• FC counter rest
• Manual FC
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows counter value (see section 3).
LD shows DIF and SET values.
Whilst in FC, the faucet icon will turn on
and the operating valve number will blink.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) one minute
after no button is pressed (shut o).
Display will turn on with pressing any
button.
If DIF≥SET for (n) consecutive measuring
samples, FC starts. FC ends one min.
after the last valve shut down.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• FC Counter reset
1. From Auto Mode press MODE and
together UD will blink with
counter content.
2. For RESET, press MODE and
together, UD shows c000, then back
to Auto.
3. If RESET is not needed, press SET,
then back to Auto.
• Manual FC
1. From Auto Mode press SET and
together, FC starts.
Display shows "Hand" and "Faucet"
icons. VALVE and operating valve #
blink.
2. When FC is completed the MODE
returns to Auto.
3. To stop Manual FC press SET and
together, FC will stop and return to
Auto.
Factory Setting
These settings cannot be programmed by
the user:
• Pressure units: bar
• FC delay: 2 consecutive readings of
DIF≥SET before FC starts.
• Sample Interval time: Auto, as the
DIF becomes closer to the SET
point, the interval time between
samples shortens.
Max. Interval 60 secs./ Min.
Interval 5 sec.
• O time between valves during FC:
20 sec.
• Consecutive FC count number for
alarm: 5 count
• Sensor calibration.
Factory Setting
7
Valve on Time: default: 40 sec. range
(5 min. 59 sec.) Same time for all valves.
1. To set Valve on Time press MODE until
below display appears:
2. Use and to adjust seconds.
3. Press SET to continue.
4. Use and to adjust minutes.
5. Press SET to complete setting.
This interval value will be the max. time
between two consecutive FC if DIF
pressure does not execute FC.
Range (23 hrs: 59 min. A)
If Ais selected, this setting is ignored.
1. To set Interval Time between FC
press MODE (one long press), then
one short press. The below display
appears:
Default: A
Interval time between FC
Programmable Setting
Select Valve no.
2. Use and to adjust minutes.
(If A is selected, press SET to complete
this setting).
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to complete this setting.
• O
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
No pressure measuring process occurs
Display will shut o as in Auto Mode.

Getting Started
1
Parts Identification
1
12
Wires connections - DC
456
8
“Dryconn” #22 to #12 AWG
9
Programmable Setting
Default: Valve #1 (Max. three valves)
You have a choice of which # valve will be
operated by the controller.
In case of output #1 burnout, you can
connect the valve to output #2 and select
valve #2 to operate or #3.
1. To select the valve #. Press MODE (one
long press, then two short presses.
This display appears:
2. Use to select valve #1. Valve #1 remains,
valve #2 blinks. Or use to deselect
valve #1. Valve #1 disappears,
valve #2 blinks.
3. Repeat the above for valves 2 and 3.
Description
The Baccara Dierential Filtration Controller
combines a Controller and Dierential
Pressure Sensor (DP).
Molded DP with three wires cable. Controller
with seven wires for valves and sensor
interface.
The DFC controller is oered as DC Latch
only, and it is suitable for Baccara solenoid
Latch 4 ohm.
The controllers operates up to three
solenoids. The Controller shows the actual
DIF pressure and the pressure SET point.
The Flushing Cycle (FC) begins when
DIF≥SET appears.
Display
The LCD display shows:
• Actual DIF pressure
• SET point pressure
• FC counter
• Faucet icon displayed whilst FC operating
• Low battery icon appears when
battery needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
• Max. High pressure 14bar/200psi
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings
when power supply disconnected.
Mounting
DP: 2"/ 52mm diameter
2 ft/ 60 cm. 3 wires cable
High and low pressure ports 1/ 8”
BSP/NPT male
High pressure port marked on housing.
Important: Connect High pressure before
Low pressure. Disconnect Low pressure
before High pressure.
Electric cable Pipe fitting
Mounting
screws x 2
Pipe fitting
Controller (DFC display)
Upper digits
UD
Lower digits
LD
DP
White Black
Yellow
Blue
Green
G75
DFC
Black
Black
Red
Orange
Black
Red
Orange
Black
Di.
Sensor
3
1. Strip wires ¾" and group
bare wires ends together.
No pre-twisting
necessary with solid wire.
Pre-twist stranded wire. If
using both wire types,
wrap stranded wire
around solid wires.
See 1A.
2. Insert wires through
flexible sealing fingers
and bend wires wires into
either <V- Channel>.
3. Push inner sleeve into
pre-filled outer sleeve
until double-locked.
Pre-filled silicone fuller
waterproofs the
connection. Do not reuse
connector.
LV9000 - Wire connectors
Installation instructions
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires
with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• O
• FC counter rest
• Manual FC
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows counter value (see section 3).
LD shows DIF and SET values.
Whilst in FC, the faucet icon will turn on
and the operating valve number will blink.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) one minute
after no button is pressed (shut o).
Display will turn on with pressing any
button.
If DIF≥SET for (n) consecutive measuring
samples, FC starts. FC ends one min.
after the last valve shut down.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• FC Counter reset
1. From Auto Mode press MODE and
together UD will blink with
counter content.
2. For RESET, press MODE and
together, UD shows c000, then back
to Auto.
3. If RESET is not needed, press SET,
then back to Auto.
• Manual FC
1. From Auto Mode press SET and
together, FC starts.
Display shows "Hand" and "Faucet"
icons. VALVE and operating valve #
blink.
2. When FC is completed the MODE
returns to Auto.
3. To stop Manual FC press SET and
together, FC will stop and return to
Auto.
Factory Setting
These settings cannot be programmed by
the user:
• Pressure units: bar
• FC delay: 2 consecutive readings of
DIF≥SET before FC starts.
• Sample Interval time: Auto, as the
DIF becomes closer to the SET
point, the interval time between
samples shortens.
Max. Interval 60 secs./ Min.
Interval 5 sec.
• O time between valves during FC:
20 sec.
• Consecutive FC count number for
alarm: 5 count
• Sensor calibration.
Factory Setting
7
Valve on Time: default: 40 sec. range
(5 min. 59 sec.) Same time for all valves.
1. To set Valve on Time press MODE until
below display appears:
2. Use and to adjust seconds.
3. Press SET to continue.
4. Use and to adjust minutes.
5. Press SET to complete setting.
This interval value will be the max. time
between two consecutive FC if DIF
pressure does not execute FC.
Range (23 hrs: 59 min. A)
If Ais selected, this setting is ignored.
1. To set Interval Time between FC
press MODE (one long press), then
one short press. The below display
appears:
Default: A
Interval time between FC
Programmable Setting
Select Valve no.
2. Use and to adjust minutes.
(If A is selected, press SET to complete
this setting).
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to complete this setting.
• O
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
No pressure measuring process occurs
Display will shut o as in Auto Mode.

Getting Started
1
Parts Identification
1
12
Wires connections - DC
456
8
“Dryconn” #22 to #12 AWG
9
Programmable Setting
Default: Valve #1 (Max. three valves)
You have a choice of which # valve will be
operated by the controller.
In case of output #1 burnout, you can
connect the valve to output #2 and select
valve #2 to operate or #3.
1. To select the valve #. Press MODE (one
long press, then two short presses.
This display appears:
2. Use to select valve #1. Valve #1 remains,
valve #2 blinks. Or use to deselect
valve #1. Valve #1 disappears,
valve #2 blinks.
3. Repeat the above for valves 2 and 3.
Description
The Baccara Dierential Filtration Controller
combines a Controller and Dierential
Pressure Sensor (DP).
Molded DP with three wires cable. Controller
with seven wires for valves and sensor
interface.
The DFC controller is oered as DC Latch
only, and it is suitable for Baccara solenoid
Latch 4 ohm.
The controllers operates up to three
solenoids. The Controller shows the actual
DIF pressure and the pressure SET point.
The Flushing Cycle (FC) begins when
DIF≥SET appears.
Display
The LCD display shows:
• Actual DIF pressure
• SET point pressure
• FC counter
• Faucet icon displayed whilst FC operating
• Low battery icon appears when
battery needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
• Max. High pressure 14bar/200psi
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings
when power supply disconnected.
Mounting
DP: 2"/ 52mm diameter
2 ft/ 60 cm. 3 wires cable
High and low pressure ports 1/ 8”
BSP/NPT male
High pressure port marked on housing.
Important: Connect High pressure before
Low pressure. Disconnect Low pressure
before High pressure.
Electric cable Pipe fitting
Mounting
screws x 2
Pipe fitting
Controller (DFC display)
Upper digits
UD
Lower digits
LD
DP
White Black
Yellow
Blue
Green
G75
DFC
Black
Black
Red
Orange
Black
Red
Orange
Black
Di.
Sensor
3
1. Strip wires ¾" and group
bare wires ends together.
No pre-twisting
necessary with solid wire.
Pre-twist stranded wire. If
using both wire types,
wrap stranded wire
around solid wires.
See 1A.
2. Insert wires through
flexible sealing fingers
and bend wires wires into
either <V- Channel>.
3. Push inner sleeve into
pre-filled outer sleeve
until double-locked.
Pre-filled silicone fuller
waterproofs the
connection. Do not reuse
connector.
LV9000 - Wire connectors
Installation instructions
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires
with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• O
• FC counter rest
• Manual FC
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows counter value (see section 3).
LD shows DIF and SET values.
Whilst in FC, the faucet icon will turn on
and the operating valve number will blink.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) one minute
after no button is pressed (shut o).
Display will turn on with pressing any
button.
If DIF≥SET for (n) consecutive measuring
samples, FC starts. FC ends one min.
after the last valve shut down.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• FC Counter reset
1. From Auto Mode press MODE and
together UD will blink with
counter content.
2. For RESET, press MODE and
together, UD shows c000, then back
to Auto.
3. If RESET is not needed, press SET,
then back to Auto.
• Manual FC
1. From Auto Mode press SET and
together, FC starts.
Display shows "Hand" and "Faucet"
icons. VALVE and operating valve #
blink.
2. When FC is completed the MODE
returns to Auto.
3. To stop Manual FC press SET and
together, FC will stop and return to
Auto.
Factory Setting
These settings cannot be programmed by
the user:
• Pressure units: bar
• FC delay: 2 consecutive readings of
DIF≥SET before FC starts.
• Sample Interval time: Auto, as the
DIF becomes closer to the SET
point, the interval time between
samples shortens.
Max. Interval 60 secs./ Min.
Interval 5 sec.
• O time between valves during FC:
20 sec.
• Consecutive FC count number for
alarm: 5 count
• Sensor calibration.
Factory Setting
7
Valve on Time: default: 40 sec. range
(5 min. 59 sec.) Same time for all valves.
1. To set Valve on Time press MODE until
below display appears:
2. Use and to adjust seconds.
3. Press SET to continue.
4. Use and to adjust minutes.
5. Press SET to complete setting.
This interval value will be the max. time
between two consecutive FC if DIF
pressure does not execute FC.
Range (23 hrs: 59 min. A)
If Ais selected, this setting is ignored.
1. To set Interval Time between FC
press MODE (one long press), then
one short press. The below display
appears:
Default: A
Interval time between FC
Programmable Setting
Select Valve no.
2. Use and to adjust minutes.
(If A is selected, press SET to complete
this setting).
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to complete this setting.
• O
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
No pressure measuring process occurs
Display will shut o as in Auto Mode.

Getting Started
1
Parts Identification
1
12
Wires connections - DC
456
8
“Dryconn” #22 to #12 AWG
9
Programmable Setting
Default: Valve #1 (Max. three valves)
You have a choice of which # valve will be
operated by the controller.
In case of output #1 burnout, you can
connect the valve to output #2 and select
valve #2 to operate or #3.
1. To select the valve #. Press MODE (one
long press, then two short presses.
This display appears:
2. Use to select valve #1. Valve #1 remains,
valve #2 blinks. Or use to deselect
valve #1. Valve #1 disappears,
valve #2 blinks.
3. Repeat the above for valves 2 and 3.
Description
The Baccara Dierential Filtration Controller
combines a Controller and Dierential
Pressure Sensor (DP).
Molded DP with three wires cable. Controller
with seven wires for valves and sensor
interface.
The DFC controller is oered as DC Latch
only, and it is suitable for Baccara solenoid
Latch 4 ohm.
The controllers operates up to three
solenoids. The Controller shows the actual
DIF pressure and the pressure SET point.
The Flushing Cycle (FC) begins when
DIF≥SET appears.
Display
The LCD display shows:
• Actual DIF pressure
• SET point pressure
• FC counter
• Faucet icon displayed whilst FC operating
• Low battery icon appears when
battery needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
• Max. High pressure 14bar/200psi
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings
when power supply disconnected.
Mounting
DP: 2"/ 52mm diameter
2 ft/ 60 cm. 3 wires cable
High and low pressure ports 1/ 8”
BSP/NPT male
High pressure port marked on housing.
Important: Connect High pressure before
Low pressure. Disconnect Low pressure
before High pressure.
Electric cable Pipe fitting
Mounting
screws x 2
Pipe fitting
Controller (DFC display)
Upper digits
UD
Lower digits
LD
DP
White Black
Yellow
Blue
Green
G75
DFC
Black
Black
Red
Orange
Black
Red
Orange
Black
Di.
Sensor
3
1. Strip wires ¾" and group
bare wires ends together.
No pre-twisting
necessary with solid wire.
Pre-twist stranded wire. If
using both wire types,
wrap stranded wire
around solid wires.
See 1A.
2. Insert wires through
flexible sealing fingers
and bend wires wires into
either <V- Channel>.
3. Push inner sleeve into
pre-filled outer sleeve
until double-locked.
Pre-filled silicone fuller
waterproofs the
connection. Do not reuse
connector.
LV9000 - Wire connectors
Installation instructions
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires
with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• O
• FC counter rest
• Manual FC
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows counter value (see section 3).
LD shows DIF and SET values.
Whilst in FC, the faucet icon will turn on
and the operating valve number will blink.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) one minute
after no button is pressed (shut o).
Display will turn on with pressing any
button.
If DIF≥SET for (n) consecutive measuring
samples, FC starts. FC ends one min.
after the last valve shut down.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• FC Counter reset
1. From Auto Mode press MODE and
together UD will blink with
counter content.
2. For RESET, press MODE and
together, UD shows c000, then back
to Auto.
3. If RESET is not needed, press SET,
then back to Auto.
• Manual FC
1. From Auto Mode press SET and
together, FC starts.
Display shows "Hand" and "Faucet"
icons. VALVE and operating valve #
blink.
2. When FC is completed the MODE
returns to Auto.
3. To stop Manual FC press SET and
together, FC will stop and return to
Auto.
Factory Setting
These settings cannot be programmed by
the user:
• Pressure units: bar
• FC delay: 2 consecutive readings of
DIF≥SET before FC starts.
• Sample Interval time: Auto, as the
DIF becomes closer to the SET
point, the interval time between
samples shortens.
Max. Interval 60 secs./ Min.
Interval 5 sec.
• O time between valves during FC:
20 sec.
• Consecutive FC count number for
alarm: 5 count
• Sensor calibration.
Factory Setting
7
Valve on Time: default: 40 sec. range
(5 min. 59 sec.) Same time for all valves.
1. To set Valve on Time press MODE until
below display appears:
2. Use and to adjust seconds.
3. Press SET to continue.
4. Use and to adjust minutes.
5. Press SET to complete setting.
This interval value will be the max. time
between two consecutive FC if DIF
pressure does not execute FC.
Range (23 hrs: 59 min. A)
If Ais selected, this setting is ignored.
1. To set Interval Time between FC
press MODE (one long press), then
one short press. The below display
appears:
Default: A
Interval time between FC
Programmable Setting
Select Valve no.
2. Use and to adjust minutes.
(If A is selected, press SET to complete
this setting).
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to complete this setting.
• O
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
No pressure measuring process occurs
Display will shut o as in Auto Mode.

Getting Started
1
Parts Identification
1
12
Wires connections - DC
456
8
“Dryconn” #22 to #12 AWG
9
Programmable Setting
Default: Valve #1 (Max. three valves)
You have a choice of which # valve will be
operated by the controller.
In case of output #1 burnout, you can
connect the valve to output #2 and select
valve #2 to operate or #3.
1. To select the valve #. Press MODE (one
long press, then two short presses.
This display appears:
2. Use to select valve #1. Valve #1 remains,
valve #2 blinks. Or use to deselect
valve #1. Valve #1 disappears,
valve #2 blinks.
3. Repeat the above for valves 2 and 3.
Description
The Baccara Dierential Filtration Controller
combines a Controller and Dierential
Pressure Sensor (DP).
Molded DP with three wires cable. Controller
with seven wires for valves and sensor
interface.
The DFC controller is oered as DC Latch
only, and it is suitable for Baccara solenoid
Latch 4 ohm.
The controllers operates up to three
solenoids. The Controller shows the actual
DIF pressure and the pressure SET point.
The Flushing Cycle (FC) begins when
DIF≥SET appears.
Display
The LCD display shows:
• Actual DIF pressure
• SET point pressure
• FC counter
• Faucet icon displayed whilst FC operating
• Low battery icon appears when
battery needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
• Max. High pressure 14bar/200psi
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings
when power supply disconnected.
Mounting
DP: 2"/ 52mm diameter
2 ft/ 60 cm. 3 wires cable
High and low pressure ports 1/ 8”
BSP/NPT male
High pressure port marked on housing.
Important: Connect High pressure before
Low pressure. Disconnect Low pressure
before High pressure.
Electric cable Pipe fitting
Mounting
screws x 2
Pipe fitting
Controller (DFC display)
Upper digits
UD
Lower digits
LD
DP
White Black
Yellow
Blue
Green
G75
DFC
Black
Black
Red
Orange
Black
Red
Orange
Black
Di.
Sensor
3
1. Strip wires ¾" and group
bare wires ends together.
No pre-twisting
necessary with solid wire.
Pre-twist stranded wire. If
using both wire types,
wrap stranded wire
around solid wires.
See 1A.
2. Insert wires through
flexible sealing fingers
and bend wires wires into
either <V- Channel>.
3. Push inner sleeve into
pre-filled outer sleeve
until double-locked.
Pre-filled silicone fuller
waterproofs the
connection. Do not reuse
connector.
LV9000 - Wire connectors
Installation instructions
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires
with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• O
• FC counter rest
• Manual FC
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows counter value (see section 3).
LD shows DIF and SET values.
Whilst in FC, the faucet icon will turn on
and the operating valve number will blink.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) one minute
after no button is pressed (shut o).
Display will turn on with pressing any
button.
If DIF≥SET for (n) consecutive measuring
samples, FC starts. FC ends one min.
after the last valve shut down.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• FC Counter reset
1. From Auto Mode press MODE and
together UD will blink with
counter content.
2. For RESET, press MODE and
together, UD shows c000, then back
to Auto.
3. If RESET is not needed, press SET,
then back to Auto.
• Manual FC
1. From Auto Mode press SET and
together, FC starts.
Display shows "Hand" and "Faucet"
icons. VALVE and operating valve #
blink.
2. When FC is completed the MODE
returns to Auto.
3. To stop Manual FC press SET and
together, FC will stop and return to
Auto.
Factory Setting
These settings cannot be programmed by
the user:
• Pressure units: bar
• FC delay: 2 consecutive readings of
DIF≥SET before FC starts.
• Sample Interval time: Auto, as the
DIF becomes closer to the SET
point, the interval time between
samples shortens.
Max. Interval 60 secs./ Min.
Interval 5 sec.
• O time between valves during FC:
20 sec.
• Consecutive FC count number for
alarm: 5 count
• Sensor calibration.
Factory Setting
7
Valve on Time: default: 40 sec. range
(5 min. 59 sec.) Same time for all valves.
1. To set Valve on Time press MODE until
below display appears:
2. Use and to adjust seconds.
3. Press SET to continue.
4. Use and to adjust minutes.
5. Press SET to complete setting.
This interval value will be the max. time
between two consecutive FC if DIF
pressure does not execute FC.
Range (23 hrs: 59 min. A)
If Ais selected, this setting is ignored.
1. To set Interval Time between FC
press MODE (one long press), then
one short press. The below display
appears:
Default: A
Interval time between FC
Programmable Setting
Select Valve no.
2. Use and to adjust minutes.
(If A is selected, press SET to complete
this setting).
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to complete this setting.
• O
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
No pressure measuring process occurs
Display will shut o as in Auto Mode.

Getting Started
1
Parts Identification
1
12
Wires connections - DC
456
8
“Dryconn” #22 to #12 AWG
9
Programmable Setting
Default: Valve #1 (Max. three valves)
You have a choice of which # valve will be
operated by the controller.
In case of output #1 burnout, you can
connect the valve to output #2 and select
valve #2 to operate or #3.
1. To select the valve #. Press MODE (one
long press, then two short presses.
This display appears:
2. Use to select valve #1. Valve #1 remains,
valve #2 blinks. Or use to deselect
valve #1. Valve #1 disappears,
valve #2 blinks.
3. Repeat the above for valves 2 and 3.
Description
The Baccara Dierential Filtration Controller
combines a Controller and Dierential
Pressure Sensor (DP).
Molded DP with three wires cable. Controller
with seven wires for valves and sensor
interface.
The DFC controller is oered as DC Latch
only, and it is suitable for Baccara solenoid
Latch 4 ohm.
The controllers operates up to three
solenoids. The Controller shows the actual
DIF pressure and the pressure SET point.
The Flushing Cycle (FC) begins when
DIF≥SET appears.
Display
The LCD display shows:
• Actual DIF pressure
• SET point pressure
• FC counter
• Faucet icon displayed whilst FC operating
• Low battery icon appears when
battery needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
• Max. High pressure 14bar/200psi
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings
when power supply disconnected.
Mounting
DP: 2"/ 52mm diameter
2 ft/ 60 cm. 3 wires cable
High and low pressure ports 1/ 8”
BSP/NPT male
High pressure port marked on housing.
Important: Connect High pressure before
Low pressure. Disconnect Low pressure
before High pressure.
Electric cable Pipe fitting
Mounting
screws x 2
Pipe fitting
Controller (DFC display)
Upper digits
UD
Lower digits
LD
DP
White Black
Yellow
Blue
Green
G75
DFC
Black
Black
Red
Orange
Black
Red
Orange
Black
Di.
Sensor
3
1. Strip wires ¾" and group
bare wires ends together.
No pre-twisting
necessary with solid wire.
Pre-twist stranded wire. If
using both wire types,
wrap stranded wire
around solid wires.
See 1A.
2. Insert wires through
flexible sealing fingers
and bend wires wires into
either <V- Channel>.
3. Push inner sleeve into
pre-filled outer sleeve
until double-locked.
Pre-filled silicone fuller
waterproofs the
connection. Do not reuse
connector.
LV9000 - Wire connectors
Installation instructions
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires
with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• O
• FC counter rest
• Manual FC
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows counter value (see section 3).
LD shows DIF and SET values.
Whilst in FC, the faucet icon will turn on
and the operating valve number will blink.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) one minute
after no button is pressed (shut o).
Display will turn on with pressing any
button.
If DIF≥SET for (n) consecutive measuring
samples, FC starts. FC ends one min.
after the last valve shut down.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• FC Counter reset
1. From Auto Mode press MODE and
together UD will blink with
counter content.
2. For RESET, press MODE and
together, UD shows c000, then back
to Auto.
3. If RESET is not needed, press SET,
then back to Auto.
• Manual FC
1. From Auto Mode press SET and
together, FC starts.
Display shows "Hand" and "Faucet"
icons. VALVE and operating valve #
blink.
2. When FC is completed the MODE
returns to Auto.
3. To stop Manual FC press SET and
together, FC will stop and return to
Auto.
Factory Setting
These settings cannot be programmed by
the user:
• Pressure units: bar
• FC delay: 2 consecutive readings of
DIF≥SET before FC starts.
• Sample Interval time: Auto, as the
DIF becomes closer to the SET
point, the interval time between
samples shortens.
Max. Interval 60 secs./ Min.
Interval 5 sec.
• O time between valves during FC:
20 sec.
• Consecutive FC count number for
alarm: 5 count
• Sensor calibration.
Factory Setting
7
Valve on Time: default: 40 sec. range
(5 min. 59 sec.) Same time for all valves.
1. To set Valve on Time press MODE until
below display appears:
2. Use and to adjust seconds.
3. Press SET to continue.
4. Use and to adjust minutes.
5. Press SET to complete setting.
This interval value will be the max. time
between two consecutive FC if DIF
pressure does not execute FC.
Range (23 hrs: 59 min. A)
If Ais selected, this setting is ignored.
1. To set Interval Time between FC
press MODE (one long press), then
one short press. The below display
appears:
Default: A
Interval time between FC
Programmable Setting
Select Valve no.
2. Use and to adjust minutes.
(If A is selected, press SET to complete
this setting).
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to complete this setting.
• O
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
No pressure measuring process occurs
Display will shut o as in Auto Mode.
Getting Started
1
Parts Identification
1
12
Wires connections - DC
456
8
“Dryconn” #22 to #12 AWG
9
Programmable Setting
Default: Valve #1 (Max. three valves)
You have a choice of which # valve will be
operated by the controller.
In case of output #1 burnout, you can
connect the valve to output #2 and select
valve #2 to operate or #3.
1. To select the valve #. Press MODE (one
long press, then two short presses.
This display appears:
2. Use to select valve #1. Valve #1 remains,
valve #2 blinks. Or use to deselect
valve #1. Valve #1 disappears,
valve #2 blinks.
3. Repeat the above for valves 2 and 3.
Description
The Baccara Dierential Filtration Controller
combines a Controller and Dierential
Pressure Sensor (DP).
Molded DP with three wires cable. Controller
with seven wires for valves and sensor
interface.
The DFC controller is oered as DC Latch
only, and it is suitable for Baccara solenoid
Latch 4 ohm.
The controllers operates up to three
solenoids. The Controller shows the actual
DIF pressure and the pressure SET point.
The Flushing Cycle (FC) begins when
DIF≥SET appears.
Display
The LCD display shows:
• Actual DIF pressure
• SET point pressure
• FC counter
• Faucet icon displayed whilst FC operating
• Low battery icon appears when
battery needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
• Max. High pressure 14bar/200psi
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings
when power supply disconnected.
Mounting
DP: 2"/ 52mm diameter
2 ft/ 60 cm. 3 wires cable
High and low pressure ports 1/ 8”
BSP/NPT male
High pressure port marked on housing.
Important: Connect High pressure before
Low pressure. Disconnect Low pressure
before High pressure.
Electric cable Pipe fitting
Mounting
screws x 2
Pipe fitting
Controller (DFC display)
Upper digits
UD
Lower digits
LD
DP
White Black
Yellow
Blue
Green
G75
DFC
Black
Black
Red
Orange
Black
Red
Orange
Black
Di.
Sensor
3
1. Strip wires ¾" and group
bare wires ends together.
No pre-twisting
necessary with solid wire.
Pre-twist stranded wire. If
using both wire types,
wrap stranded wire
around solid wires.
See 1A.
2. Insert wires through
flexible sealing fingers
and bend wires wires into
either <V- Channel>.
3. Push inner sleeve into
pre-filled outer sleeve
until double-locked.
Pre-filled silicone fuller
waterproofs the
connection. Do not reuse
connector.
LV9000 - Wire connectors
Installation instructions
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires
with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• O
• FC counter rest
• Manual FC
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows counter value (see section 3).
LD shows DIF and SET values.
Whilst in FC, the faucet icon will turn on
and the operating valve number will blink.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) one minute
after no button is pressed (shut o).
Display will turn on with pressing any
button.
If DIF≥SET for (n) consecutive measuring
samples, FC starts. FC ends one min.
after the last valve shut down.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• FC Counter reset
1. From Auto Mode press MODE and
together UD will blink with
counter content.
2. For RESET, press MODE and
together, UD shows c000, then back
to Auto.
3. If RESET is not needed, press SET,
then back to Auto.
• Manual FC
1. From Auto Mode press SET and
together, FC starts.
Display shows "Hand" and "Faucet"
icons. VALVE and operating valve #
blink.
2. When FC is completed the MODE
returns to Auto.
3. To stop Manual FC press SET and
together, FC will stop and return to
Auto.
Factory Setting
These settings cannot be programmed by
the user:
• Pressure units: bar
• FC delay: 2 consecutive readings of
DIF≥SET before FC starts.
• Sample Interval time: Auto, as the
DIF becomes closer to the SET
point, the interval time between
samples shortens.
Max. Interval 60 secs./ Min.
Interval 5 sec.
• O time between valves during FC:
20 sec.
• Consecutive FC count number for
alarm: 5 count
• Sensor calibration.
Factory Setting
7
Valve on Time: default: 40 sec. range
(5 min. 59 sec.) Same time for all valves.
1. To set Valve on Time press MODE until
below display appears:
2. Use and to adjust seconds.
3. Press SET to continue.
4. Use and to adjust minutes.
5. Press SET to complete setting.
This interval value will be the max. time
between two consecutive FC if DIF
pressure does not execute FC.
Range (23 hrs: 59 min. A)
If Ais selected, this setting is ignored.
1. To set Interval Time between FC
press MODE (one long press), then
one short press. The below display
appears:
Default: A
Interval time between FC
Programmable Setting
Select Valve no.
2. Use and to adjust minutes.
(If A is selected, press SET to complete
this setting).
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to complete this setting.
• O
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
No pressure measuring process occurs
Display will shut o as in Auto Mode.

Getting Started
1
Parts Identification
1
12
Wires connections - DC
456
8
“Dryconn” #22 to #12 AWG
9
Programmable Setting
Default: Valve #1 (Max. three valves)
You have a choice of which # valve will be
operated by the controller.
In case of output #1 burnout, you can
connect the valve to output #2 and select
valve #2 to operate or #3.
1. To select the valve #. Press MODE (one
long press, then two short presses.
This display appears:
2. Use to select valve #1. Valve #1 remains,
valve #2 blinks. Or use to deselect
valve #1. Valve #1 disappears,
valve #2 blinks.
3. Repeat the above for valves 2 and 3.
Description
The Baccara Dierential Filtration Controller
combines a Controller and Dierential
Pressure Sensor (DP).
Molded DP with three wires cable. Controller
with seven wires for valves and sensor
interface.
The DFC controller is oered as DC Latch
only, and it is suitable for Baccara solenoid
Latch 4 ohm.
The controllers operates up to three
solenoids. The Controller shows the actual
DIF pressure and the pressure SET point.
The Flushing Cycle (FC) begins when
DIF≥SET appears.
Display
The LCD display shows:
• Actual DIF pressure
• SET point pressure
• FC counter
• Faucet icon displayed whilst FC operating
• Low battery icon appears when
battery needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
• Max. High pressure 14bar/200psi
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings
when power supply disconnected.
Mounting
DP: 2"/ 52mm diameter
2 ft/ 60 cm. 3 wires cable
High and low pressure ports 1/ 8”
BSP/NPT male
High pressure port marked on housing.
Important: Connect High pressure before
Low pressure. Disconnect Low pressure
before High pressure.
Electric cable Pipe fitting
Mounting
screws x 2
Pipe fitting
Controller (DFC display)
Upper digits
UD
Lower digits
LD
DP
White Black
Yellow
Blue
Green
G75
DFC
Black
Black
Red
Orange
Black
Red
Orange
Black
Di.
Sensor
3
1. Strip wires ¾" and group
bare wires ends together.
No pre-twisting
necessary with solid wire.
Pre-twist stranded wire. If
using both wire types,
wrap stranded wire
around solid wires.
See 1A.
2. Insert wires through
flexible sealing fingers
and bend wires wires into
either <V- Channel>.
3. Push inner sleeve into
pre-filled outer sleeve
until double-locked.
Pre-filled silicone fuller
waterproofs the
connection. Do not reuse
connector.
LV9000 - Wire connectors
Installation instructions
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires
with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• O
• FC counter rest
• Manual FC
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows counter value (see section 3).
LD shows DIF and SET values.
Whilst in FC, the faucet icon will turn on
and the operating valve number will blink.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) one minute
after no button is pressed (shut o).
Display will turn on with pressing any
button.
If DIF≥SET for (n) consecutive measuring
samples, FC starts. FC ends one min.
after the last valve shut down.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• FC Counter reset
1. From Auto Mode press MODE and
together UD will blink with
counter content.
2. For RESET, press MODE and
together, UD shows c000, then back
to Auto.
3. If RESET is not needed, press SET,
then back to Auto.
• Manual FC
1. From Auto Mode press SET and
together, FC starts.
Display shows "Hand" and "Faucet"
icons. VALVE and operating valve #
blink.
2. When FC is completed the MODE
returns to Auto.
3. To stop Manual FC press SET and
together, FC will stop and return to
Auto.
Factory Setting
These settings cannot be programmed by
the user:
• Pressure units: bar
• FC delay: 2 consecutive readings of
DIF≥SET before FC starts.
• Sample Interval time: Auto, as the
DIF becomes closer to the SET
point, the interval time between
samples shortens.
Max. Interval 60 secs./ Min.
Interval 5 sec.
• O time between valves during FC:
20 sec.
• Consecutive FC count number for
alarm: 5 count
• Sensor calibration.
Factory Setting
7
Valve on Time: default: 40 sec. range
(5 min. 59 sec.) Same time for all valves.
1. To set Valve on Time press MODE until
below display appears:
2. Use and to adjust seconds.
3. Press SET to continue.
4. Use and to adjust minutes.
5. Press SET to complete setting.
This interval value will be the max. time
between two consecutive FC if DIF
pressure does not execute FC.
Range (23 hrs: 59 min. A)
If Ais selected, this setting is ignored.
1. To set Interval Time between FC
press MODE (one long press), then
one short press. The below display
appears:
Default: A
Interval time between FC
Programmable Setting
Select Valve no.
2. Use and to adjust minutes.
(If A is selected, press SET to complete
this setting).
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to complete this setting.
• O
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
No pressure measuring process occurs
Display will shut o as in Auto Mode.

Getting Started
1
Parts Identification
1
12
Wires connections - DC
456
8
“Dryconn” #22 to #12 AWG
9
Programmable Setting
Default: Valve #1 (Max. three valves)
You have a choice of which # valve will be
operated by the controller.
In case of output #1 burnout, you can
connect the valve to output #2 and select
valve #2 to operate or #3.
1. To select the valve #. Press MODE (one
long press, then two short presses.
This display appears:
2. Use to select valve #1. Valve #1 remains,
valve #2 blinks. Or use to deselect
valve #1. Valve #1 disappears,
valve #2 blinks.
3. Repeat the above for valves 2 and 3.
Description
The Baccara Dierential Filtration Controller
combines a Controller and Dierential
Pressure Sensor (DP).
Molded DP with three wires cable. Controller
with seven wires for valves and sensor
interface.
The DFC controller is oered as DC Latch
only, and it is suitable for Baccara solenoid
Latch 4 ohm.
The controllers operates up to three
solenoids. The Controller shows the actual
DIF pressure and the pressure SET point.
The Flushing Cycle (FC) begins when
DIF≥SET appears.
Display
The LCD display shows:
• Actual DIF pressure
• SET point pressure
• FC counter
• Faucet icon displayed whilst FC operating
• Low battery icon appears when
battery needs replacing.
Mechanical
• Operating temperature -10ºC to + 60ºC
• Dust and water tight: IP66
• UV protection
• Max. High pressure 14bar/200psi
Electrical
• Power supply: DC unit - 9V battery
• Internal memory retains settings
when power supply disconnected.
Mounting
DP: 2"/ 52mm diameter
2 ft/ 60 cm. 3 wires cable
High and low pressure ports 1/ 8”
BSP/NPT male
High pressure port marked on housing.
Important: Connect High pressure before
Low pressure. Disconnect Low pressure
before High pressure.
Electric cable Pipe fitting
Mounting
screws x 2
Pipe fitting
Controller (DFC display)
Upper digits
UD
Lower digits
LD
DP
White Black
Yellow
Blue
Green
G75
DFC
Black
Black
Red
Orange
Black
Red
Orange
Black
Di.
Sensor
3
1. Strip wires ¾" and group
bare wires ends together.
No pre-twisting
necessary with solid wire.
Pre-twist stranded wire. If
using both wire types,
wrap stranded wire
around solid wires.
See 1A.
2. Insert wires through
flexible sealing fingers
and bend wires wires into
either <V- Channel>.
3. Push inner sleeve into
pre-filled outer sleeve
until double-locked.
Pre-filled silicone fuller
waterproofs the
connection. Do not reuse
connector.
LV9000 - Wire connectors
Installation instructions
1. Strip wires 13 mm.
2. Align frayed strands or conductors.
3. Do not pre-twist. Place stripped wires
with
ends even, lead stranded wires slightly.
4. Twist connector onto wires pushing firmly
until hand-tight. DO NOT over torque.
5. Swipe excess sealant in and around
conductors.
DO NOT REUSE.
Operating Modes
• Auto
• O
• FC counter rest
• Manual FC
UD = Upper Digits
LD = Lower Digits
Operating Modes
• Auto
This mode is the running mode of the
controller.
UD shows counter value (see section 3).
LD shows DIF and SET values.
Whilst in FC, the faucet icon will turn on
and the operating valve number will blink.
Battery icon will blink when low battery
is detected:
Display will turn OFF (blank) one minute
after no button is pressed (shut o).
Display will turn on with pressing any
button.
If DIF≥SET for (n) consecutive measuring
samples, FC starts. FC ends one min.
after the last valve shut down.
Press MODE shortly (0.5 sec.) to shift the
controller Mode from Auto to OFF or
backwards.
• FC Counter reset
1. From Auto Mode press MODE and
together UD will blink with
counter content.
2. For RESET, press MODE and
together, UD shows c000, then back
to Auto.
3. If RESET is not needed, press SET,
then back to Auto.
• Manual FC
1. From Auto Mode press SET and
together, FC starts.
Display shows "Hand" and "Faucet"
icons. VALVE and operating valve #
blink.
2. When FC is completed the MODE
returns to Auto.
3. To stop Manual FC press SET and
together, FC will stop and return to
Auto.
Factory Setting
These settings cannot be programmed by
the user:
• Pressure units: bar
• FC delay: 2 consecutive readings of
DIF≥SET before FC starts.
• Sample Interval time: Auto, as the
DIF becomes closer to the SET
point, the interval time between
samples shortens.
Max. Interval 60 secs./ Min.
Interval 5 sec.
• O time between valves during FC:
20 sec.
• Consecutive FC count number for
alarm: 5 count
• Sensor calibration.
Factory Setting
7
Valve on Time: default: 40 sec. range
(5 min. 59 sec.) Same time for all valves.
1. To set Valve on Time press MODE until
below display appears:
2. Use and to adjust seconds.
3. Press SET to continue.
4. Use and to adjust minutes.
5. Press SET to complete setting.
This interval value will be the max. time
between two consecutive FC if DIF
pressure does not execute FC.
Range (23 hrs: 59 min. A)
If Ais selected, this setting is ignored.
1. To set Interval Time between FC
press MODE (one long press), then
one short press. The below display
appears:
Default: A
Interval time between FC
Programmable Setting
Select Valve no.
2. Use and to adjust minutes.
(If A is selected, press SET to complete
this setting).
3. Press SET to continue.
4. Use and to adjust hours.
5. Press SET to complete this setting.
• O
This mode is for OFF season or to stop
Auto Mode permanently.
LD shows OFF.
No pressure measuring process occurs
Display will shut o as in Auto Mode.

Battery Installation
Replace the battery at the start of each
irrigation season and when the low battery
symbol appears.
Use a 9V alkaline top quality battery only.
1. Using a Phillips screw driver, remove the
four battery cover screws.
2. Remove the battery cover and seal.
3. Replace the battery.
4. After reattaching the seal, put the cover
back, and secure with the four screws.
G75 - DFC
Dierential Filtration
Controller
4257170101 (6/20)
• English
10 Maintenance
screws
Battery cover seal
When replacing the seal, push seal tabs
into slots.
11 12 Troubleshooting
No water
Battery dead
O Mode
Valve # select
is incorrect
Shut O
Sleep
Battery dead
Open water
Replace battery
Set Auto Mode
#Correct valve select
Press any button
Press MODE
Replace battery
No FC
occurance
Valve does
not work
Blank
display
Problem Cause Solution
Guarantee
Baccara products are guaranteed to be free from
defects in material and workmanship for a period
of one year from the date of delivery.
This guarantee does nor apply where equipment is
not used and installed strictly in accordance with
Baccara specifications and Users Guide. Neither
does it apply to failures caused by lightning strikes
or damage due to freezing temperatures or mecha-
nical causes (e.g. lawn mowers).
Baccara is not
To receive guarantee benefits, customers should
return defective units along with the receipt to the
nearest Baccara distributor.
Baccara reserves the right to alter, modify or
redesign its products, pricing and guarantee at all
times without creating any liability for the
obsolescence of customer inventory of such parts
or products.
This manufacturer guarantee policy may apply
differently in different countries.
liable for indirect, incidental or consequential
damage in connection with the use of equipment.
13
Flow Chart for G75 -DFC Dierential Filtration Controller
Users Guide
Mode
1 sec
Mode
Mode
Auto Mode No display
>2sec
Set valves
on time
Sec Min
Mode
Interval time
between
FC
if Min = A
select
Mode
Valves select
deselect
PROGRAMMING
3 valves
Min Hrs
®

Battery Installation
Replace the battery at the start of each
irrigation season and when the low battery
symbol appears.
Use a 9V alkaline top quality battery only.
1. Using a Phillips screw driver, remove the
four battery cover screws.
2. Remove the battery cover and seal.
3. Replace the battery.
4. After reattaching the seal, put the cover
back, and secure with the four screws.
G75 - DFC
Dierential Filtration
Controller
4257170101 (6/20)
• English
10 Maintenance
screws
Battery cover seal
When replacing the seal, push seal tabs
into slots.
11 12 Troubleshooting
No water
Battery dead
O Mode
Valve # select
is incorrect
Shut O
Sleep
Battery dead
Open water
Replace battery
Set Auto Mode
#Correct valve select
Press any button
Press MODE
Replace battery
No FC
occurance
Valve does
not work
Blank
display
Problem Cause Solution
Guarantee
Baccara products are guaranteed to be free from
defects in material and workmanship for a period
of one year from the date of delivery.
This guarantee does nor apply where equipment is
not used and installed strictly in accordance with
Baccara specifications and Users Guide. Neither
does it apply to failures caused by lightning strikes
or damage due to freezing temperatures or mecha-
nical causes (e.g. lawn mowers).
Baccara is not
To receive guarantee benefits, customers should
return defective units along with the receipt to the
nearest Baccara distributor.
Baccara reserves the right to alter, modify or
redesign its products, pricing and guarantee at all
times without creating any liability for the
obsolescence of customer inventory of such parts
or products.
This manufacturer guarantee policy may apply
differently in different countries.
liable for indirect, incidental or consequential
damage in connection with the use of equipment.
13
Flow Chart for G75 -DFC Dierential Filtration Controller
Users Guide
Mode
1 sec
Mode
Mode
Auto Mode No display
>2sec
Set valves
on time
Sec Min
Mode
Interval time
between
FC
if Min = A
select
Mode
Valves select
deselect
PROGRAMMING
3 valves
Min Hrs
®

Battery Installation
Replace the battery at the start of each
irrigation season and when the low battery
symbol appears.
Use a 9V alkaline top quality battery only.
1. Using a Phillips screw driver, remove the
four battery cover screws.
2. Remove the battery cover and seal.
3. Replace the battery.
4. After reattaching the seal, put the cover
back, and secure with the four screws.
G75 - DFC
Dierential Filtration
Controller
4257170101 (6/20)
• English
10 Maintenance
screws
Battery cover seal
When replacing the seal, push seal tabs
into slots.
11 12 Troubleshooting
No water
Battery dead
O Mode
Valve # select
is incorrect
Shut O
Sleep
Battery dead
Open water
Replace battery
Set Auto Mode
#Correct valve select
Press any button
Press MODE
Replace battery
No FC
occurance
Valve does
not work
Blank
display
Problem Cause Solution
Guarantee
Baccara products are guaranteed to be free from
defects in material and workmanship for a period
of one year from the date of delivery.
This guarantee does nor apply where equipment is
not used and installed strictly in accordance with
Baccara specifications and Users Guide. Neither
does it apply to failures caused by lightning strikes
or damage due to freezing temperatures or mecha-
nical causes (e.g. lawn mowers).
Baccara is not
To receive guarantee benefits, customers should
return defective units along with the receipt to the
nearest Baccara distributor.
Baccara reserves the right to alter, modify or
redesign its products, pricing and guarantee at all
times without creating any liability for the
obsolescence of customer inventory of such parts
or products.
This manufacturer guarantee policy may apply
differently in different countries.
liable for indirect, incidental or consequential
damage in connection with the use of equipment.
13
Flow Chart for G75 -DFC Dierential Filtration Controller
Users Guide
Mode
1 sec
Mode
Mode
Auto Mode No display
>2sec
Set valves
on time
Sec Min
Mode
Interval time
between
FC
if Min = A
select
Mode
Valves select
deselect
PROGRAMMING
3 valves
Min Hrs
®

Battery Installation
Replace the battery at the start of each
irrigation season and when the low battery
symbol appears.
Use a 9V alkaline top quality battery only.
1. Using a Phillips screw driver, remove the
four battery cover screws.
2. Remove the battery cover and seal.
3. Replace the battery.
4. After reattaching the seal, put the cover
back, and secure with the four screws.
G75 - DFC
Dierential Filtration
Controller
4257170101 (6/20)
• English
10 Maintenance
screws
Battery cover seal
When replacing the seal, push seal tabs
into slots.
11 12 Troubleshooting
No water
Battery dead
O Mode
Valve # select
is incorrect
Shut O
Sleep
Battery dead
Open water
Replace battery
Set Auto Mode
#Correct valve select
Press any button
Press MODE
Replace battery
No FC
occurance
Valve does
not work
Blank
display
Problem Cause Solution
Guarantee
Baccara products are guaranteed to be free from
defects in material and workmanship for a period
of one year from the date of delivery.
This guarantee does nor apply where equipment is
not used and installed strictly in accordance with
Baccara specifications and Users Guide. Neither
does it apply to failures caused by lightning strikes
or damage due to freezing temperatures or mecha-
nical causes (e.g. lawn mowers).
Baccara is not
To receive guarantee benefits, customers should
return defective units along with the receipt to the
nearest Baccara distributor.
Baccara reserves the right to alter, modify or
redesign its products, pricing and guarantee at all
times without creating any liability for the
obsolescence of customer inventory of such parts
or products.
This manufacturer guarantee policy may apply
differently in different countries.
liable for indirect, incidental or consequential
damage in connection with the use of equipment.
13
Flow Chart for G75 -DFC Dierential Filtration Controller
Users Guide
Mode
1 sec
Mode
Mode
Auto Mode No display
>2sec
Set valves
on time
Sec Min
Mode
Interval time
between
FC
if Min = A
select
Mode
Valves select
deselect
PROGRAMMING
3 valves
Min Hrs
®

Battery Installation
Replace the battery at the start of each irrigation season and when the low battery symbol appears. Use a 9V alkaline top quality battery only. 1. Using a Phillips screw driver, remove the four battery cover screws. 2. Remove the battery cover and seal. 3. Replace the battery. 4. After reattaching the seal, put the cover back, and secure with the four screws.
G75 - DFC
Dierential Filtration
Controller
4257170101 (6/20)
• English
10 Maintenance
screws
Battery cover seal
When replacing the seal, push seal tabs into slots.
11 12 Troubleshooting
No water Battery dead O Mode Valve # select is incorrect Shut O Sleep Battery dead
Open water Replace battery Set Auto Mode #Correct valve select Press any button Press MODE Replace battery
No FC occurance Valve does not work Blank display
Problem Cause Solution
Guarantee
Baccara products are guaranteed to be free from defects in material and workmanship for a period of one year from the date of delivery. This guarantee does nor apply where equipment is not used and installed strictly in accordance with Baccara specifications and Users Guide. Neither does it apply to failures caused by lightning strikes or damage due to freezing temperatures or mecha- nical causes (e.g. lawn mowers).
Baccara is not
To receive guarantee benefits, customers should return defective units along with the receipt to the
nearest Baccara distributor.
Baccara reserves the right to alter, modify or redesign its products, pricing and guarantee at all times without creating any liability for the obsolescence of customer inventory of such parts or products. This manufacturer guarantee policy may apply differently in different countries.
liable for indirect, incidental or consequential
damage in connection with the use of equipment.
13
Flow Chart for G75 -DFC Dierential Filtration Controller
Users Guide
Mode
1 sec
Mode
Mode
Auto Mode No display
>2sec
Set valves
on time
Sec Min
Mode
Interval time
between
FC
if Min = A
select
Mode
Valves select
deselect
PROGRAMMING
3 valves
Min Hrs
®