Baccara G75 User manual

G75 Irrigation Window
Controller
BACCARA
USERS GUIDE END
WINDOW
START
ON
ON
ON
ON
OFFOFFOFFOFF 14:0010:00

1
1
1
2
2
3
3
3
7
8
8
9
10
5
TABLE OF CONTENTS
Getting Started
FEATURES
PARTS IDENTIFICATION
BASIC CONTROLLER FUNCTIONS
INSTALLATION
MANUAL OPERATION
IRRIGATION CYCLE TABLE
Example
Programming the Controller
MEANING OF CONTROLLER ICONS
SETTING THE CLOCK
SETTING THE WINDOW
Setting Window Start Time
Setting the Window End Time
Setting the ON Time (Duration Time)
Setting the OFF Time (Interval)
Setting the Days
Example
Maintenance and Troubleshooting
BATTERY INSTALLATION
OFF SEASON
TROUBLESHOOTING
Contact and Service Information
GUARANTEE
CONTACT INFORMATION
5
6
7
10
13
13
14
15
16
16
17

Getting Started
Features
This Controller irrigates in cycles, during a window of
time according to your needs. New plantings may be
irrigated for short bursts, in defined intervals. Cycle
irrigation is also used for temperature control.
Operates in cycles during programmed window
Battery powered; no need for electrical hookup
Easy installation
Waterproof and weather resistant
Easy programming
Parts Identification
1. Top Cover
2. Controller Display
3. Solenoid
4. Controller
5. Water Flow Direction Arrow
6. Hydraulic Valve
BSP
1”
SET
MODE
3
4
5
6
8:00
1
2
G75 Irrigation Window Controller
1

Basic Controller Functions
This section gives a brief description of the Controller
buttons. See the following sections for further details.
MODE Button - Quick presses of the MODE button
turn the controller off, or on. Longer presses of the
MODE button put the Controller in programming mode.
SET Button - Press the SET button to set a function
and proceed.
- Use these buttons to increase and decrease
schedule functions.
Installation
1. Turn off the main faucet.
2. Install the valve in the irrigation system so that the
black arrow on the valve is pointing in the direction
of the water flow. The Controller may be swiveled
around to facilitate installation.
3. Occasionally the valve opens in transit. To ensure
that the valve is closed before you open the main
faucet, first make sure that the Controller is not
set to OFF (If it is set to OFF, press briefly on the
MODE button to turn it on.) Then press and
SET simultaneously to open, and press and
SET simultaneously to close, You are now ready to
program the Controller.
4. Turn on the main faucet.
G75 Irrigation Window Controller
2

Manual Operation
To manually open the valve, make sure that the Controller
is not set to OFF (If it is set to OFF, press briefly on the
MODE button), then press and SET simultaneously.
The irrigation will continue until the interval defined
has passed. If the irrigation duration has been set to zero,
the valve will close after one minute.
To stop irrigating, press and SET simultaneously.
Irrigation Cycle Table
G75 Irrigation Window Controller
3
Example
You have just planted new seedlings, and you wish to
water them for five minutes, every hour, during the
hottest part of the day, every day. Set your Window
Start Time to 10:00; Window End Time to 14:00; ON
(Duration) Time to 05 (minutes); and OFF (Interval)
Time to 1:00. Your table will look like this:
Window Start Time
Window End Time
ON Time (Duration)
OFF Time (Interval)
Sun. Mon. Tues. Wed. Thurs. Fri. Sat.

G75 Irrigation Window Controller
4
14:0010:00
Window Start Time
Window End Time
ON Time (Duration)
OFF Time (Interval)
Sun. Mon. Tues. Wed. Thurs. Fri. Sat.
10:00
14:00
05
1:00
WINDOW
START END
ON
OFF
ON
ON
ON OFFOFFOFF

NOTE: You cannot program the Controller
if it is set to manual operation (Page 3) or if
it set to OFF . To release from manual
operation press and SET simultaneously.
To release from OFF press briefly on the
MODE button.
Programming the
Controller
Meaning of Controller Icons
NOTE: Quick presses of the MODE button
turns the Controller off, or on.
Longer presses of the MODE button put
the Controller in programming mode.
1. Irrigating days
of the week
2. Cycle start (shows cycle
has started)
3. Irrigation
4. Timing or clock
5. Low battery
6. Time adjustment
G75 Irrigation Window Controller
5
1 2 3 4 5 6 7
START
1
3
64
2
5

Setting the Clock
If screen is blank, press MODE to activate.
To set the program, you must be in operating mode.
Before programming the Controller you must set
the clock.
1. Press MODE until the time adjustment icon
appears (The minutes will be flashing):
On this screen the numbers represent the current time.
2. Use the and the buttons to adjust the
minutes.
3. Press SET to continue.
4. Use the and the buttons to adjust the
hours.
5. Press SET to continue.
6. Use the and the buttons to select the
current day of the week. The selected day will
flash.
7. Press SET to return to operating mode.
G75 Irrigation Window Controller
6
1 2 3 4 5 6 7
Current
Time
Days of
the Week
Clock

Setting the Window
The Window is the time between the Start and End of
the irrigation. The cycle consists of the ON time (actual
irrigation time), and the OFF time (interval between
irrigations). The cycle recurs during the Window.
During programming, the screen will revert to operating
mode if left inactive for 30 seconds.
Setting Window Start Time
1. Press the MODE button until the clock settings
screen appears, then press MODE again until
the following screen appears (the minutes will
be flashing).
On this screen, the clock numbers refer to the time you
wish the Window to begin. flashes on the screen,
alternating with the numbers.
2. Use the and the buttons to adjust the
minutes.
3. Press SET to continue.
4. Use the and the buttons to adjust the
hours.
5. Press SET to continue.
G75 Irrigation Window Controller
7
1234567 1234567

G75 Irrigation Window Controller
8
Setting the Window End Time
The following screen will then appear:
On this screen, the clock numbers refer to the time you
wish the irrigation Window to end. flashes on
the screen, alternating with the numbers.
1. Use the and the buttons to adjust the
minutes.
2. Press SET to continue.
3. Use the and the buttons to adjust the
hours.
4. Press SET to continue.
1234567
1 2 3 4 5 6 7
On this screen, the numbers refer to the amount of time
the irrigation will be on, each time it activates within the
1 2 3 4 5 6 7 1 2 3 4 5 6 7
Setting the ON Time (Duration Time)
The following screen will then appear:

G75 Irrigation Window Controller
9
cycle. ON time is measured in seconds and minutes.
flashes on the screen, alternating with the numbers.
1. Use the and the buttons to adjust the
seconds.
2. Press SET to continue.
3. Use the and the buttons to adjust the
minutes.
4. Press SET to continue.
1. Use the and the buttons to adjust the
minutes.
2. Press SET to continue.
3. Use the and the buttons to adjust the
hours.
1234567
1 2 3 4 5 6 7
On this screen, the numbers refer to the interval between
irrigations within the cycle (measured in minutes and
hours). flashes on the screen, alternating with the
numbers.
Setting the OFF Time (Interval)
The following screen will then appear:

1. Press SET to reach the day you wish to irrigate.
The number (corresponding to the day of the
week) will flash.
2. Press to select that day (the square which
appears indicates day is selected).
3. Press to deselect a day.
4. Press SET until all days are programmed as
desired. Current day continues flashing.
5. Press SET to complete programming.
G75 Irrigation Window Controller
10
4. Press SET to continue.
Setting the Days
The following screen will then appear:
1234567
You must select the days you wish the irrigation
Window to operate.
You have just received a new batch of chicks, and a heat
wave is forecast. You need to cool the chicken coop with
short bursts (one minute) of the sprinkler system, every
half-hour, from 8:00 in the morning till 18:00. Make sure
the clock is set, and the day of the week is also set. Press
MODE twice to get to Window start time
Example

G75 IrrigationWindow Controller
11
screen (Str). Set this screen to 08:00. End screen then
appears. Set End to 18:00. The next screen is the ON
screen (Duration Time). Set this to 01 (minutes). The
OFF (Interval) screen should be set to 0:30. Each day of
the week should then be selected on the next screen.
The Controller is now programmed and will turn on the
system for one minute, every half-hour, between 8:00 in
the morning and 18:00 at night, until the Controller is
turned OFF, or the program is changed.

G75 Irrigation Window Controller
13
Battery Installation
Replace the battery at the start of each irrigation
season and when the low battery symbol appears.
1. Using a Phillips screwdriver, remove the
four battery cover screws.
2. Remove the battery cover and seal.
3. Replace the battery.
4. After reattaching the seal, put the cover back,
and secure with the four screws.
Maintenance and
Troubleshooting
Seal
Battery cover
Screws
When replacing
seal, push seal tabs
into slots.

Off Season
During the season when you do not need to water
your plants press the MODE button quickly until
OFF is displayed. DO NOT remove the battery.
The Controller is equipped with a backup
battery, and removing the main battery for long
periods will cause the backup battery to discharge.
14
G75 Irrigation Window Controller

G75 Irrigation Window Controller
15
PROBLEM
Controller does not
irrigate plants as
desired
Blank display
Water does not
turn off
CAUSE SOLUTION
Water at main faucet
is shut off Check faucet
Replace damaged
section
Replace battery
Press MODE to
activate
Hose cut or blocked
Battery dead
Check program and
clock settings
Controller set on
OFF
Controller improperly
programmed
Battery dead Replace battery
Valve blocked by
dirt or scale
Valve installed
backwards
Cautions Do not remove the battery
when the Controller is not in use
!
Troubleshooting
Press MODE to
activate screen
Controller in sleep
mode
Replace valve
Install valve so that
the arrow points in
the direction of the
water flow

Contact and Service
Information
G75 Irrigation Window Controller
16
Baccara products are guaranteed to be free from
defects in material and workmanship for a period of
one year from the date of delivery.
This guarantee does nor apply where equipment is not
used and installed strictly in accordance with Baccara
specifications and Users Guide. Neither does it apply to
failures caused by lightning strikes or damage due to
freezing temperatures or mechanical causes (e.g. lawn
mowers). Baccara is not liable for indirect, incidental or
consequential damage in connection with the use of
equipment.
To receive guarantee benefits, customers should return
defective units along with the receipt to the nearest
Baccara distributor.
Baccara reserves the right to alter, modify or redesign
its products, pricing and guarantee at all times without
creating any liability for the obsolescence of customer
inventory of such parts or products.
This manufacturer guarantee policy may apply
differently in different countries.
Guarantee

G75 Irrigation Window Controller
17
Contact information
FACTORYAND HEAD OFFICE
Baccara Automation Control
Kvutzat Geva, 18915, Israel
Tel: [phone]
Fax: [phone]
E-mail: [email protected]
Web Site: www.baccara-geva.com
Baccara # 42572003
11/2010

1234567
BACCARA
Baccara Automation Control
Head Office & Factory
Kvutzat Geva, 18915, Israel
Tel: [phone]
Fax: [phone]
e-mail: [email protected]
www.baccara.co.il
Version 06/06
#42572003
ON ON ON ON
OFF OFF OFF OFF
START END
10:00 14:00
WINDOW
START

FLOW CHART
FOR
G75 IRRIGATION
“WINDOW” CONTROLLER
OFF
Operating Mode
Set Clock and
Day of Week
Mode
Programming
Start
Mode
Mode>2S
Mode>2S
Set Program
No Display
Set
Minutes
+
_
Hours
+
_
Day
+
_
Set Set
Min
+
_Set Set
HrsHrs
+
_Set + _
+
_
Min
Set
Sec
+
_Set Set
Min
+
_Set + _
Min
Set Set
Select
+
_
Hrs
+
_
Deselect
Programming
End
On Off Day
7 Times
Str End