Backyard Creations 259-5061 User manual

ATTACH YOUR
RECEIPT HERE
Keep a copy of your proof of
purchase or order confirmation
which will be needed if you
need to contact us about
warranty coverage.
Purchase Date:
36" Round Galvanized Fire Ring
SKU: 259-5061
Mfr. Item #: 62558
WARNING
Improper installation, adjustment,
alteration, service or maintenance can
cause property damage, injury or death.
Read the installation, operation and
maintenance instructions thoroughly
before installing or servicing this
equipment.
WARNING
FOR OUTDOOR USE ONLY!
WARNING
This product can expose you to chemicals
including carbon monoxide which is known to the
State of California to cause birth defects or other
reproductive harm. For more information go to
www.P65Warnings.ca.gov.
05282019
Before returning to your retailer, our exceptional customer service is available Monday –
Friday, 9 a.m. – 6 p.m., EST.
Email us at [email protected].
Questions, problems, missing parts?

2
TABLE OF CONTENTS
Table of Contents Page 2
Before You Begin Page 2
Package Contents
Page 3
Safety Information
Page 4
Assembly Pages 5-6
Care and Maintenance
Warranty Information
BEFORE YOU BEGIN
Please read and understand this entire manual before attempting to assemble, operate or install this product. If
you have any questions regarding the product, please contact the retailer.
This manual contains important information about the assembly, operation and maintenance of this fire ring.
General safety information is presented in the first few pages and is also located throughout this manual. Keep
this manual for future reference and to educate new users of this product.
Page 7
Page 8
Contact us for assistance: [email protected]

1. This product is for outdoor use only,
and shall NOT be used in a building,
garage or any other enclosed area.
2. Do NOT use this fire ring for indoor
heating. TOXIC carbon monoxide
fumes can accumulate and cause
asphyxiation.
3. This fire ring is NOT for commercial
use.
4. This fire ring is NOT to be operated
by children.
5. This fire ring is NOT to be used in or
on boats or recreational vehicles.
6. Always use in accordance with all
applicable local, state and national
codes. Contact your local fire
department for details on outdoor
burning.
7. When using this fire ring, exercise
the same precautions you would
with any open fire.
8. The use of alcohol or prescription or
non-prescription drugs may impair
the consumer’s ability to properly
assemble or safely operate this fire
ring.
9. Do NOT use this fire ring without
reading the entire
“Owner’s Manual”.
10. This fire ring is for use with dry,
seasoned hardwood. It will burn
hotter, more completely and create
less smoke.
11. Do NOT burn charcoal briquets,
lump charcoal, manufactured logs,
driftwood, trash, leaves, paper,
cardboard, plywood, painted or
stained or pressure treated wood.
Avoid using softwoods such as pine
or cedar that can throw sparks.
12. Do NOT alter this fire ring in any
manner.
13. Do NOT use this fire ring until it is
COMPLETELY assembled, and all
parts are securely fastened and
tightened.
14. Do NOT store or use gasoline or
other flammable vapors or liquids
in the vicinity of this or any other
appliance.
15. Do NOT store or use an LP gas
cylinder within 10 feet
(3.05m) of this fire ring while it is in
operation.
16. Do NOT use this fire ring near
automobiles, trucks, vans or
recreational vehicles.
17. Do NOT use in an explosive
atmosphere. Keep outdoor area
clean and free from combustible
materials, gasoline and other
flammable liquids.
18. Do NOT use this fire ring under any
overhead or near any unprotected
combustible constructions. Avoid
using near or under overhanging
trees and shrubs.
19. Always use this fire ring on a hard,
level non-combustible surface such
as concrete, rock/stone or cleared,
compacted earth. An asphalt or
blacktop surface is not acceptable
for this purpose. Do NOT use on
wooden decks.
20. Always empty this fire ring before
each use.
21. Do NOT wear flammable or loose
clothing when operating this fire
ring.
22. Do NOT use in windy conditions.
23. Do NOT use gasoline, kerosene,
diesel fuel, lighter fluid or alcohol to
light or relight fires.
24. Keep all electrical cords away from
a hot fire ring.
25. All surfaces of this fire ring are hot
when in operation. To avoid burns,
do NOT touch fire ring until it has
completely cooled unless you are
wearing protective gear
(Potholders, gloves, BBQ mittens,
hot pads & etc.). Never touch ashes
or coals to see if they are hot.
26. Do NOT leave a lit fire ring
unattended, especially around
children and pets.
27. Do NOT attempt to move or store
this fire ring until all ashes and
coals are completely extinguished.
28. Do NOT remove ashes or coals
until they are completely and fully
extinguished.
29. Use heat-resistant gloves or hot
pads when contacting surfaces.
30. Use a long, sturdy fire tool when
adding or moving logs.
31. Do NOT overload the fire ring. Do
not add additional firewood until
the fire burns down.
32. Do NOT lean over this fire ring
when lighting or when in use.
33. Do NOT place a hot fire ring or hot
fire tools onto combustible surfaces
such as grass, wooden deck, or
furniture.
34. Avoid breathing smoke from the fire
and avoid getting it into your eyes.
35. This fire ring should be thoroughly
inspected and cleaned on a regular
basis.
36. After a period of storage and/or
non-use, check for signs of
damage and creosote build-up. Do
NOT operate until necessary repairs
and/or cleanup are executed.
37. Deaths, serious injury or damage to
property may occur if the above is
not followed exactly.
3
SAFETY INFORMATION
WARNING
FOR YOUR SAFETY
Contact us for assistance: [email protected]

4
PACKAGE CONTENTS
PART DESCRIPTION QTY
Fire Ring Section 4
HARDWARE CONTENTS
A
B
A
A
A
A
Bolt (10x20mm)
QTY: 16
Nut (10mm)
QTY: 16
Hex Wrench
QTY: 1
C D
Contact us for assistance: [email protected]
REQUIRED FOR ASSEMBLY
(not included)
Adjustable Wrench
(or 10mm socket or open-end wrench)

5
ASSEMBLY
PREPARATION
Before beginning assembly of this appliance, make sure all parts are present. Compare all parts with package contents list
and hardware as listed on page 4 of this manual. If any part is missing or damaged, do not attempt to assemble this
product. Contact customer service for replacement parts.
Estimated Assembly Time: 20 Minutes | DO NOT over tighten hardware!
Tools Required for Assembly (NOT included): Adjustable or 10mm wrench
1
Select 2 of the Fire Ring Sections A. Overlap the 4 holes
drilled in the right edge of the first section with the 4 holes
drilled in the left edge of the second section. (NOTE: the rolled
edge of each piece should be at the top and should align
closely with the adjoining section. If the rolled edges are
offset where the two pieces meet, switch the overlap.) Join
together using 4 Bolts B on the outside and 4 Nuts C on the
inside as shown. Tighten using your adjustable wrench and
the included Hex Wrench D but do not over-tighten.
2Attach the next Fire Ring Section A in the same manner as
detailed in Step 1. Tighten hardware using your adjustable
wrench and the included Hex Wrench D but do not over-
tighten.
3
A
B
A
C
Hardware Used: B Bolt x 4
C Nut x 4
A
A
B
C
Hardware Used: B Bolt x 4
C Nut x 4
C
B
Attach the final Fire Ring Section A in the same manner as
detailed in Step 1. Tighten hardware using your adjustable
wrench and the included Hex Wrench D but do not over-
tighten.
Hardware Used: B Bolt x 4
C Nut x 4
Contact us for assistance: [email protected]

6
4
ASSEMBLY
Complete the fire ring by attaching the final Fire Ring Section A
to the first section in the same manner as detailed in Step 1.
Tighten hardware using your adjustable wrench and the
included Hex Wrench D but do not over-tighten.
Hardware Used: B Bolt x 4
C Nut x 4
B
C
Your Galvanized Fire Ring is complete.
Please enjoy fires responsibly.
Contact us for assistance: [email protected]