Backyard Discovery Cedar Crest 43010 User manual

Owner’s Manual
FAQ’s
Assembly Instructions
Warranty Information
Cedar Crest
Wooden Playcenter - 2010
Model: 43010
Manufacturer: Backyard Discovery
3001 North Rouse
Pittsburg, KS 66762
Made in China
INS-43010-02
ev. 1/27/2012

Owner’s Manual Play Set
Rev1/25/12
Dear Customer:
Please read entire booklet completely before beginning the assembly process.
Equipment is recommended for use by children 3 to 10 years of age. Structures are not intended for public use.
The Company does not warranty any of its residential structures subjected to commercial use such as:
Daycare, Preschool, Nursery School, Recreational Park, or any similar Commercial Application.
WARNING: This Symbol points out important safety instructions which, if not followed, could endanger
the personal safety of yourself and your children and/or damage your property. You MUST read and
follow all instructions in this manual before attempting to use this playcenter.
WARNING: Children must NOT use this playcenter until unit has been completely assembled
and inspected by an adult to insure set has been properly installed and anchored.
Please follow all recommendations below. Failure to do so may result in the warranty being void and/or safety
violations that could result in serious injury. This manual contains helpful information concerning Assembly
Preparation, Installation Procedure, and Required Maintenance. Always keep the safety of your children in mind as
your play structure is being built and as your children play on the set. Before your children play on the set please
review the Operation Instructions with them to help ensure their safety .
PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. KEEP THEM IN A SAFE PLACE WHERE YOU CAN
REFER TO THEM AS NEEDED. IN ORDER TO PROVIDE YOU WITH THE MOST EFFICIENT SERVICE, IT IS REQUIRED THAT
YOU PROVIDE US WITH THE PART NUMBERS WHEN ORDERING PARTS.
For Your Records:
Please take time and fill out the information below. This information will be needed for warranty issues.
Where Purchased: ____________________
Date of Purchase: ____________________
Installation Date: _____________________
Installed by: _________________________
Tracking Number Reference Label
Remove label sticker from each carton and stick on the back side of ID plate. In the event of warranty
claim this will help identify your unit.
Staple Receipt Here

Owner’s Manual Play Set
Rev1/25/12
Please refer to the Assembly section of the Assembly Manual for Maximum Fall Height.
Positioning Your Playcenter
1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult
helper. Place in a flat area of your yard to minimize ground preparation.
2. Choose a level location for the equipment. This can reduce the likelihood of the play set
tipping over and loose-fill surfacing material washing away during heavy rains.
3. Place the equipment not less than 6 ft from any structure or obstruction such as a fence,
garage, house, overhanging branches, laundry lines, or electrical wires.
4. Provide enough room so that the children can use the equipment safely. For example, for
structures with multiple play activities, a slide should not exit in front of a swing.
5. It is a good idea to place your Playcenter in an area that is convenient for adults to watch
children at play.
6. Create a site free of obstacles that could cause injuries – such as low overhanging tree
branches, overhead wires, tree stumps and/or roots, large rocks, bricks and concrete.
Additional suggestions in the Suggested Playground Surfacing Section.
7. Do not build your playset on top of surfacing material.
8. Locate bare metal platforms and slides out of direct sunlight to reduce the likelihood of serious
burns. A slide that faces north will receive the least direct sunlight.
9. Separate active and quiet activities from each other. For example, locate sandboxes away
from swings or use a guardrail or barrier to separate the sandbox from the movement of the
swings.
Suggested Playground Surfacing
 Playground equipment should never be placed on hard surfaces such as concrete or asphalt.
 Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
 Shredded bark mulch, wood chips, fine sand and fine gravel, are added as shock absorbing
materials after assembly. If used properly these materials can absorb some of the impact of a
child’s fall.
 All surface material should extend a minimum of 6 feet in all directions around the play area.
 Do not apply playground surfacing until after the unit is completely constructed. Playset should
not be built on top of surfacing.
 Use containment, such as digging out around the perimeter and/or lining the perimeter with
landscape edging.
 Installations of rubber tiles or poured-in-place surfaces (other than loose-fill materials)
generally require a professional and are not “do-it-yourself” projects.
 Shall use Playground Surfacing Materials (other than loose-fill material) which comply with the
safety standard ASTM F1292 Standard Specification of Impact Attenuation of Surfacing
Materials within the Use Zone of Playground Equipment.

Owner’s Manual Play Set
Rev1/25/12
The following chart explains the fall height in feet from which a life threatening head injury
would not be expected
Critical Heights in feet (m) of Tested Materials
Material Uncompressed Depth Compressed Depth
6" (152mm) 9" (228mm) 12" (304mm) to 9" (228mm)
Wood Chips 7' (2.13m) 10' (3.05m) 11' (3.35m) 10' (3.05m)
Double-Shredded bark mulch 6' (1.83m) 10' (3.05m) 11' (3.35m) 7' (2.13m)
Engineered Wood Fibers 6' (1.83m) 7' (2.13m) >12' (3.66m) 6' (1.83m)
Fine Sand 5' (1.52m) 5' (1.52m) 9' (2.74m) 5' (1.52m)
Coarse Sand 5' (1.52m) 5' (1.52m) 6' (1.83m) 4' (1.22m)
Fine Gravel 5' (1.52m) 7' (2.13m) 10' (3.05m) 6' (1.83m)
Medium Gravel 5' (1.52m) 5' (1.52m) 6' (1.83m) 5' (1.52m)
Shredded Tires* 10-12' (3.0-3.6m) N/A N/A N/A
*This data is from tests conducted by independent testing laboratories on a 6-inch depth of uncompressed shredded tire samples produced by four manufacturers. The tests
reported critical heights, which varied from 10 feet to greater than 12 feet. t is recommended that persons seeking to install shredded tires as a protective surface request test
data from the supplier showing the critical height of the material when it was tested in accordance with ASTM F1292.
Operating Instructions:
NOTE: Your children’s safety is our #1 concern. Observing the following statements
and warnings reduces the likelihood of serious or fatal injury. Please review these
safety rules regularly with your children.
1. This Playcenter is designed for specific number of occupants whose combined weight should
not exceed a designated weight on the elevated floor or the swing area, the total Unit capacity
is outlined in the Basic Setup Dimensions section of instruction manual. The maximum fall
height and recommended play area is also available in the Basic Setup Dimensions section of
the manual for the specific unit.
2. On-site adult supervision is required.
3. Instruct children not to walk close to, in front of, behind, or between moving swings or other
moving playground equipment.
4. Instruct children to sit in and never stand on swings
5. Instruct children not to twist the chains and ropes and not to loop them over the top support
bar, since this may reduce the strength of the chain or rope.
6. Instruct children not to jump from swings or other playground equipment in motion.
7. Instruct children to not to push empty seats. The seat may hit them and cause serious injury.
8. Instruct and teach children to sit in the center of the swings with their full weight on the seats.
9. Instruct children not to use the equipment in a manner other than intended.
10.Instruct children to always go down slides feet first. Never slide head first.
11.Instruct children to look before they slide to make sure no one is at the bottom.
12.Instruct children to never run up a slide, as this increases their chances of falling.
13.The parents should have the children dress appropriately with well-fitting shoes. Loose
clothing such as scarves and ponchos should not be worn. Always take off, tie up or tuck in
cords and drawstrings on children’s clothing. These things can get caught on playground
equipment and strangle a child.
14.Instruct children not to climb when the equipment is wet.
15.Instruct children to never jump from a fort deck. They should always use the ladder, ramp or
slide.
16.Instruct children to never crawl or walk across the top of monkey bars.

Owner’s Manual Play Set
Rev1/25/12
17.Instruct children to never crawl on top of a fort roof.
18.Verify that any suspended climbing ropes, chain, or cable are secured at both ends and that
they cannot be looped back on it.
19.Instruct children not to attach items to the playground equipment that are not specifically
designed for use with the equipment, such as, but not limited to, jump ropes, clothesline, pet
leashes, cables and chain as they may cause a strangulation hazard.
20.Instruct children to never wrap their legs around swing chain.
21.Instruct children to never slide down the swing chain.
22.Instruct children to remove their bike or other sports helmet before playing on playground
equipment.
Maintenance Instructions:
1. Check all nuts and bolts twice monthly during the usage season and tighten as required. (But
not so tight that you crack the wood) We recommend you check the swing beam and
hardware every two weeks due to wood expansion and contraction. It is particularly important
that this procedure be followed at the beginning of each season.
2. Remove plastic swing seats and take indoors or do not use when the temperature drops below
32 ° F.
3. Reinstall any plastic parts, such as swing seats or any other items that were removed for the
cold season.
4. Oil all metallic moving parts monthly during the usage period.
5. Check all coverings for bolts and sharp edges twice monthly during usage season to be certain
they are in place. Replace when necessary. It is especially important to do this at the
beginning of each new season.
6. Check swing seats, ropes, cables and chains monthly during usage season for evidence of
deterioration. Replacement should be made of any swing seat that has developed cracks in
the plastic seats or has exposed metal in the edges of the swing seat. If there are already
exposed metal inserts on the edge of the seat, immediately remove the seats and chains to
prevent serious injury. Ropes, cables and chains should be removed and replaced if excessive
wear is found.
7. For rusted areas on metallic members such as monkey bars, hand supports, brackets, etc.
Sand and repaint, using a non lead-based paint meeting the requirements of Title 16 CRF Part
1303.
8. Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season
causing splinters to appear. Light sanding may be necessary to maintain a safe playing
environment. If you are treating your Playcenter with stain regularly, it will help prevent severe
checking/splitting and other weather damage.
9. We have applied a waterborne transparent stain to your unit. This is done for color only. Once
or twice a year, depending on your climate conditions, you must apply some type of protection
(sealant) to the wood of your unit. Prior to the application of sealant, lightly sand any “rough”
spots on your set. Please note this is a requirement of your warranty.
10.Creating and maintaining the Playcenter on a level location is very important. As your children
play, your Playcenter will slowly dig its way into the soil, and it is very important that it settles
evenly. Make sure the play set is level and true once each year or at the beginning of each
play season.
11.At the beginning, end and twice a month during every play season, rake and check depth of
loose fill protective surfacing materials to prevent compaction and to maintain appropriate
depth. Replace as necessary.

Owner’s Manual Play Set
Rev1/25/12
Disposal Instructions:
When the Playcenter use is no longer desired, it should be disassembled and disposed of in such
a way that no unreasonable hazards will exist at the time the unit is discarded.
Third Party Assembly:
Customer may, in their sole discretion, elect to use a third party person or service to assemble this
product. Backyard Discovery assumes no responsibility or liability for any charge incurred by the
Customer for any assembly services’.
Please see our warranty for more information about damaged and missing part replacement
coverage. Backyard Discovery will not reimburse Customer for the price of parts purchased.

Owner’s Manual Play Set
Rev1/25/12
APPENDIX A
Information on Playground Surfacing Materials:
The following information is from the United States Consumer Product Safety Commission’s
Information Sheet for playground surfacing material; also see the following website for additional
information: www.cpsc.gov/cpscpub/pubs/323.html.
X3. CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS
11
X3.1 The U.S. Consumer Pro uct Safety Commission (CPSC) estimates that about 100,000 playgroun equipment-
relate injuries resulting from falls to the groun surface are treate annually in U.S. hospital emergency rooms. Injuries
involving this hazar pattern ten to be among the most serious of all playgroun injuries, an have the potential to be
fatal, particularly when the injury is to the hea . The surface un er an aroun playgroun equipment can be a major
factor in etermining the injury-causing potential of a fall. It is self evi ent that a fall onto a shock-absorbing surface is
less likely to cause a serious injury than a fall onto a har surface. Playgroun equipment shoul never be place on
har surfaces such as concrete or asphalt an while grass may appear to be acceptable it may quickly turn to har
packe earth in areas of high traffic. Shre e bark mulch, woo chips, fine san or fin gravel are consi ere to be
acceptable shock absorbing surfaces when installe an maintaine at a sufficient epth un er an aroun playgroun
equipment.
X3.2 Table X3.1 lists the maximum height from which a chil woul not be expecte to sustain a life-threatening hea
injury in a fall onto four ifferent loose-fill surfacing materials if they are installe an maintaine at epths of 6, 9, an 12
in. However, it shoul be recognize that all injuries ue to falls cannot be prevente no matter what surfacing material
is use .
X3.3 It is recommen e that a shock absorbing material shoul exten a minimum of 6 ft in all irections from the
perimeter of stationary equipment such as climbers an sli es. However, because chil ren may eliberately jump from a
moving swing, the shock absorbing material shoul exten in the front an rear of a swing a minimum istance of 2
times the height of the pivot point measure from a point irectly beneath the pivot on the supporting structure.
X3.4 This information is inten e to assist in comparing the relative shock-absorbing properties of various materials. No
particular material is recommen e over another. However, each material is only effective when properly maintaine .
Materials shoul be checke perio ically an replenishe to maintain correct epth as etermine necessary for your
equipment. The choice of a material epen s on the type an height of the playgroun equipment, the availability of the
material in your area, an its cost.
11
This information has been extracte from the CPSC publications “Playgroun Surfacing — Technical
Information Gui e” an “Han book for Public Playgroun Safety.” Copies of these reports can be obtaine by sen ing
a postcar to: Office of Public Affairs, U.S. Consumer Pro uct Safety Commission, Washington, D.C., 20207 or call the
toll-free hotline: [phone].
The American Society for Testing an Materials takes no position respecting the vali ity of any parent right
asserte in connection with any item mentione in this stan ar . Users of this stan ar are expressly a vise that
etermination of the vali ity of any such parent rights, an the risk of infringement of such rights, are entirely their own
responsibility.
The stan ar is subject to revision at any time by the responsible technical committee an must be reviewe
every five years an if not revise , either approve or with rawn. Your comments are invite either for revision of this
stan ar or for a itional stan ar s an shoul be a resse to ASTM Hea quarters. Your comments will receive
careful consi eration at a meeting of the responsible technical committee, which you may atten . If you feel that your
comments have not receive a fair hearing you shoul make your views known to the ASTM Committee on Stan ar s.
100 Barr Harbor Drive, West Conshohocken, PA 19428.

Rev5/20/10 BRS
Play Set Assembly Manual FAQs:
1. Does the area for the playset need to be level?
Yes. Backyard Discovery recommends the playset be positioned on a flat level area for
maximum safety and durability. The stakes provided should be used to secure it firmly to the
ground.
2. What size area is recommended for the playset?
Backyard Discovery recommends at least a 6’ (six foot) perimeter around and above the playset
for maximum safety.
3. What age range is appropriate for the playsets?
Backyard Discovery playsets are recommended for children ages 3 – 10 years.
4. Is the wood treated with chemicals?
Backyard Discovery uses 100% Chinese Cedar wood which is naturally bug resistant, decay
and rot resistant. To help ensure your child’s safety, our wood is completely chemical free and
we do not use pressure-treated wood. The stain we use is a top coat using a water-based
product that is for appearance only.
5. How often should the playset be stained?
Backyard Discovery recommends the playset be stained once each year. A water or oil based
stain can be used at the customer’s discretion.
6. Why does it seem that my swing set is developing cracks?
Wood is a natural material; no two pieces are exactly alike. Each piece has its own
characteristics and personality and reacts differently to climate changes. When any wood
product is exposed to the elements, it develops “wood checks”. A check is the radial separation
of the wood fibers running with the grain of the wood. These are caused by the varying
temperature and moisture conditions. A check is not a crack – it does not affect the strength or
durability of the wood or structural integrity of the play set.
7. Do Backyard Discovery playsets come with a warranty?
Yes. All Backyard Discovery products carry a 1-year replacement warranty on all parts for
manufacturer’s defect. Our wood carries a 5 year warranty on rot and decay as well. Please see
warranty details for more information.
8. What is the best way to get started assembling the playset?
Backyard Discovery recommends taking all the parts out of the boxes and arranging them by
part number before you begin any assembly. This will not only allow faster assembly, but will
also identify any parts that may be missing or damaged so they can be replaced before
assembly. If parts are missing or need replacement, go to

Rev5/20/10 BRS
www.swingsetsonline.com/support.aspx and follow the prompts to order them. Next, read the
assembly manual and get the tools ready for the job as
recommended in the manual. If the assembly manual is lost or misplaced a new one can be
printed from Backyard Discovery’s website: www.swingsetsonline.com.
9. The playset seems to rock or sway too much. What’s wrong?
Rocking is caused by uneven ground or obstructions such as rocks, roots, etc. under the ground
rails. These should be removed and the ground underneath re-leveled to prevent rocking. Also
ensure the playset is securely staked to the ground using the stakes provided.
10. The 2”x4” boards do not measure 2”x 4”. Why not?
In the U.S. it is common practice to describe lumber dimensions using the rough cut sizes from
the sawmill and not the finished dimensions. Retailers, home stores, etc. all use this accepted
practice for describing lumber dimensions. However, Backyard Discovery playsets are designed
and constructed using the actual dimensions so everything fits properly and remains so during
the life of the playset.
11. The end beam is not straight up and down. Why not?
This is normal. Backyard Discovery designs playsets this way to ensure the strongest structure
possible. The slight angle adds strength and reduces rocking and twisting.
12. The S-hooks for the swings won’t close. What is wrong?
Backyard Discovery recommends placing them on a hard surface such as concrete (don’t do
this on anything that will dent such as metal or finished wood or glass which will break!). It will
take quite a few strokes, but the hooks will close.
For more information and frequently asked questions, please refer to our website at
www.swingsetsonline.com.

Tools Required for Installation:
(These are the tools that are generally required for assembly of our playsets. These tools are not included in the playset
purchase.)
(Level 24”) (Open end Wrenches (Nut drivers
½” & 7/16” ) ½” & 9/16” )
(T pe Me sure) (3/8” Drive R tchet, ½”& 9/16” std sockets (Cl w H mmer)
½” & 9/16 deep sockets)
( 3/8” Cordless Drill or Electric drill) (1/8”, 5/16” & (Drill tt chments:
3/8” drill bits) Phillips he d screw
3/8” Socket Driver
Torque he d screw)
(An Adult w/an (Phillips & Straight Blade (Rubber Mallet –Optional)
Adult helper) screw drivers)

T
TT
Th
hh
he
ee
e C
CC
Ce
ee
ed
dd
da
aa
ar
rr
r C
CC
Cr
rr
re
ee
es
ss
st
tt
t
W
WW
Wo
oo
oo
oo
od
dd
de
ee
en
nn
n P
PP
Pl
ll
la
aa
ay
yy
yc
cc
ce
ee
en
nn
nt
tt
te
ee
er
rr
r
A
AA
As
ss
ss
ss
se
ee
em
mm
mb
bb
bl
ll
ly
yy
y I
II
In
nn
ns
ss
st
tt
tr
rr
ru
uu
uc
cc
ct
tt
ti
ii
io
oo
on
nn
ns
ss
s
DATEREV
1/27/2012
B

19'-11"
[6.1 m]
10'-11"
[3.3 m]
31'-11"
[9.7 m]
25'-10 1/2"
[7.9 m]
B
BB
Ba
aa
as
ss
si
ii
ic
cc
c S
SS
Se
ee
et
tt
tu
uu
up
pp
p D
DD
Di
ii
im
mm
me
ee
en
nn
ns
ss
si
ii
io
oo
on
nn
ns
ss
s
Place the set on level groun , not less than 6 ft [2 m] from any structure or obstruction such
as a fence, garage, house, overhanging branches, laun ry lines, or electrical wires.
I
II
Im
mm
mp
pp
po
oo
or
rr
rt
tt
ta
aa
an
nn
nt
tt
t A
AA
As
ss
ss
ss
se
ee
em
mm
mb
bb
bl
ll
ly
yy
y N
NN
No
oo
ot
tt
te
ee
es
ss
s
1) While assembling unit, take time before an after each phase to make sure fort is level. If fort is
not level, assembly will be ifficult an improper assembly may result. Extra care must be taken to
insure the fort is square.
2) Pay close attention to the ITEMS NEEDED FOR EACH PHASE. They can be a valuable ai when
sorting your woo an har ware. Assembly will be ma e easier if items are sorte by phase.
3) Pay close attention to make sure you are using the correct har ware in the correct phases. Using
incorrect har ware may result in improper assembly.
4) Whenever a t-nut is use , follow these irections. Place t-nut in pre- rille hole. Tap in with hammer.
Place bolt with washers in the opposite si e. Han tighten to make sure the bolt is in the t-nut.
DO NOT over tighten.
5) Rea the steps of each phase thoroughly. The written steps may inclu e important information not
shown in the illustrations.
Safe play height: 14'-11 1/2" [2.7 m]
Maximum fall height: 6'-4 1/2" [1.9 m]
Safe Play Zone

PARTS IDENTIFICATION
2 REQ
E1 - W100680
36x86x2108 UPRIGHT
2 REQ
E2 - W100681
36x86x2108 UPRIGHT
1 REQ
K1 - W100682
16x134x1310 ROOF SWING BEAM SUPPORT
1 REQ
K2 - W100683
16x134x1310 ROOF SUPPORT
1 REQ
L1 - W100687
16x112x1528 FLOOR RAIL
2 REQ
L2 - W100684
16x112x1528 GROUN BOAR
1 REQ
L3 - W100685
16x112x1620 GROUN BOAR
1 REQ
J1 - W100709
24x60x560 WIN OW LE GE
1 REQ
L4 - W100688
16x112x762 FLOOR RAIL
4 REQ
J2 - W100710
24x60x86 EN FLOOR CLEAT
4 REQ
K9-2 - W100712
11x86x768 WALL BOAR
1 REQ
L5 - W100686
16x112x762 GROUN BOAR
6 REQ
K9-1 - W100713
11x86x400 WALL BOAR
1 REQ
L6 - W100694
16x112x1528 ARCHE RAIL
1 REQ
L7 - W100695
16x112x1528 SCULPTURE RAIL

PARTS IDENTIFICATION
1 REQ
M1 - W100690
16x86x1536 TENT SUPPORT
1 REQ
M2 - W100691
16x86x1528 FLOOR RAIL
2 REQ
M3 - W100692
16x86x1528 TARP SUPPORT
1 REQ
M4 - W100693
16x86x1528 TARP TOP SUPPORT
1 REQ
M7 - W100708
16x86x895 WALL BOARD
1 REQ
M8 - W100700
16x86x910 WALL RAIL
1 REQ
M9 - W100696
16x86x904 ANGLE BRA E
1 REQ
M10 - W100701
16x86x860 SAFETY BOARD
2 REQ
M11 - W100697
16x86x834 WALL BOARD
4 REQ
M12 - W100702
16x86x834 WALL BOARD
1 REQ
M13 - W100698
16x86x762 MONKEY BAR MOUNT
1 REQ
M14 - W100699
16x86x762 FLOOR BOARD
1 REQ
J3 - W100984
24x60x1528 FLOOR JOIST

PARTS IDENTIFICATION
15 REQ
M15 - W100704
16x86x760 FLOOR BOARD
1 REQ
M16 - W100703
16x86x858 TARP SUPPORT
4 REQ
K70 - W100953
16x134x558 ROCKWALL SLAT
4 REQ
M17 - W100705
16x86x690 PICKET
2 REQ
K71 - W100954
16x134x558 ROCKWALL SLAT
1 REQ
M77 - W100544
16x86x438 SLIDE BRACE
2 REQ
M19 - W100707
16x86x688 FLOOR BOARD 2 REQ
M78 - W100545
16x86x438 CE TER SLIDE BRACE
2 REQ
SP1 - W100711
24x24x1356 FLOOR SUPPORT CLEAT
2 REQ
E84 - W100952
36x86x2240 A-FRAME LEG
1 REQ
H83 - W100550
24x86x2260 A-FRAME GROU D BOARD
2 REQ
F72 - W100067
36x60x1982 MO KEY BAR UPRIGHT
2 REQ
E80 - W100066
36x86x1520 MO KEY BAR RAIL
2 REQ
H73 - W100024
24x86x1238 ROCK WALL RAIL
1 REQ
M80 - W100068
16x86x1540 MO KEY BAR GROU D BOARD
2 REQ
M79 - W100069
16x86x999 MO KEY BAR GROU D BRACE
2 REQ
F73 - W100070
36x60x477 MO KEY BAR RAIL BRACE
2 REQ
F71 - W100689
36x60x330 STA DARD A GLE BRACE
1 REQ
SB72 - W100604
50x134x2274 SWI G BEAM

4 REQ
BOLT WH 5/16x5-3/4
H100032
8 REQ
BOLT WH 5/16x2-1/2
H100014
10 REQ
BOLT WH 5/16x2
H100012
4 REQ
LAG SCREW WH 5/16x2-1/2
H100028
39 REQ
LAG SCREW WH 5/16x2
H100027
2 REQ
BOLT WH 5/16x1-3/4
H100011
2 REQ
LAG SCREW HEX 5/16x2
H100067
2 REQ
BOLT HEX 5/16x2-3/4
H100047
18 REQ
BOLT WH 5/16x1-1/2
H100010
3 REQ
BOLT WH 5/16x1-1/4
H100009
27 REQ
NUT BARREL WH 5/16x7/8
H100005
16 REQ
NUT BARREL WH 5/16x5/8
H100004
8 REQ
NUT BARREL 1/4x3/4
H100079
12 REQ
BOLT WH 5/16x1
H100008
10 REQ
BOLT WH 5/16x1/2
H100115
4 REQ
BOLT FA 3/8x1-1/2
H100001
4 REQ
BOLT CARR AGE 5/16x2
H100038
2 REQ
BOLT HEX 5/16x1-1/2
H100041
6 REQ
BOLT HEX 5/16x1
H100040
10 REQ
BOLT PTH 1/4x1
H100061
14 REQ
SCREW TAPP NG 14x1-1/2
H100109
12 REQ
SCREW TAPP NG 8x1/2
H100123
PARTS IDENTIFICATION

22 REQ
NUT LOCK 5/16
H100110
2 REQ
T-NUT 1/4
H100072
24 REQ
T-NUT 5/16
H100074
4 REQ
T-NUT 3/8
H100073
43 REQ
WASHER LOCK EXT 12x19
H100031
86 REQ
WASHER LOCK EXT 8x19
H100030
24 REQ
SCREW PFH 8x3
H100092
8 REQ
SCREW PFH 8x2-1/4
H100091
12 REQ
SCREW PFH 8x2
H100111
2 REQ
SCREW PFH 8x1-3/4
H100089
137 REQ
SCREW PFH 8x1-1/2
H100086
44 REQ
SCREW PFH 8x1-1/8
H100088
28 REQ
SCREW PFH 8x1
H100085
1 REQ
EM - SLIDE BED 8' YELLOW
A100056
1 REQ
HY - TARP 1522x2119
A100062
PARTS IDENTIFICATION
4 REQ
SCREW PWH 8x5/8
H100128

8 REQ
WASHER SPLIT 5/16
H100095
4 REQ
WASHER SAFETY 17x30
H100103
32 REQ
WASHER FLAT 8x27
H100105
22 REQ
WASHER FLAT 9x18
H100106
14 REQ
WASHER LOCK INT 8x15
H100108
4 REQ
EY - T BING CAP GLIDER S PPORT
A100067
4 REQ
BY - SWING HANGER Q ICK LINK
H100097
4 REQ
BZ - SWING HANGER Q ICK LINK
H100099
6 REQ
EJ - L BRACKET 54x67
A100053
4 REQ
EX - GLIDER B SHING BYD GREEN
A100066
8 REQ
FA - Q ICK LINK
A100069
PARTS IDENTIFICATION
2 REQ
T-40 Torx Wrench
A100041
2 REQ
T-40 Torx Bit
A100042

1 REQ
ES - L BRACKET GREEN 32x51
A100061
2 REQ
EA - HAND GRIP YELLOW PLASTIC
A100043
8 REQ
FQ - ETAL GROUND STAKE GREEN
A100085
1 REQ
EN - CLA P SWING BEA END GREEN
A100057
2 REQ
DK - GLIDER AR BYD GREEN
A100022
1 REQ
DL - GLIDER SEAT YELLOW
A100023
2 REQ
FB - SWING SEAT YELLOW
A100070
4 REQ
ER - CLI BING ROCK GREEN S ALL
A100060
1 REQ
EK - SLIDE RAIL 8' GREEN RIGHT
A100054
1 REQ
EL - SLIDE RAIL 8' GREEN LEFT
A100055
1 REQ
EQ - CLA P SWING BEA RH GREEN
A100059
1 REQ
EP - CLA P SWING BEA LH GREEN
A100058
2 REQ
EW - GLIDER SUPPORT BYD GREEN
A100065
3 REQ
HL - ETAL RUNG 487
A100006
3 REQ
EC - ETAL RUNG 559
A100045
PARTS IDENTIFICATION
4 REQ
EZ - CHAIN GREEN 51.25"
A100068
4 REQ
HW - CHAIN GREEN 44"
A100048
1 REQ
HC - BYD ID TAG (LARGE) 2011 WITH AGES
A100164
2 REQ
GD - L BRACKET 66x66x127
A100140

ITEMS FOR PHASE 1
DESCRIPTIONITEMQTY
ROCK WALL RAILH732
ROCKWALL SLATK70
4
ROCKWALL SLAT
K71
2
SCREW PFH 8x1-1/2" 24
ROCKWALL SLAT
K71
ROCKWALL SLAT
SCREW PFH 8x1-1/2"
ROCK WALL RAIL
H73
THESE S RFACES FL SH
BOTH SIDES
TOP
TOP
P
PP
Ph
hh
ha
aa
as
ss
se
ee
e N
NN
No
oo
ot
tt
te
ee
es
ss
s
● ASSEMBLE SLATS TO RAILS AS SHOWN.
● NOTE OREINTATION OF 4 CENTER SLATS,
BE S RE TO STAGGER BOARDS AS SHOWN.
● SEE DRAWING BELOW FOR SPACING OF SLATS
ON RAILS.
● SING SLATS AS A G IDE, PRE-DRILL TOP EDGES
OF RAILS WITH A 1/8" DRILL BIT, 1 1/4" DEEP,
FAIL RE TO PRE-DRILL MAY RES LT IN BOARD
SPLITTING.
NOTE ORIENTATION OF 4 CENTER SLAT HOLES
ALIGN FRONT EDGE OF SLAT
WITH TOP OF RAIL
PRE-DRILL TOP EDGE OF RAILS
8282828282
R
RR
Ro
oo
oc
cc
ck
kk
k W
WW
Wa
aa
al
ll
ll
ll
l A
AA
As
ss
ss
ss
se
ee
em
mm
mb
bb
bl
ll
ly
yy
y
P
PP
Ph
hh
ha
aa
as
ss
se
ee
e 1
11
1