Badger Basket LONDON DOLL PRAM Quick setup guide

1.0/0416/HF
LONDON DOLL PRAM
MODEL NUMBER*:
55564 - Gray
If you need product
parts, see below or Page 2!
Assembly and Use Instructions. Adult assembly Required.
Read all instructions before use.
This manual is part of the product and
must be saved for future reference.
VERSION CODE*:
1.0/0416/HF
* Model and Version numbers are needed
if replacement parts are requested
FOR REPLACEMENT PARTS:
Go to our web site: http://www.badgerbasket.com/parts
Or scan QR code at right with your smartphone

1.0/0416/HF
WARNING - CAUTION
WARNING
ADULT ASSEMBLY REQUIRED
DUE TO THE PRESENCE OF SMALL PARTS AND SHARP
POINTS DURING ASSEMBLY, KEEP OUT OF REACH OF
CHILDREN UNTIL ASSEMBLY IS COMPLETE.
BEFORE YOU BEGIN ASSEMBLY:
Check all parts. If anything is missing or not
satisfactory, please DO NOT call the store
or return the product to them. Please go online to:
http://www.badgerbasket.com/parts
Most problems are resolved
without you needing to leave home.
When contacting us, please have this
instruction manual, your product model number,
and your Version Code ready.
Your Model Number is: 55564
Your Version Code is: 1.0/0416/HF
READ ALL INSTRUCTIONS before use of this product. Use only the parts and
hardware provided by Badger Basket. Keep instructions for future use. Do not use the
product if it is damaged or broken. Periodically inspect the product to ensure all parts
remain tight. This item is a toy for dolls only. It is never to be used for real infants or
pets. No product is a substitute for adult supervision. Always supervise your child
during play. For children ages three (3) years and older. Never sit on or stand on the toy.
Badger Basket Company, PO Box 227, Edgar, WI 54426-0227 USA • Web: www.badgerbasket.com
Toll-Free (Mon-Thurs 7:00 AM-4:00 PM CST): 1-800-236-1310
Phone: [phone] • Fax: [phone]
CARE INSTRUCTIONS:
Spot clean fabric with cold water and mild detergent and air dry.
Wipe the frame clean with a damp cloth as needed and dry thoroughly.

1.0/0416/HF
(A) 1 - Metal Chassis (B) 2 - Large Wheel
(C) 2 - Small Wheel (D) 1 - Pram Body
(E) 1 - Handle
(F) 1 SET - Hardware Kit (4xBolt, 4xSpacer, 4xCap Nut, Allen Wrench, Cap Wrench)
(G) 1 SET - Fabric Bedding (1xPadded Mat, 1xPillow, 1xBoot)
PARTS AND HARDWARE INCLUDED:
STEP 1: REVIEW THE FINAL ASSEMBLY DIAGRAM ON THE
LAST PAGE OF THIS MANUAL FOR AN ASSEMBLY OVERVIEW.
Attach the SMALL WHEELS (C) to the shorter wheel posts on the
METAL CHASSIS (A). Attach the LARGE WHEELS (B) to the longer
wheel posts on the METAL CHASSIS (A). Push the metal bracket at the
center of the wheel inward to open it (PHOTOS 1 and 2), slide the wheel
onto the end of the post, and release the bracket. The bracket locks over
the tip of the rod, and if you tug on the wheel it should not come off.
STEP 2: Attach the PRAM BODY (D) to the METAL CHASSIS (A). Line up the four hinges on
the CHASSIS with the four brackets on the BODY, and snap them in (PHOTOS 3 and 4). The
canopy end of the BODY (D) attaches on the SMALL WHEEL (C) side of the CHASSIS (A).
PHOTO 3 - Line up the Hinge PHOTO 4 - Snap into place
D
ADA
< PHOTO 1
Metal Bracket
closed
PHOTO 2 >
Metal Bracket
pushed open

1.0/0416/HF
STEP 4: Place the PADDED MAT and PILLOW (G) inside the PRAM
BODY (D). Attach the BOOT (G) to the outside of the PRAM BODY
(D). The BOOT (G) has elastic loops that stretch around the spindles
on the BODY (D), and also snaps that snap to the canopy.
STEP 5: The canopy can be fully open with the hinges locked to keep
it up, or unlock the hinges and fold it at.
(A) Metal Chassis (B) Large Wheel (C) Small Wheel (D) Pram Body (E) Handle
(F) Hardware (Bolts, Spacers, Cap Nuts)
(G) Fabric Bedding (Padded Mat, Pillow, Boot)
FINAL ASSEMBLY:
A
B
C
E
F
D
G
Boot Snaps
and Spindles
STEP 3: Attach the HANDLE (E) to the PRAM BODY (D) using the
HARDWARE KIT (F) (FOUR BOLTS, FOUR SPACERS, FOUR CAP
NUTS, ALLEN WRENCH and CAP WRENCH). Align all the parts as
shown in PHOTO 5.
Cap Nut
Spacer
Bolt
Pram Body (D)
Handle (E)
PHOTO 5
B
C