Fisher-Price Y6941 User manual

fisher-price.com
Y6941
Please keep this instruction sheet for future reference,
as it contains important information.
Requires five “AA” (LR6) alkaline batteries (not included) for operation.
The batteries included in the truck are for demonstration purposes only.
Adult assembly is required. Required tool: Phillips screwdriver (not included).
Wipe with a clean, damp cloth. Do not immerse.
This toy has no consumer serviceable parts. Do not take apart.

2
Assembled Parts
Upper Ramp
Large Tree Canopy
Teeter-totter
Handle
Gate Platform
Peek-a-boo Door
Flag
Base
Canopy Swing
Hut Roof
WallTree
Lower Ramp
Part not shown: Label Sheet
CAUTION
This package contains small parts. For adult assembly only.
Ba
se
#6 x 58" (1,6 cm) Screw – 3
Shown Actual Size
Tighten all screw with a Phillips
screwdriver. Do not over-tighten.

3
• Turn the assembly over.
• Fit the post on the teeter-totter into the hole in the wall assembly.
Hint: You may need to turn the teeter-totter to fit it in place.
• Push to “snap” in place.
• Fit the tree onto the wall.
• Lay the assembly face down on a flat surface and insert a screw into the wall and tighten.
1
2
Assembly
Teeter-totter
Post
Tree
Wall
Tr
Screw
Back View
Back View

4
• Turn the assembly upright.
• Fit the tabs on to the bottom of the wall assembly into the slots in the base.
Hint: If the tabs on the wall assembly do not seem to fit, turn it around and try again!
• Push near each tab to “snap” in place.
3
Assembly
• At an angle, fit the peg on one side of the peek-a-boo door into the socket in the wall.
• Then, push to “snap” the other peg in place.
• Fit the tabs on the hut roof into the slots in the tree. Push to “snap” in place.
4
5
Peek-a-boo Door
Hut Roof

5
Assembly
• First fit the tab on the platform into the slot in the backside of the wall
A
. Then, fit the upper ramp into
the slot in the front of the wall
B
.
• Push to “snap” the platform and upper ramp into the wall.
6Upper Ramp
Platform
Back View
Back View
A
B
• From the back of the wall assembly, first fit the top of the lower ramp onto the tabs on the upper
ramp A. Then, fit the tab on the bottom of the lower ramp into the slot in the base B.
• Push to “snap” in place.
7
Lower Ramp
Upper Ramp Tabs
Base Slot
Back View
A
B

6
• Fit the canopy swing onto the outer tree branch, as shown. Push to “snap” in place.
8
Canopy Swing
• Fit the large tree canopy onto the remaining tree branch. Push to “snap” in place.
9
Large Tree Canopy
Assembly

7
• Fit the gate into the socket in the base, as shown. Push to “snap” in place.
11 Gate
• Fit the handle onto the pegs on the wall assembly.
• Insert two screws into the handle and tighten.
10
Handle
2 Screws
Assembly

8
• Before applying the labels, wipe the surface with a clean, dry cloth to remove any dust or oils.
• Place the labels exactly as shown in the illustration and avoid repositioning the labels.
• After applying a label, rub it firmly with a clean dry cloth, starting at the center, to remove any
air bubbles.
Decoration
1
3
2
5
9
8
7
4
6
• Insert the flag into any of the sockets in the assembly.
12
Flag
Assembly

9
Zoo
• Locate the battery compartment door on the bottom of the toy.
• Loosen the screw in the battery compartment door and remove it.
• Insert three, new “AA” (LR6) alkaline batteries.
• Replace the battery compartment door and tighten the screw. Do not over-tighten.
• If the zoo begins to operate erratically, you may need to reset the electronics. Slide the
power/volume switch off and then back on.
1,5V x 5
“AA” (LR6)
Battery Installation
• Protect the environment by not disposing of this product with household waste (2002/96/EC).
Check your local authority for recycling advice and facilities.
Truck
For best performance, we recommend replacing the batteries that came with this toy with two, new
“AA” (LR6) alkaline batteries.
• Locate the battery compartment on the bottom of the vehicle.
• Loosen the screw with a Phillips screwdriver and remove the door.
• Remove the exhausted batteries and dispose of them properly.
• Insert two, new “AA” (LR6) alkaline batteries.
• Replace the battery compartment door and tighten the screw. Do not over-tighten.
• If this product begins to operate erratically, you may need to reset the electronics. Remove the batteries and
reinsert them.
• When sounds from this toy become faint or stop, it’s time for an adult to change the batteries.
We recommend alkaline batteries for longer battery life.
When sounds become faint or stop, it's time for an adult to change the batteries.

10
ICES-003
NMB-003
• This Class B digital apparatus complies with Canadian ICES-003.
• Operation is subject to the following two conditions: (1) this device may not cause harmful interference
and (2) this device must accept any interference received, including interference that may cause
undesired operation.
• Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
• L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire
de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu,
même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury
or ruin your toy. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries from the
toy. Dispose of batteries safely. Do not dispose of this product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the toy before charging.
• If removable, rechargeable batteries are used, they are only to be charged under
adult supervision.

11
PRESS
PRESS
• Press the lily pad or nest
for sounds.
Slide the power/volume
switch on the bottom
of the toy ON with low
volume ; ON with
high volume ;
or OFF .
Zoo Fun!
• Fit an animal figure onto
the button on the base.
Each animal makes
different sounds!
• Press down on the ticket
booth and the ticket taker
will talk to you.
PRESS
PRESS
PRESS
PRESS
PRESS
PRESS
Press the seat
Press the seat
for fun sounds!
for fun sounds!

FCC Statement (United States Only)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment. This device complies with
Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference and (2) this device must accept any interference received, including
interference that may cause undesired operation.
CO
N
SU
MER
ASS
I
S
T
A
N
CE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa B.V., Gondel 1, 1186MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
PRINTED IN MEXICO Y6941a-0920
©2012 Mattel. All Rights Reserved.