Badger Meter Impeller 228PV150U Series User manual

Flow Sensors
Wireless Flow Sensor System
Series 228PV
User Manual
SEN-UM-01662-EN-05 (March 2017)

Flow Sensors, Wireless Flow Sensor System
Page ii March 2017SEN-UM-01662-EN-05
CONTENTS
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Series 228PV Wireless Flow Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Wireless ORION RF Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Wireless ORION RF Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Wireless 228PV Plastic Tee Sensor and Transmitter Mechanical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Wireless Receiver Mechanical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Antenna Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Wireless Receiver Electrical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Theory of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Programming Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Wireless Receiver Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Wireless Flow Sensor Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Introduction
Page 3March 2017 SEN-UM-01662-EN-05
INTRODUCTION
The Series 228PV wireless flow sensor system from Badger Meter® consists of the flow sensor mounted in a tee (flow sensor
assembly), ORION® radio frequency (RF) transmitter complete with mounting kit, and ORION RF receiver/pulse transmitter.
This system eliminates the need for expensive signal wires from the sensor output.
The battery powered flow sensor performs flow measurement and scaling and then transmits a total flow value to the RF
transmitter. The transmitter sends an RF signal approximately every four seconds that the RF receiver detects. The RF receiver
compares the previous flow total with the most recent flow total to generate a pulse output. Using the PC software, which
is part of the software installation kit, the pulse output can be scaled to represent the desired volume unit and number of
output pulses per unit volume that best fits the application. Pulse width can also be adjusted to meet the requirements of an
interfacing control system or monitor.
LICENSE REQUIREMENTS
ORION Fixed Network, Migratable and Classic endpoints comply with Part 15 of FCC Rules. ORION Cellular endpoints comply
with Part 15, Part 22 and Part 24 of FCC Rules. Operation is subject to the following conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation of the device.
In accordance with FCC Regulations,“Code of Federal Regulations”Title 47, Part 2, Subpart J, Section 1091, transmitters
pass the requirements pertaining to radiation exposure. However, to avoid public exposure in excess of limits for general
population (uncontrolled exposure), a 20 centimeter distance between the transmitter and the body of the user must be
maintained during operation.
No FCC license is required by a utility to operate an ORION meter reading system.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur
de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre
le fonctionnement.
MPORTANTI
Transportation: The Federal Aviation Administration prohibits operating endpoints and receivers on all commercial aircraft. The
ORION endpoint is considered an operating transmitter and cannot be shipped by air.

Introduction
Page 4 March 2017SEN-UM-01662-EN-05
Figure 1: Series 228PV wireless flow sensor system
Series 228PV Wireless Flow Sensor
The four-bladed impeller design is rugged, non-fouling and does not require custom calibration. Coupled with the proprietary
patented digital detection circuit, the sensor measures flow rate from 1 foot per second (fps) to more than 20 fps, regardless
of conductivity or turbidity of the liquid. The flow sensor generates a frequency which is proportional to flow rate. An integral
micro controller measures the impeller frequency and uses the appropriate K factor and Offset values to compute the flow
rate. By means of integration, the volume total is calculated. The output signal to the RF transmitter is a scaled output pulse.
An internal lithium battery provides power for the flow sensor and is encapsulated to ensure moisture resistance.
Wireless ORION RF Transmitter
The ORION transmitter operates in the 902…928 MHz frequency band at a power level that requires no FCC licensing. The
transmitter is powered using an internal lithium battery and is encapsulated for moisture resistance. It is factory programmed
and requires no configuration.
Wireless ORION RF Receiver
The ORION receiver is powered using an external alternating current (AC) or direct current (DC) power supply. The wireless
receiver receives the scaled total from the transmitter. Further scaling and unit conversion can be programmed into the
receiver. The optically coupled scaled pulse output emulates a dry contact closure to ensure interfacing into various types of
controller inputs.

Installation
Page 5March 2017 SEN-UM-01662-EN-05
INSTALLATION
General
As with all flow measuring devices, accuracy is highly dependent on proper location of the sensor in the piping system.
Irregular flow velocity profiles caused by valves, fittings, pipe bends, etc. can lead to inaccurate overall flow rate indications,
even though local flow velocity measurement can be accurate. A sensor located in the pipe where it can be affected by air
bubbles, floating debris, or sediment can not achieve full accuracy and could be damaged.
Minimum Distance Minimum Distance
10 x I.D. 5 x I.D.
Power
Supply
FLOW
Flow Sensor
Valve Box Cover
Wireless
Transmitter
Antenna
MaxDistanec 500’
5’ Cable
Pulse
Output
Figure 2: Typical wireless flow sensor installation
Badger Meter flow sensors are designed to operate reliably under adverse conditions, but the following recommendations
should be followed to ensure maximum system accuracy.
1. Choose a location along the pipe with a length equivalent
to 10 pipe diameters upstream and 5 pipe diameters
downstream of the sensor which are free of ow
disturbances. Pipe bends, valves, other ttings, pipe
enlargements, and reductions should not be present in
this length of pipe.
2. When the ow sensor assembly is installed in horizontal
piping, the preferred orientation is vertical, on top of the
pipe (Figure 3). If trapped air or debris could potentially
interfere with sensor operation, the sensor can be
installed as much as 45 degrees o the vertical.
OTE:N When the sensor is installed“off the vertical”,
impeller friction increases, which can affect
performance at low flow rates and increase wear.
The ow sensor assembly should never be located at the
bottom of the pipe, as sediment can collect there. When
the ow sensor assembly is installed in vertical piping, it
can be installed at any circumferential position. Rising flow
is preferred to reduce the effects of trapped air. Figure 3: Flow sensor assembly in horizontal piping

Installation
Page 6 March 2017SEN-UM-01662-EN-05
Wireless 228PV Plastic Tee Sensor and Transmitter Mechanical Installation
1. Note the intended direction of ow as indicated by the arrows on the tee. Make sure there is free, unrestricted pipe for at
least 10 diameters upstream and 5 diameters downstream of the tee.
OTE:N Cable length between the sensor and wireless transmitter is 5 feet. Plan for cover removal if inserting into a valve box.
2. Remove the clevis pin and remove the sensor from the tee.
3. Properly clean the pipe ends and tee sockets.
4. For the 228PV, solvent cement the pipe to the tee.
5. Reinstall sensor in tee as follows:
a. Align the small diameter blind hole on the top surface of the sensor with the tip of the flow arrow on the tee.
b. Carefully press the sensor straight into the tee.
c. Install the cotter ring.
6. Remove the wireless transmitter cap from the wireless transmitter body by unscrewing it in a counterclockwise direction.
7. Insert the wireless transmitter body through a minimum 1.625 inch (41 mm) hole in the valve box cover, maximum hole
size 2.5 inches (64 mm).
8. Screw the wireless transmitter cap hand tight to the wireless transmitter body. Then screw the nut against the inside of the
valve box cover so the cap is tight.
Wireless
Transmitter
Threaded
Cap
Nut
Wireless
Transmitter
Threaded Cap
Nut
5.125 in. (130 mm)
0.5 in.(13 mm)
0.5 in.(13 mm)
Figure 4: ORION wireless transmitter with threaded cap removed Figure 5: ORION wireless transmitter installed in valve box cover
Wireless Receiver Mechanical Installation
The wireless receiver can be surface mounted onto a panel or attached to DIN rails using adapter clips.
RF RCV
LED
BadgerMeter Inc.
Power In
AC L /DC
AC C /DC
D.I.C.
Comm Port
Antenna
(50 ohms)
Made in USA
+
-
PO
-
+
PO
Pulse Output
Output LED
Model 350R
S/N 350R-
1.60in.
(40.6mm)
3.65in.
(92.7mm)
2.95in.
(74.9mm)
.88in.
(22mm)
.60in.
(15mm)
Figure 6: ORION wireless receiver dimensions

Installation
Page 7March 2017 SEN-UM-01662-EN-05
Location
Although the wireless receiver is encapsulated, all wiring connections are made to exposed terminals. The unit should be
protected from weather and moisture in accordance with electrical codes and standard trade practices. In any mounting
arrangement, the primary concerns are ease of wiring and attachment of the programming cable.
The unit generates very little heat so no consideration needs to be given to cooling or ventilation.
The ideal receiver location is within clear line-of-sight of the flow sensor. However, this is rarely possible, with the line-of-sight
hindered by obstructions such as trees and vegetation, buildings and other structures, vehicles, and uneven terrain.
Surface Mount Installation
The wireless receiver can be mounted to the surface of any panel using double-sided adhesive tape, or by attaching fasteners
through the holes in the mounting flanges of the unit.
DIN Rail Mounting
Optional clips snap onto the mounting flanges, allowing the wireless receiver to be attached to DIN 15, 32, 35 mm DIN
rail systems.
Antenna Installation
The ORION RF receiver requires an external antenna to communicate with the RF transmitter. The antenna is typically
mounted directly to a customer-supplied enclosure that houses the RF receiver. The antenna can also be installed remotely
from the enclosure to be within a clear line-of-sight of the RF transmitter.
Antenna Kits
Antenna kits are an optional accessory and can be ordered by specifying the appropriate model number from the “” on page
3. Badger Meter offers two antenna kits: the A355LP low profile antenna kit and the A355 whip style antenna kit.
• The A355LP kit includes a low profile antenna and antenna cable with mounting hardware. The more durable, low profile
antenna is 2.3 inches (58 mm) in height and designed to operate in a frequency bandwidth of 902…928 MHz with a gain
of 3 dB.
• The A355 kit includes a whip style antenna, an antenna cable, mounting hardware, and 90 degree BNC adaptor. The
half-wave, whip style antenna is 8 inches (203 mm) in height and designed to operate in a frequency band of 902…970
MHz with a gain of 2.5 dB.
Both kits are supplied with an RG58C/U type
antenna cable.
Optional equipment and accessories
offered with the 228PV wireless system
can be ordered by specifying the
appropriate model number from the
Ordering Matrix shown here.
Figure 7: Ordering Matrix
28 PV 00 0 W - 1 2 1 1
STYLE
Tee Mounted Insert Sensor 28
MATERIAL
PVC (1.5", 2", 3", 4" Sch 80 only) PV
SIZE
1.5" 15
2" 20
3" 30
4" 40
ELECTRONICS HOUSING
PPS 0
ELECTRONICS
Wireless - Scaled pulse output W
Wireless - Frequency output U
O-RING
EPDM (STANDARD) 1
SHAFT
Tungsten Carbide (STANDARD) 2
IMPELLER
Stainless Steel Only 3
BEARING
UHMWPE (STANDARD) 1

Installation
Page 8 March 2017SEN-UM-01662-EN-05
See Figure 8 and Figure 9 for suggested antenna installation, mounting hole sizes, and component part numbers.
OTE:N Antenna cable lengths of more than 3 feet will negatively affect signal strength. Antennas operate more effectively
when well grounded (with a 3 inch (76 mm) diameter ground plane). Use the grounding washers included in both
installation kits.
P/N: 820060-0001
LOW PROFILE ANTENNA PORTABLE
P/N: 840030-0001
ANTENNA CABLE W/BNC CONNECTOR
AND BRASS MOUNTING HARDWARE
LOW PROFILE ANTENNA MOUNTING HOLE = Ø 3/4"
350 RECEIVER ASSEMBLY
ENCLOSURE
(SUPPLIED BY CUSTOMER)
P/N: 820057-0001
8" WHIP STYLE ANTENNAPORTABLE
P/N: 820058-0001
MOUNTING HARDWARE W/BNC CONNECTORS F/F
MOUNTING HOLE: Ø1/2"
P/N: 820056-0001
ANTENNA CABLE W/BNC CONNECTORS M/M
P/N: 820059-0001
90° BNC ADAPTOR
ENCLOSURE
(SUPPLIED BY CUSTOMER)
350 RECEIVER ASSEMBLY
Figure 8: A355LP antenna kit Figure 9: A355 antenna kit
Wireless Receiver Electrical Installation
Per standard wiring practices, turn off the power before making any wire connections. The terminal strips have removable
plug-in connectors to make wiring easier.
3/32 in. Flathead
Screwdriver
Series 300
Connector
Wire
RF RCV
LED
BadgerMeter Inc.
Power In
AC L /DC
AC C /DC
D.I.C.
Comm Port
Antenna
(50 ohms)
Made in USA
+
-
PO
-
+
PO
Pulse Output
Output LED
Model350R
S/N 350R-
12-24V DC
or 12 -24VAC
Po wer Su pply
+
-
36 VD C Max
Co unter with
Intern al
Pu ll-up
Re si st or
+
-
Figure 10: Typical series 300 removable connector wiring, side view Figure 11: Sample ORION wireless receiver electrical wiring
OTE:N Follow these steps and see Figure 11 for terminal connections and wiring example.
1. Connect DC power supply positive (+) or AC line to the wireless receiver terminal marked AC L/DC (+).
2. Connect DC power supply negative (–) or AC common to the wireless receiver terminal marked AC C/DC (–).
3. Connect pulse (+) of a pulse input device to the wireless receiver terminal marked PO (+).
4. Connect pulse (–) of a pulse input device to the wireless receiver terminal marked PO (–).
5. Connect 50 Ω (Ohm) antenna to BNC antenna connector of the wireless receiver.

Theory of Operation
Page 9March 2017 SEN-UM-01662-EN-05
THEORY OF OPERATION
The ORION RF receiver can be located up to 500 feet away from the RF transmitter and must be powered with
12…24V AC/DC. A BNC connector is provided on the RF receiver to accept a 50 Ohm, half-wave antenna.
There are two red LEDs on the receiver.
• The“RF RCV” LED in the middle of the unit flashes each time it receives an updated total from the RF transmitter,
approximately every four seconds.
• The“OUTPUT” LED flashes each time an output pulse is generated by the receiver.
After each update, the RF receiver compares this updated total with the last one received. The difference is the total volume
in gallons that has passed through the sensor for the period in question. The RF receiver then generates a continuous burst
of output pulses with a duty cycle of 50%. These pulses can be scaled using the DIC Com Port and Badger Meter software to
represent the desired volume unit, number of volume units per pulse, and pulse width that best fit the application. Default
values for these settings are gallons, 10 gallons per pulse, and 50 milliseconds, respectively.
If the combination of volume units, volume units per pulse, and pulse width selected prevents the number of corresponding
output pulses from being generated in the 4…5 second update window, the RF receiver will simply delay the next update
until the pulse string has been completed.
Sensor Model 228PV200W-1231-000
Line Size 2 inches
Gallons per Integer Output from Transmitter 1 (default)
Volume Unit Selected in Receiver liters
Volume Units per Pulse Output from Receiver 10
Pulse Width 50 milliseconds
If 10 gallons pass through the sensor in a given 4 second window, 10 integer values are sent by the transmitter in the next
update, representing a volume of 10 gallons. The receiver, in turn, converts the 10 gallons into 37.8 liters and generates three
output pulses, representing a volume of 30 liters. Because partial counts exist in both the sensor and receiver, the remaining
7.8 liters are sent as part of the next update from the sensor.
OTE:N The Badger Meter Model A301W cable works with all Series 300 products. However, the older version of the cable
(A300) does not have sufficient bandwidth to work with this receiver.
PROGRAMMING
No programming is required for the frequency output version of this system (electronics order code “U”). Simply enter the K
and Offset information from the table below into the input device:
Model No. K Offset
228PV150U-xxxx-xxx 0.550342 -5.683758
228PV200U-xxxx-xxx 1.1544738 -1.3758585
228PV300U-xxxx-xxx 3.358104 -1.668902
228PV400U-xxxx-xxx 5.97996 0.440556
For the scaled pulse output version of this system, use the software installation and programming instructions that begin on
the next page.

Programming
Page 10 March 2017SEN-UM-01662-EN-05
Programming Software Installation
Communications Cable Wiring
To change parameters in the wireless receiver or sensor, a Badger Meter Model A301W Programming Kit (consisting of a
custom cable, IR dongle, and software) and a computer (PC) running Windows® 7 or XP is required. In order to program, the
wireless receiver must be connected to power, and the communications cable must be connected to both the D.I.C. Comm
port and an available DB9 Comm port on the PC.
CDROM Installation
Insert the software CD into a CDROM drive on the PC. The software installation should start automatically. Follow the
instructions from the installation Wizard to complete installation. When installation is complete, go to Windows Start\
Programs\Badger Meter Inc., and select Model 350W to start the programming software application.
Web Installation
Badger Meter provides free programming software updates via the Internet for all field programmable devices. The
installation software can be found under Support & Resources> Software on the website at www.badgermeter.com.
Wireless Receiver Programming
To change the settings of the wireless receiver, use the programming software to enter new values as outlined here.
1. Connect the PC with the installed software to the wireless receiver using the Model A301W IR communications cable.
• Plug the Model A301W cable in to the socket labeled“D.I.C. Comm Port”, taking care to properly align the tab on the
plug and socket to maintain polarity.
• Then plug the DB9 connector of the Model A301W communications cable to an available Com port on the PC. If a DB9
port is not available, use a (customer supplied) USB-to-DB9 adapter (example, IOGEAR GUC232A).
2. Connect the wireless receiver to a power supply.
3. Start the software.
4. Select Device>350 from the main menu. Then select Pulse Receiver from the Device Type drop-down menu.
Figure 12: Select Device and Device Type
5. Select Configuration> Set Comm Port from the main menu to open the Comm Settings window. Select the appropriate
Comm port for the A301W communications cable. Then click OK. The Comm Settings window closes.
Figure 13: Comm settings

Programming
Page 11March 2017 SEN-UM-01662-EN-05
6. Click Poll Now to update the current values.
7. Select Conguration> Parameters to open the Parameters screen. You can also select the Parameters button. See
Figure 14.
Figure 14: Select Parameters
8. Program the wireless receiver using the Parameters screen in Figure 15 as a reference.
a. Serial Number: Enter the serial number of the
wireless receiver. ‘
b. Volume Unit: Select the desired volume unit for scaled
output pulses.
c. 1 Pulse: Enter the desired volume per scaled
output pulse.
d. Pulse Width: Enter the scaled output pulse width.
OTE:N The default pulse width is 50 milliseconds.
Minor variation in pulse width may be
required, depending on controller interface.
e. Lost Signal Recovery: Configure this section
depending on the application requirements. If
checked, the data accumulated during a lost signal
period will be recovered. See the instructions on the
screen for more information.
f. Send: Click to calibrate the wireless receiver with the
information that was entered.
g. Refresh: Click to see the current programming.
h. Defaults: Click to enter the factory default
programming.
OTE:N Selecting Defaults overwrites all settings.
i. Exit: Click to exit and close the Parameters screen.
Figure 15: Receiver parameters
9. Click the Xin the top right corner of the screen to exit the programming software.

Programming
Page 12 March 2017SEN-UM-01662-EN-05
Wireless Flow Sensor Programming
The wireless flow sensor is factory programmed based on the line size for your application, using the default settings given in
the table below (based on 15 fps flow velocities).
Model No. K Offset
Recommended
Volume / Pulse
Output (gallons)
Minimum…Maximum
Flow Range (gpm)
228PV150W-xxxx-xxx 0.275171 -11.367570 1 6…95
228PV200W-xxxx-xxx 0.577369 -2.751717 1 10…156
228PV300W-xxxx-xxx 1.679052 -3.337804 10 23…345
228PV400W-xxxx-xxx 2.989980 0.881112 10 39…595
These factory settings consist of the Kand Offset values and Gallons per Pulse Output.
OTE:N The Kand Offset values, empirically derived from flow tests using NIST traceable instruments, are used in the
calibration equation (Frequency = GPM/K – Offset) to calculate sensor frequency at any flow rate within its
operational range. Factory settings for Kand Offset values are normally changed only when installing the sensor in
a different line size, or when custom values are required (example, non-standard piping). If custom values for Kand
Offset values are required, contact the factory for assistance. If no line size is specified at the time of order placement,
default values of 0.5 and 0, respectively, will be used for Kand Offset.
The value for Gallons per Pulse Output sets the system resolution. Lowering the factory default value for Gallons per Pulse
Output is not recommended because it will decrease transmitter battery life and can affect transmitter operation.
Badger Meter sensors will operate both above and below the suggested flow range for each tee size. Test results have shown,
however, that the highest accuracy and best repeatability are achieved in the suggested flow range.

Programming
Page 13March 2017 SEN-UM-01662-EN-05
Programming New Flow Sensor Values
To change the settings of the wireless sensor, use the programming software to enter new values as outlined here.
1. Start the programming software.
2. Connect the infrared cable (IR cable) to the computer.
3. Select Device>350 from the main menu. Then select Sensor from the Device Type drop-down menu.
Figure 16: Select Device and Device Type
4. Select Configuration> Set Comm Port from the main menu to open the Comm Settings window. Select the appropriate
Comm port for the IR cable. Then click OK. The Comm Settings window closes.
Figure 17: Comm settings
5. Align the IR cable with the IR LED port of the sensor and click Poll Now to update the current values.
OTE:N Hold the IR cable no more then 2 inches from the top of the sensor.
Figure 18: Poll Now

Programming
Page 14 March 2017SEN-UM-01662-EN-05
6. Select Conguration> Parameters to open the Parameters screen. You can also select the Parameters button.
See Figure 19.
Figure 19: Select Parameters
7. Program the wireless flow sensor using the Parameters screen in Figure 20 as a reference.
a. Pipe Size: Select sensor size from the drop-down
menu. If custom K and Offset values are required,
select Other (Unlisted).
b. Sensor Configuration: The K and Offset values will
automatically display in these fields for the flow
sensor size selected in Pipe Size. If Other (Unlisted)
was selected, enter the desired values in each field.
c. Rate Unit: Select the desired unit for flow rate display.
d. Pulse Output Control: Enter the desired volume per
output pulse.
MPORTANTI
Align the IR cable with the IR LED port of the sensor before
selecting Send, Refresh or Defaults.
e. Send: Click to calibrate the wireless receiver with the
information you entered.
f. Refresh: Click to see the current programming.
g. Defaults: Click to enter the factory default
programming.
OTE:N Selecting Defaults overwrites all settings.
h. Exit: Click to exit and close the Parameters screen.
Figure 20: Flow sensor parameters
8. Click the Xin the top right corner of the screen to exit the programming software.

Specications
Page 15March 2017 SEN-UM-01662-EN-05
SPECIFICATIONS
Wetted Materials (Except Tee) Refer to the Ordering Matrix
Tee for 228PV
Schedule 80 PVC per ASTM D-2462 and D-2467. Virgin, unplasticized PVC resin, Type
1 cell classification 12454-B. Fittings and solvent carry approval for potable water by
NSF and IAMPO.
Power Requirements
Flow sensor-lithium battery powered (typical battery life > 5yr)
ORION transmitter, battery powered (typical battery life > 10yr)
ORION receiver, external power 12…24V AC/DC
Current
Draw
36 mA @ 12V DC
16 mA @ 24V DC
40 mA rms @ 12V AC rms
30 mA rms @ 24V AC rms
Recommended Flow Range 5…20 fps
Extended Flow Range 1 to 20 fps
Accuracy Standard ± 2% of rate of full scale over recommended design flow range
Repeatability ± 0.5% of full scale over recommended design flow range
Maximum Operating Temperature 32…150° F (0…65° C)
CSA-approved Temperature Rating 140° F (60° C)
Sensor Pressure Drop 0.5 psi or less at 10 fps for all pipe sizes 1.5 in. (38 mm) diameter and larger
Programming
Sensor and transmitter programming is accomplished using PC software via an
infrared (IR) link
ORION RF receiver programming is accomplished using PC software via the
A301W-20 connector cable
Flow Sensor Programmable
Parameters
K & Offset dependent upon pipe size
Flow units (gpm, gph, lps, lpm, ft3/sec, ft3/min, m3/sec, m3/min)
Scaled pulse output (units/pulse)
ORION Receiver
Programmable Parameters
Serial number (unique to the ORION Transmitter ID)
Volume units (gallons, ft3, m3, liters)
Scaled pulse output (units/pulse)
Scaled pulse output (pulse width)
Performance Range 500 ft line of sight

www.badgermeter.com
ORION is a registered trademark of Badger Meter, Inc. Other trademarks appearing in this document are the property of their respective entities. Due to continuous research,
product improvements and enhancements, Badger Meter reserves the right to change product or system specications without notice, except to the extent an outstanding
contractual obligation exists. © 2017 Badger Meter, Inc. All rights reserved.
Control. Manage. Optimize.
Flow Sensors, Wireless Flow Sensor System
The Americas | Badger Meter | 4545 West Brown Deer Rd | PO Box 245036 | Milwaukee, WI 53224-9536 | 800-876-3837 | 414-355-0400
México | Badger Meter de las Americas, S.A. de C.V. | Pedro Luis Ogazón N°32 | Esq. Angelina N°24 | Colonia Guadalupe Inn | CP 01050 | México, DF | México | [phone]
Europe, Eastern Europe Branch Oce (for Poland, Latvia, Lithuania, Estonia, Ukraine, Belarus) | Badger Meter Europe | ul. Korfantego 6 | 44-193 Knurów | Poland | [phone]
Europe, Middle East and Africa | Badger Meter Europa GmbH | Nurtinger Str 76 | 72639 Neuen | Germany | [phone]
Europe, Middle East Branch Oce | Badger Meter Europe | PO Box 341442 | Dubai Silicon Oasis, Head Quarter Building, Wing C, Oce #C209 | Dubai / UAE | [phone]
Slovakia | Badger Meter Slovakia s.r.o. | Racianska 109/B | 831 02 Bratislava, Slovakia | [phone]
Asia Pacic | Badger Meter | 80 Marine Parade Rd | 21-06 Parkway Parade | Singapore 449269 | [phone]
China | Badger Meter | 7-1202 | 99 Hangzhong Road | Minhang District | Shanghai | China 201101 | [phone]
Switzerland | Badger Meter Swiss AG | Mittelholzerstrasse 8 | 3006 Bern | Switzerland | [phone] Legacy Document Number: 880024