Balkene Home Ashville Chat Set 63742 User manual

Ashville Chat Set
Item#: 63742
SAVE THESE
INSTRUCTIONS FOR
FUTURE REFERENCE.
ATTACH YOUR
RECEIPT HERE
Keep a copy of your proof of
purchase or order confirmation
which will be needed if you need to
contact us about warranty coverage.
Purchase Date:
Questions, problems, missing parts?
Before returning to your retailer, our Florida-based customer service team is available:
Call toll-free 9 a.m. – 9 p.m., EST
Email
Live chat
(866)866) 985-7877
[email protected]
www.balkenehome.com 9 a.m. – 6 p.m., EST, Monday - Friday
03242021

Contact us for assistance: [phone] | www.balkenehome.com 2
BEFORE YOU BEGIN
Before beginning assembly, make sure all parts are present. Compare parts received with the parts list. If any
part is missing or damaged, do NOT attempt to assemble the product. Please read and understand this entire
manual before attempting to assemble, operate or install this product. If you have any questions regarding the
product, please contact Customer Service.
GENERAL INFORMATION
Your new patio set is made from the finest materials available. It should provide years of enjoyment with
minimal care.
Keep your patio set clean. For best results, clean with a soft, damp cloth. You may use a standard glass cleaning
spray to clean the glass tabletop. If you use furniture covers, always make sure the patio set is clean and
completely dry before covering, as mold may form in dark, wet places. Remove cushions prior to covering and
store them in a dry, temperature controlled place. Check the hardware on your patio set regularly to make sure
it is secure.
The weight limit is 220 lb/100kg per chair, 440 lb/200kg total for sofa.
SAFETY INFORMATION
WARNING
Do not stand or allow children to stand on the assembled product. Ensure hardware is securely in place.
Perform periodic checks to make sure the connections are secure and adjust if needed. The glass tabletop is
tempered for strength but may break or chip if dropped, struck sharply, or otherwise abused. Do not sit or
stand on the glass tabletop, and take reasonable precautions to avoid injury in the event of glass breakage.
CAUTION
Read all instructions before beginning assembly. Failure to do so may result in faulty assembly and potential
injury. Assemble the item on a soft, non-abrasive surface such as carpet or cardboard to avoid damaging the
item.
INFORMATION

PART DESCRIPTION QUANTITY
(per chair)
ASeat Panel 1
BBackrest 1
CLeft Panel* 1
DRight Panel* 1
ESeat Cushion 1
G
M6x40 Bolt
Qty: 11
Hex Wrench
H
Washer
HARDWARE CONTENTS
D
E
B
A
C
Contact us for assistance: [phone] | www.balkenehome.com
*When facing the front of the chair
3
3
Assemble in a clear area on a spacious, nonabrasive surface such as a carpet or blanket. Wait to fully tighten hardware
until final step. Do not over-tighten hardware.
PACKAGE CONTENTS: CHAIRS
Qty: 11
(per chair)

1
Locate the Backrest B and Seat Panel A. Place a
Washer G on a Bolt F. Align the panels as shown.
Insert the Bolt with Washer through the eyelet in the
underside of the Seat Panel and into the hole in the
middle of the bottom of the Backrest.
Tighten using the Hex Wrench, but do not over-tighten.
Hardware Used: F Bolt (M6x40) x1
G Washer x1
2
Attach the Left and Right Panels C/D to the
assembled seat: Place a Washer G on each of 6
Bolts F. Align the eyelets on the Left Panel with the
holes in the edge of the Seat Panel as shown, then
insert a Bolt with Washer into each of the 3 aligned
sets of eyelets (1 behind the front panel of the seat,
2 along the side of the seat). Gently tighten using
Hex Wrench without fully tightening. Repeat to
attach the Right Panel.
B
Hardware Used:
3
Secure the Side Panels to the Backrest B. Place a
Washer H on each of 4 Bolts G. Insert a Bolt with
Washer through each of the 4 aligned sets of eyelets.
Hardware Used:
F Bolt (M6x40) x6
G Washer x6
Contact us for assistance: [phone] | www.balkenehome.com
x 6
x 4
F Bolt (M6x40) x4
G Washer x4
F
G
GF
4
ASSEMBLY: CHAIRS
A
F
G
C
D
R1
R1
R1
R1
B

4
Turn assembled chair upright on a flat, level surface to
ensure that it sits squarely and level on the ground.
Adjust fastenings if needed, then firmly tighten all Bolts
installed in Steps 1-3.
Place the Seat Cushion E in the seat.
Repeat Steps 1-4 to assemble second chair.
Your Ashville Chairs are fully assembled!
Contact us for assistance: [phone] | www.balkenehome.com
E
5
ASSEMBLY: CHAIRS

QuanTiTY
E
B
A
Contact us for assistance: [phone] | www.balkenehome.com
*When facing the front of the sofa
6
Assemble in a clear area on a spacious, nonabrasive surface such as a carpet or blanket. Wait to fully tighten hardware
until final step. Do not over-tighten hardware.
PACKAGE CONTENTS: SOFA BENCH
D
C
PART DESCRIPTION
ASeat Panel 1
BBackrest 1
CLeft Panel* 1
DRight Panel* 1
ESeat Cushion 1
G
M6x40 Bolt
Qty: 12
Hex Wrench
H
Washer
Qty: 12
HARDWARE CONTENTS

Contact us for assistance: [phone] | www.balkenehome.com
7
ASSEMBLY: SOFA BENCH
1
Locate the Backrest B and Seat Panel A. Place a
Washer H on each of 2 Bolts G. Align the panels as
shown. Insert the Bolts with Washers through the
eyelets in the underside of the Seat Panel and into
the holes at the bottom of the front of the Backrest.
Tighten using the Hex Wrench, but do not over-tighten.
Hardware Used: G Bolt (M6x40) x2
H Washer x2
A
B
G
H
2
Attach the Left and Right Panels C/D to the
assembled seat: Place a Washer G on each of 6
Bolts F. Align the eyelets on the Left Panel with the
holes in the edge of the Seat Panel as shown, then
insert a Bolt with Washer into each of the 3 aligned
sets of eyelets (1 behind the front panel of the seat,
2 along the side of the seat). Gently tighten using
Hex Wrench without fully tightening. Repeat to
attach the Right Panel.
Hardware Used: G Bolt (M6x40) x6
H Washer x6
D
C
G+H
3
Secure the Side Panels to the Backrest B. Place a
Washer H on each of 4 Bolts G. Insert a Bolt with
Washer through each of the 4 aligned sets of eyelets.
hardware used: G Bolt (M6x40) x4
H Washer x4
R1
R1
R1
R1
G+H G+H
B
A
CD
HG

4
Contact us for assistance: [phone] | www.balkenehome.com
8
ensure that it sits squarely and level on the ground.
Place assembled sofa upright on a flat, level surface to
Adjust fastenings if needed, then firmly tighten all Bolts.
Place the Seat Cushion E in the seat.
Your Ashville Sofa is fully assembled!
E
ASSEMBLY: SOFA BENCH

PART DESCRIPTION QUANTITY
ATable Frame 1
BShelf 1
CLeg 4
DGlass Tabletop 1
E
Hex Wrench
F
Washer
Qty: 12
HARDWARE CONTENTS
D
B
A
C
M6x20 Bolt
Qty: 12
Assemble in a clear area on a spacious, nonabrasive surface such as a carpet or blanket. Wait to fully tighten hardware
until final step. Do not over-tighten hardware.
Contact us for assistance: [phone] | www.balkenehome.com
9
PACKAGE CONTENTS: TABLE

1
2
Place the Table Frame B upside-down on a protected
surface (Bolt holes will be visible near each corner). Place
a Washer F on each of 8 Bolts E.
Position a Leg C at the corner of the Table Frame as
shown, aligning the eyelets in the top plate of the Leg with
the holes in the Table Frame. Insert a Bolt with Washer
into each of the the aligned sets of eyelets.
Repeat to install remaining 3 Legs.
Tighten Bolts with the Hex Key, but do not over-tighten.
Note: for illustration purposes, the table is shown
upside-down, but this step may be easier to complete
with the table on its side or upright. Place a Washer F
on each of 4 Bolts E. Position the Shelf between the
installed Legs resting against the lower brackets of each
Leg, then insert a Bolt with Washer through each
bracket eyelet and into the threaded holes in the
bottom of the Shelf.
Tighten Bolts with the Hex Key, but do not over-tighten.
hardware used: E Bolt (M6x20) x4
F Washer x4
hardware used: E Bolt (M6x20) x8
F Washer x8
Your Ashville Table is fully assembled!
Contact us for assistance: [phone] | www.balkenehome.com
10
x4
Place assembled table upright on a flat, level surface to
ensure that it sits squarely and level on the ground.
Adjust connections if needed, then firmly tighten all
Bolts.
Carefully place the Glass Tabletop D on the assembled
Table Frame.
3
E
F
D
ASSEMBLY: TABLE
C
C
A
E
F
x8
A
B