Balkene Home Jareth 63177 User manual

Jareth Patio Set
Item#: 63177
SAVE THESE
INSTRUCTIONS FOR
FUTURE REFERENCE.
ATTACH YOUR
RECEIPT HERE
Keep a copy of your proof of
purchase or order confirmation
which will be needed if you need to
contact us about warranty coverage.
Purchase Date:
Questions, problems, missing parts?
Before returning to your retailer, our exceptional customer service is available.
Call toll-free 9 a.m. – 9 p.m., EST
Email
Live chat
(866)866) 985-7877
[email protected]
www.balkenehome.com 9 a.m. – 6 p.m., EST, Monday - Friday
05132020

Contact us for assistance: [phone] | www.wtliving.com 2
BEFORE YOU BEGIN
Before beginning assembly, make sure all parts are present. Compare parts received with the parts list. If any part
is missing or damaged, do NOT attempt to assemble the product. Please read and understand this entire manual
before attempting to assemble, operate or install this product. If you have any questions regarding the product,
please contact Customer Service.
GENERAL INFORMATION
Your new Jareth Patio Set is made from the finest materials available. It should provide years of enjoyment with
minimal care.
Keep your Jareth Patio Set clean. For best results, clean with a soft, damp cloth. You may use a standard glass
cleaning spray to clean the glass tabletop. If you use furniture covers, always make sure the Jareth Patio Set is
clean and completely dry before covering, as mold may form in dark, wet places. Remove cushions prior to
covering and store them in a dry, temperature controlled place. Check the hardware on your Jareth Patio Set
regularly to make sure it is secure.
The weight limit is 220 lb/100kg per chair, 440 lb/200kg total for sofa.
SAFETY INFORMATION
WARNING
Do not stand or allow children to stand on the assembled product. Ensure hardware is securely in place. Perform
periodic checks to make sure the connections are secure and adjust if needed. The glass tabletop is tempered for
strength but may break or chip if dropped, struck sharply, or otherwise abused. Do not sit or stand on the glass
tabletop, and take reasonable precautions to avoid injury in the event of glass breakage.
CAUTION
Read all instructions before beginning assembly. Failure to do so may result in faulty assembly and potential
injury. Assemble the item on a soft, non-abrasive surface such as carpet or cardboard to avoid damaging the
item.
INFORMATION

PART DESCRIPTION QUANTITY
ALeft* Side Panel 1
BRight* Side Panel 1
CSeat Panel 1
DBack Panel 1
ESeat Cushion 1
FG
M6x35Bolt
Qty: 4
Hex Key
H
Washer
Qty: 100
HARDWARE CONTENTS
D
E
B
A
C
M6x25Bolt
Qty: 6
Contact us for assistance: [phone] | www.balkenehome.com
*When facing the front of the chair
3
3
Assemble in a clear area on a spacious, nonabrasive surface such as a carpet or blanket. Wait to fully tighten hardware
until final step. Do not over-tighten hardware.
PACKAGE CONTENTS: CHAIRS

1
Locate the Right Side Panel B and Seat Panel C. Place a
Washer H on each of 3 Bolts F. Align the panels as
shown. Insert each Bolt with Washer through the eyelets
in the Seat Panel and into the holes in the edge of the
Right Side Panel.
Tighten using the Hex Key, but do not over-tighten.
Hardware Used: F Bolt (M6x25) x3
H Washer x3
2
Attach the Back Panel D to the Right Side Panel B:
Place a Washer H on each of 2 Bolts G. Align the
eyelets on the Back Panel with the holes in the Right
Side Panel as shown, then insert a Bolt with Washer
into each of the 2 aligned sets of eyelets.
Tighten using the Hex Key, but do not over-tighten.
B
C
Hardware Used:
3 Locate the Left Side Panel D. Place a Washer H on
each of 2 Bolts G. Place the partially-assembled chair
on the Left Side Panel as shown. Align the eyelets on the
Back Panel with the holes in the Left Side Panel and
insert a Bolt with Washer through each of the 2 aligned
sets of eyelets.
Tighten using the Hex Key, but do not over-tighten.
Hardware Used:
G Bolt (M6x35) x2
H Washer x2
Contact us for assistance: [phone] | www.balkenehome.com
x 3
F
H
x 2
x 2
G Bolt (M6x35) x2
H Washer x2
B
C
D
A
G
H
G
H
DC
B
4
ASSEMBLY: CHAIRS

4
5
Place a Washer H on each of 3 Bolts F. To attach the
Left Side Panel C to the Seat Panel B, insert a Bolt
with Washer into the 3 aligned sets of eyelets.
Tighten Bolts using the Hex Key, but do not over-
tighten.
Turn assembled chair upright on a flat, level surface to
ensure that it sits squarely and level on the ground.
Adjust fastenings if needed, then firmly tighten all Bolts.
Place the Seat Cushion in the seat.
Hardware Used: F Bolt (M6x25) x3
H Washer x3
Your Jareth Chair is fully assembled!
Repeat these steps to assemble the second chair.
Contact us for assistance: [phone] | www.balkenehome.com
x 3
E
C D
A
B
5
F
H
ASSEMBLY: CHAIRS

PART DESCRIPTION QUANTITY
ALeft* Side Panel 1
BRight* Side Panel 1
CSeat Panel 1
DBack Panel 1
ESeat Cushion 1
FG
M6x35Bolt
Qty: 44
Hex Key
H
Washer
Qty: 12
HARDWARE CONTENTS
D
E
B
A
C
M6x25Bolt
Qty: 8
Contact us for assistance: [phone] | www.balkenehome.com
*When facing the front of the sofa
6
Assemble in a clear area on a spacious, nonabrasive surface such as a carpet or blanket. Wait to fully tighten hardware
until final step. Do not over-tighten hardware.
PACKAGE CONTENTS: BENCH

Contact us for assistance: [phone] | www.balkenehome.com
7
1
Locate the Right Side Panel B and Seat Panel C. Place a
Washer H on each of 3 Bolts F. Align the panels as
shown. Insert each Bolt with Washer through the eyelets
in the Seat Panel and into the holes in the edge of the
Right Side Panel.
Tighten using the Hex Key, but do not over-tighten.
Hardware Used: F Bolt (M6x25) x3
H Washer x3
2
Hardware Used:
3
Fasten the Back Panel D to the Seat Panel C:
Place a Washer H on each of 2 Bolts F. Insert each
Bolt with Washer into one of the 2 aligned sets of
eyelets on the underside of the Seat Panel.
Tighten using the Hex Key, but do not over-tighten.
Hardware Used:
G Bolt (M6x35) x2
H Washer x2
F Bolt (M6x25) x2
H Washer x2
Attach the Back Panel D to the Right Side Panel B:
Place a Washer H on each of 2 Bolts G. Align the
eyelets on the Back Panel with the holes in the Right
Side Panel as shown, then insert a Bolt with Washer
into each of the 2 aligned sets of eyelets.
Tighten using the Hex Key, but do not over-tighten.
x 3
x 2
x 2
F
H
H
G
HF
C
B
B
D C
C
D
B
ASSEMBLY: BENCH

4
5
hardware used: F Bolt (M6x25) x3
H Washer x3
hardware used: G Bolt (M6x35) x2
H Washer x2
Contact us for assistance: [phone] | www.balkenehome.com
8
x 2
Locate the Left Side Panel D. Place a Washer H on
each of 2 Bolts G. Place the partially-assembled sofa
on the Left Side Panel as shown. Align the eyelets on
the edge of the Back Panel with the holes in the Left
Side Panel and insert a Bolt with Washer through
each of the 2 aligned sets of eyelets.
Tighten Bolts using the Hex Key, but do not over-
tighten.
Place a Washer H on each of 3 Bolts F. To attach the
Left Side Panel C to the Seat Panel B, insert a Bolt
with Washer into the 3 aligned sets of eyelets on the
underside of the Seat Panel.
Tighten Bolts using the Hex Key, but do not over-
tighten.
x 3
6Turn assembled sofa upright on a flat, level surface to
ensure that it sits squarely and level on the ground.
Adjust fastenings if needed, then firmly tighten all Bolts.
Place the Seat Cushion E in the seat.
Your Jareth Sofa is fully assembled!
B
C D
A
G
H
C
A
D
B
E
ASSEMBLY: BENCH

PART DESCRIPTION QUANTITY
AGlass Tabletop 1
BTable Frame 1
CLeg 4
DShelf 1
E
Hex Key
F
Washer
Qty: 12
HARDWARE CONTENTS
D
B
A
C
M6x15 Bolt
Qty: 12
Assemble in a clear area on a spacious, nonabrasive surface such as a carpet or blanket. Wait to fully tighten hardware
until final step. Do not over-tighten hardware.
Contact us for assistance: [phone] | www.balkenehome.com
9
PACKAGE CONTENTS: TABLE

1
2
Place the Table Frame B upside-down on a protected
surface (Bolt holes will be visible at each corner). Place a
Washer F on each of 8 Bolts E.
Position a Leg C at the corner of the Table Frame as
shown, aligning the eyelets in the top plate of the Leg
with the threaded holes in the Table Frame. Insert a Bolt
with Washer into each of the the aligned sets of eyelets.
Repeat to install remaining 3 Legs.
Tighten Bolts with the Hex Key, but do not over-tighten.
Place a Washer F on each of 4 Bolts E. Position the
Shelf between the installed Legs as shown, then insert a
Bolt with Washer through each bracket eyelet and into
the threaded holes in the bottom of the Shelf.
Tighten Bolts with the Hex Key, but do not over-tighten.
hardware used: E Bolt (M6x15) x4
F Washer x4
hardware used: E Bolt (M6x15) x8
F Washer x8
Your Jareth Table is fully assembled!
Contact us for assistance: [phone] | www.balkenehome.com
10
x 4
x 4
Turn assembled table upright on a flat, level surface to
ensure that it sits squarely and level on the ground.
Adjust fastenings if needed, then firmly tighten all Bolts.
Carefully place the Glass Tabletop A on the Table
Frame.
3
D
B
C
C C
C
E
F
E
F
A
ASSEMBLY: TABLE

LIMITED WARRANTY
Customers in the Contiguous US
With proof of purchase from an authorized retailer, this product is warranted
for a period of 1 year from original purchase date against defects in materials
and workmanship under normal use. This warranty does NOT cover normal
wear/weathering, exposure to water, freezing temperatures, oils, fluids, or
chemicals OR use in a commercial context if the unit is not designated as a
commercial model. At Well Traveled Living’s sole discretion, products under
warranty will be repaired and/or replaced at no charge to the customer.
Returns sent back to Well Traveled Living must be sent via prepaid freight in
the original retail packaging.
For warranty service, contact Balkene Home/Well Traveled Living at the
address, phone numbers or website and email listed in this owner’s manual.
Be sure to have your sales receipt, date of purchase and catalogue/model
numbers available when calling. All warranty service will be coordinated by
Well Traveled Living's Amelia Island, Florida service center. This warranty is
extended only to the original owner. Proof of purchase will be required before
warranty service is rendered. The sales receipt is the only valid proof of
purchase. This warranty only covers failures due to defects in materials or
workmanship which occur during normal use. Failures and/or damage which
result from accident, negligence, misuse, abuse, neglect, mishandling,
alteration or modification, failure to maintain, improper assembly or
maintenance, service by unauthorized agency or use of unauthorized
components or damage that is attributable to acts of God are NOT covered.
This limited warranty gives you specific legal rights and you may also have
other rights which vary from jurisdiction to jurisdiction. The provisions of the
United Nations Convention on Contracts for the Sales of Goods shall not apply
to this limited warranty or the sale of products covered by this limited
warranty.
• THERE ARE NO EXPRESS WARRANTIES EXCEPT AS
LISTED.
• PURCHASER ASSUMES ALL RISKS IN THE
ASSEMBLY AND OPERATION OF THIS UNIT.
• FAILURE TO FOLLOW WARNINGS AND
OPERATIONAL INSTRUCTIONS CONTAINED IN
THIS MANUAL CAN RESULT IN SEVERE PROPERTY
DAMAGE AND/OR PERSONAL INJURY.
• IN NO EVENT WILL WELL TRAVELED LIVING, OR
ITS DIRECTORS, OFFICERS OR AGENTS BE LIABLE
TO THE PURCHASER OR ANY THIRD PARTY,
WHETHER IN CONTRACT, IN TORT, OR ON ANY
OTHER BASIS, FOR ANY INDIRECT, SPECIAL,
PUNITIVE, EXEMPLARY, CONSEQUENTIAL, OR
INCIDENTAL LOSS, COST, OR DAMAGE ARISING
OUT OF OR IN CONNECTION WITH THE SALE,
MAINTENANCE, USE, OR INABILITY TO USE THE
PRODUCT, EVEN IF WELL TRAVELED LIVING OR
ITS DIRECTORS, OFFICERS OR AGENTS HAVE BEEN
ADVISED OF THE POSSIBILITY OF SUCH LOSSES,
COSTS OR DAMAGES, OR IF SUCH LOSSES, COSTS,
OR DAMAGES ARE FORESEEABLE. IN NO EVENT
WILL WELL TRAVELED LIVING, OR ITS OFFICERS,
DIRECTORS, OR AGENTS BE LIABLE FOR ANY
DIRECT LOSSES, COSTS OR DAMAGES THAT
EXCEED THE PURCHASE PRICE OF THE PRODUCT.
• SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO
THE PURCHASER.
Important Notice
Do NOT return to place of purchase—for customer service and warranty issues:
Call toll-free
Email
Live chat
[phone] 9 a.m. – 9 p.m., EST
[email protected]
balkenehome.com 9 a.m. - 6 p.m., EST, Monday - Friday
Distributed by:
Well Traveled Living
716 S 8th Street, Amelia Island, FL 32034
balkenehome.com
[email protected]
[phone]
Fire Sense®, Patio Sense,® Avalon Home,® Mojave Sun®, Vulcan®, Balkene Home® and Well Traveled Living® are registered trademarks of
Well Traveled Imports, Inc®. All assembly instruction presentations are the property of Well Traveled Imports, Inc.
® and are protected by
U.S. copyrights and trademarks. All rights reserved.
EXTEND YOUR WARRANTY
When you purchase a Fire Sense or Balkene Home product from any authorized retailer, you'll have peace
of mind in knowing that it comes with a one-year warranty. Extend your warranty for an additional year
when you review your item at balkenehome.com within 365 days of purchase.