Ballard Designs Grant Swing Arm Sconce User manual

PRODUCT NAME: Grant Swing Arm Sconce
ITEM NUMBER: LW612
ASSEMBLED DIMENSIONS: 17.5”H x 25”W x 3.25”D
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
IMPORTANT SAFETY INSTRUCTIONS:
-This Lamp has a polarized plug (one blade is wider than the other) as a feature to reduce the risk
of electric shock. This plug will fit in a polarized outlet only one way. If the plug does not fully fit in
the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use with an
extension cord unless plug can be fully inserted. Do not alter the plug.
-For your safety, please read instructions carefully and completely before beginning assembly
or installation.
-Product must be installed according to applicable code(s) by a person familiar with its construction
and operation.
-This Lamp rated up to 60 Watt MAX Type A INCANDESCENT Bulb (Not Included).
WARNING:
-Deviation from assembly instructions may cause risk of fire or electric shock.
-To reduce risk of personal injury, always turn off fixture and allow bulbs to cool prior to
replacement.
-Do not touch or look directly at illuminated bulbs.
-Keep flammable material away from illuminated bulbs.
PRODUCTS ARENOT INTENDED MADE IN INDIA
FOR COMMERCIAL USE. Page 1 of 4

Assemble in location for intended use.
Remove all parts, hardware and protective packaging from
carton and carefully arrange on a clean, level surface.
Harp and Finial
HardwarePacket
Recommended Location for Use: Dry Indoor Environment
Assembly Time: 15 Minutes
Required Tools: Phillips Screwdriver, Drill with 3/8” bit, Small Hammer,
Pencil, Level
PARTS
Check to make sure you have the following:
1 - Fixture Body w/attached Cord & Covers (A)
2 - Mounting Screws (B)
3 - Backplate Side Screws (C)
1 - Harp (F)
1 - Mounting Bracket (D)
1 - Finial (G)
2 - Wall Anchors (E)
Page 2 of 4
Prevent accidentally discarding small parts or
hardware. Retain all carton contents until assembly
and installation are complete.
Critical
Radius
Side
of Shade
UL Standard requires shade to be open
on both top and bottom.
Critical Radius is distance between
bulb center and side of shade. For this
lamp it should NOT be less than 2 1/2”
WARNING
FIRE HAZARD
NOT INCLUDED:
1 - 60 Watt Max
Type A Bulb
*LED may be used.

Lamp is provided optimal support when
attached directly to a WALL STUD.
*NOTICE
Unplug lamp prior to installation or removal. Turning off switch is not sufficient.
STEP 1: PREPARE FIXTURE
Carefully align Cord Covers then thread and
tighten together. Gently pull excess cord
through bottom Cover.
STEP 2: PREPARE MOUNTING HARDWARE
Carefully Remove Backplate Side Screws (C)
from sides of Fixture Body (A) and set aside.
Separate Mounting Bracket (D) inside Fixture
Backplate.
STEP 3: INSTALL MOUNTING BRACKET
Determine installation location then use Mounting
Bracket (D) and pencil to mark for both Key Holes
in Bracket.
If holes are located over a *Wall Stud, drive
Mounting Screws (B) directly into Stud.
If holes are in open drywall, use Wall Anchors (E)
with Mounting Screws.
Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 3 of 4
(C)
(A)
(D)
1 Mark location.Drill small pilot hole with 3/8” bit.
2 Gently tap Anchor into pilot hole.
3 Add item/Align holes. Add/tighten screw.
INSTALLING WALL ANCHORS
Cord Covers

TIP
CONSIDER USING LED BULBS
Lower Energy Consumption
Minimal Heat / Longer Life / High Illumination
Unplug lamp prior to installation or removal. Turning off switch is not sufficient.
STEP 4: INSTALL FIXTURE
Carefully raise Fixture Body (A) to Mounting
Bracket (D). Align holes in each side of Backplate
with threaded holes in each side of Mounting
Bracket. Insert and tighten Backplate Side
Screws (C) using a Phillips screwdriver.
STEP 5: COMPLETE FIXTURE ASSEMBLY
Gently insert and tighten bulb, attach Harp (F) to
Saddle then add Shade (not included) followed
by Finial (G).
Socket is rated up to a *60 WATT MAXIMUM
Type A Medium Base Bulb. LED/CFL may be
used. To mimic the color of an incandescent,
choose 2700K Soft White.
*NOTE: To obtain greater light ouput without
exceeding the socket wattage limitation, consider
using an LED bulb which uses approximately a
tenth of energy used by a standard incandescent.
See below:
Light
Output
(Lumens)
Energy Consumption
(Watts)
LED
Incandescent
450
4-5
40
800
6-8
60
1,100
9-13
75
1,600
16-20
100
2,600
25-28
150
Page 4 of 4
(D)
(C)
(A)
(G)
(F)
Saddle
Cleaning and Care
Periodically wipe Fixture with a soft, dry cloth.
Avoid harsh or abrasive chemicals as
finish damage may result.