B&Q CSS1354 User manual

Before you Start …
Build the unit close to where it will be used. Handle all items carefully. Always lay panels
down on a flat smooth surface. Complete each stage before moving onto the next one.
Follow these guidelines and take your time.
If any parts are missing, please call the Helpline on 01769 575500 and our team will get
things sorted.
Cross Head Screwdriver
Drill
Level
2.5mm
Drill Bit
5mm
Drill Bit
1 x Fixed Shelf
3 x LH Drawer Side
3 x RH Drawer Side
3 x Drawer Back
3 x Drawer Base
1
2
3
4
5
Panels Hardware
ASSEMBLY GUIDE
Minimum Tools required
Hammer
12 x C
3 x E
Fitted
Bedroom
Range
6 x G
4 x H
Flat Head Screwdriver
Please use scissors to open the
bag of fittings and then empty
the contents into a bowl so
that they do not get lost!
6 x O
4 x P
Handles, Handle Screws, Drawers &Doors are
supplied independently and not covered by this guide.
12 x D
PLEASE keep all fittings away from young children
Bradawl
Scissors
Tape Measure
Please build your Single
Wardrobe before following
this guide
12 x X
1 x Z
1
2
3
4
5
2
3
4
5
2
3
4
5
COMBI PACK
WARDROBE
SINGLE
Soft Close
12 x C18 x D12mm
3 x AP
3 x AR
6 x AS
10mm
3 x
3 x
3 x
3 x
AE
AF
AG
AH

1371mm
B
A
1371mm
B
A
Carefully fit 2 x part to the RH side panel, as shown. Then fit 3 x drawer
runners to the RH side panel, using screws (10mm), as shown.
Then fit 3 x hinge plates as shown (ensuring the arrow is pointing
towards the front edge of the panel). The hinge plates can be fitted to
either the LH side panel or the RH side panel, as required. In this example,
they have been fitted to the RH side panel.
Now repeat this process using the remaining part , and 3 x drawer
runners , for the LH side panel.
1
F551
Tight
against
panel
F139
Tight
against
panel
H
Hinto hole 14
into
hole 17
P
P
P
1
Lower the shelf on to the
protruding Cam legs in the
Wardrobe side.
Gently ‘push’ down until the
panel ‘clicks’ into place.
Fitting of Drawer runners
H
into holes
20 and 21
into holes
35 and 36
into holes
52 and 53
AG
D
H
AG
H
2Fitting of Fixed Shelf
3Fitting of Door Stops
Now fit the doorstops , as shown.
Z
Z
Z
Using 2 people, turn
the unit around.
Now fix the back
to the fixed shelf as
shown.
RH side panel
AG
D
J
J J J
AE
J J J
into hole number 1
AG into hole number 6
AG into hole number 13
RH
side
panel
J
EE
E
To fit the soft close mechanisms, place the template on top of the drawer runner with the end of the
template folded around the front face of the end panel, and mark the positions for the first two holes.
Carefully drill the first two holes using a 5mm drill bit, to a depth of 12mm, and then fix the soft
closer mechanism, using screws (12mm), so that it sits parallel with the drawer runner.
Finally, carefully drill the back hole, as before, and then secure.
Repeat this process for all 6 drawer runners.
D
P
P
CSS1354 02/10*

will be on the outside surface
of the Right Drawer Side.
4Construction of Drawers
Before fitting the Cam Legs to your Drawer Fronts you will have to drill the holes required for the Handles
you have purchased separately. Drill through the appropriate pilot hole(s) for the Handles you have
purchased.
We do not recommend the use of Power Screwdrivers as they can too easily drive the Screws at an angle
causing them to breakout of the panel, and it is too easy to over tighten the Screws and strip the threads
formed in the chipboard.
PILOT HOLES.
HANDLE FIXING INSTRUCTIONS IMPORTANT NOTE:
From the REAR FACE of the Drawers drill through the
holes using a 2.5mm diameter drill. From the FRONT
FACE of the Drawers, open out the 2.5mm diameter
holes using a 5mm drill. Screw Handles to Drawer Fronts.
Screw the Cam Legs into the holes shown.
X
GG
G
X
X
X2
3
5
4
3
4
2
3
4
Fit the LH , and RH , drawer sides to the drawer back , using screws as shown.
Now slide the drawer base into place as shown.
2 3 4X
5
will be on the
outside surface of
the Left Drawer Side.
O
O
Then fit cams into panels
and , as shown, ensuring
that the arrow is pointing
towards the drawer front.
O
Repeat for other 2 Drawers.
5Fitting of Draw Runners to Drawers
4
3
2
5
Position each runner onto drawer bottom, as
shown, flush to the back of the drawer front.
Then use a bradawl to mark the two holes as
indicated.
Secure with screws , as shown.
Now repeat for the other two drawers.
C
C
C
C
C
4
5
3
2
3
O
Now fit the drawer front onto
drawer sides and , and
tighten cams clockwise.
2 3
AF
AH

B&Q plc, Chandlers Ford, Hampshire, SO53 3YX.
Visit us at www.diy.com
That’s the Single Wardrobe Combi Pack completed.
Take care of your unit by using a damp cloth to clean it.
Fit the Hinge Covers F306
over the Hinges.
Recycling – the packaging materials for this
product may be recycled through your local
recycling centre. When you want to dispose of
the product itself, please consider donating it
to a local charitable organisation, otherwise
recycle it through your local recycling centre.
F676
Recycling – the packaging materials for this product may be recycled through your local recycling centre. When you want to dispose
of the product itself, please consider donating it to a local charitable organisation, otherwise recycle it through your local recycling centre.
Ensure your unit
is level before you
attempt to fit your
Doors.
Fitting of Drawers to Unit
7
Turn the drawer over and locate the wheels on
the drawer over the wheels fitted in the unit and
push into position.
Fitting of Soft Close Bracket to Drawer Sides
6
The soft close brackets should be
fitted to both of the drawer sides,
using screws as shown.
C
4
5
3
AS
Door Hinges
8
Handle Fixing
From the rear face of the Door, drill
through the holes using a 2.5mm
diameter drill.
From the front face of the Door,
open out the 2.5mm diameter holes
using a 5mm drill.
Screw Handles to Doors with the
Screws provided.
Insert the Hinges into the large
holes in the Doors and secure into
place using Screws .
Stick the Door Buffers onto
the bottom corners of the Doors
opposite to the Hinges.
Before fitting the Hinges to your Door you will have to drill the hole(s) required
through the appropriate pilot holes for the Handles you have purchased.
PILOT
HOLES
Q
Q
Q
S
S
S
S
C
Q
Fit the Hinge Covers
over the Hinges.
K
Push hook on the Hinge Arm underneath the Hinge Plate.
Press front of Hinge Arm down onto Hinge Plate until it
‘clicks’ into place.
Before adjusting the Doors, use a spirit level to
check the Base (or Top) of the unit is level front-to-
back and side-to-side in the three positions shown.
Height: Loosen screws ‘A’ on fixing
plates and move Door up or down as
required. Retighten screws ‘A’.
A
A
B
C
CLICK!
A A
B
C
CLICK!
Make the unit level BEFORE making any adjustment to
the hinges as shown.
Forward or Backwards: Loosen
screw ‘B’ on fixing plate and move
Door in or out as required. Retighten
screw ‘B’.
Sideways: To move Door ‘OUT’ at
hinge position, slacken screw ‘C’.
To move Door ‘IN’ at hinge position,
tighten screw ‘C’.
A
A
B
C
CLICK!
A
A
B
C
CLICK!
A
A
B
C
CLICK!
K
S
CSS1354 02/10*