BANGGOOD W3230 User manual

W3230 温度控制器使用说明书
温度控制范围：-55℃~120℃
温控精度：0.1℃
显示颜色：红色+蓝色
工作电源：DC12V DC 24V AC110V~220V
传感器：NTC 10K 1 米（含探头）
产品尺寸：79.2mm×41.9mm×26.3mm
开孔尺寸：72.1mm×39.2mm
产品重量：52g（12V/24V）,59g（110V~220V）
操作及显示面板
代码
项目
设定范围
出厂设置
P0
加热/制冷
H/C
//
C
P1
回差
0.1℃~30℃
0.1℃
P2
设置温度上限
-55℃~120℃
120℃
P3
设置温度下限
-55℃~120℃
120℃
P4
温度校正
-10℃~10℃
0℃/0℉
P5
延时启动
0-10 分钟
0
P6
高温警报
-55℃~120℃
120℃
P7
数据锁定
ON/OFF
OFF
P8
恢复出厂设定
ON/OFF
OFF
警告代码
代码
原因
解决方案
HHH
温度超过报警温度
温度下降至报警温度以下恢复正常
LLL
检测不到温度传感器
更换货重新连接温度传感器
操作指南
1、短按“SET”小数码管闪烁，按“△”或“▽”设置目标温度，按“待机”键或
3秒内无操作保存设置。
2、长按“SET”进入代码设置模式，按“△”或“▽”切换代码，选定后短按
“SET”进入代码设置，设置后按“待机”键或 3秒内无操作保存设置。
3、停机后默认保存最后一次参数设置。
4、恢复出厂设置：按住“SET”通电。
5、模块通电时直接启动，通电后长按“待机”键，模块进入“休眠”或“唤醒”；
如遇停电，电力恢复后模块自动运行，无需人工启动。
**工作电源电压务必按照标签标准电压接入，否则容易损坏模块。

W3230 Temperature controller instruction manual
Temperature control range: -55°C~120°C
Temperature control accuracy: 0.1 °C
Display color: red + blue
Working power supply: DC12V DC 24V AC110V~220V
Sensor: NTC 10K 1 meter (with probe)
Product Size: 79.2mm×41.9mm×26.3mm
Hole Size: 72.1mm×39.2mm
product weight: 52g（12V/24V）,59g（110V~220V）
Operation and display panel
Code
Function
Set range
Default
P0
Heat/Cool
H/C
//
C
P1
Backlash
0.1℃~30℃
0.1℃
P2
Set upper limit
-55℃~120℃
120℃
P3
Set lower limit
-55℃~120℃
120℃
P4
Calibration
-10℃~10℃
0℃
P5
Delayed start
0-10min
0
P6
Alarm temperature
-55℃~120℃
120℃
P7
Data lock
ON/OFF
OFF
P8
Factory reset
ON/OFF
OFF
Warning code
Code
Reason for error
Solution
HHH
Temperature exceeds
alarm temperature
The temperature drops below the alarm
temperature and returns to normal.
LLL
No temperature
sensor detected
Replacement reconnect temperature sensor
Operation guide
1. Short press “SET” small digital tube to flash, press “△” or
“▽” to set the target temperature, press “Standby” button or no
operation to save the setting within 3 seconds.
2. Press and hold “SET” to enter the code setting mode, press “△” or
“▽” to switch the code. After selecting, press “SET” to enter the
code setting. After setting, press “Standby” button or no operation to
save the setting within 3 seconds. .
3. The last parameter setting is saved by default after shutdown.
4, restore the factory settings: press and hold "SET" to power on.
5. When the module is powered on, it will start directly. After power-on,
press and hold the “standby” button, the module will enter “sleep” or
“wake up”; in case of power failure, the module will run automatically
after power recovery, no need to start manually.
**The working power supply voltage must be connected
according to the standard voltage of the label,
otherwise the module will be damaged easily.