Barco R9898170 User manual

BARCOPROJECTIONSYSTEMS
R9898170
R9898171
Date:21.02..2001
INSTALLATION MANUAL
3-D Motorized Polar Circ/Lin Kit for Reality 909
Art.No.:R5976406Rev:00
Motrized 3-D Kit
R909

Due to constant research, the information in this manual is subject to change without notice.
Produced by BARCO NV, February 2002.
All rights reserved.
Trademarks are the rights of their respective owners.
BARCOn.v./ProjectionSystems
Noordlaan5
B-8520Kuurne
Belgium
Tel:[phone]
Fax:[phone]
E-mail : [email protected]
Visite Barco at the web : http://www.barco.com
Printedin Belgium

BARCO  3  Projection Systems
Description and Contents of the kit
Purpose of the
Kit
The kit is designed to be mounted on a BarcoReality 909 projector to allow passive 3D
projection.
To be continued on next page
Kit features The kit contains a polarholder, a control module (if motorized) and the necessary cables
and fixation parts.
Both left and right channel polarizers are included in the kit. Depending on the kitnumber
ordered the polarizers may be of the linear or the circular type.
The automatic desactivation of the polarisers allows the flexixbilty of:
-using a 3D (stereo) system as a monosystem
-using a 3D passif system as an actif system
Following table gives an overview of the different kitnumbers:
Specs
&
ircular/
/
inear
0
otorized
Kit n°
R9898170
R9898171
C
L
M
M
R9898170: circular 3D Kit containing:
R763847 UNR909 FRMC PLR CIRR MTR 1
R822703 FLTR PLR GL CIRC R 200X200 2
R822702 FLTR PLR GL CIRC R 179X179 1
or:
R763846 UNR909 FRMC PLR CIRL MTR 1
R822701 FLTR PLR GL CIRC L 200X200 2
R822700 FLTR PLR GL CIRC L 179X179 1
R9898171: Linear 3D kit containing:
R763849 UNR909 FRMC PLR CIRR MTR 1
R822762 FLTR PLR GL CIRC R 200X200 2
R822761 FLTR PLR GL CIRC R 179X179 1
or:
R763848 UNR909 FRMC PLR CIRL MTR 1
R822760 FLTR PLR GL CIRC L 200X200 2
R822759 FLTR PLR GL CIRC L 179X179 1

BARCO  4  Projection Systems
Description and Contents of the kit (Continued)
Illustrations
spacers: 4 x R822171
circ: left : R822700
right: R822702
lin: left: R822759
right: R822761
circ: left : R822701
right: R822703
lin: left: R822760
right: R822762
polarizers
polarizers
Top view of the control module R763620
View of the Polar holder
Top view of the delivered cables
Z3488004
Z3484038
Z3486078

BARCO  5  Projection Systems
Mounting the polarizer frame
What has to be
done
The polarizer holder has to be mounted on the projector frame.
Necessary Tools M6 spanner (n° 10)
Mounting the
holder
To mount the holder, follow the next procedure:
1
2
1&2 (next
page)
3(next
page)
Unscrew the four bolts A of the middle lens, these bolts will
be used afterwards
tip : Unscrew them one at a time and replace them sys-
tematically with one of the delivered spacers (R822171)
Mount the polar holder on the projector, the four spacers
must be aligned with the four holes in the polar holder
Tighten the holder with the four bolts previously removed
from the lens
Step Action Image
Illustrations
Image 1
A
To be continued on next page

BARCO  6  Projection Systems
Mounting the polarizer frame (Continued)
Illustrations
Image 2
Image 3
To be continued on next page

BARCO  7  Projection Systems
A
Mounting the polarizer frame (Continued)
Illustration of the
spacers
(R822171)
mounted
Image 4
Image 5
Illustration of the
holder mounted,
(polarizers
activated)

BARCO  8  Projection Systems
Mounting the control module
What has to be
done
The module has to be mounted in the convergence drawer
Necessary Tools flat screwdriver
Mounting the
print
To mount the print, follow the next procedure:
1
2
3
4
5
6
7
1
2
3
3
4
5&6
7
Release the two handles of the drawer by pushing as
shown on the image
Pull the drawer ou of its housing
Place the print as shown on the image
Tighten the print with the 4 delivered screws.
Use the shortest yellow cable (7P) to connect the module
to the controller located as shown on the image.
Use the longest yellow cable (3P) to connect the print to
the Convergence module located as shown on the image
(connector A on image 6)
Use the cable with the BNC connectors to connect the
module (DIN connector side) to the motor (BNCs side)
Step Action Image
Illustrations
Image 2 Image 3
A
Image 1

BARCO  9  Projection Systems
Mounting the control module (Continued)
Illustrations
A
Image 4 Image 5
Image 6

BARCO  10  Projection Systems
Mounting the control module (Continued)
Illustration of the
motor connection
Image 7