Barricade R108980 User manual

PIONEER RUNNING BOARDS
2019 DODGE RAM 1500 QUAD CAB
Page 1 of 3 6/12/18 (DP)
PARTS LIST:
1
Driver/left side Pioneer Running Board
12
6mm x 20mm T-Bolts
1
Passenger/right side Running Board
12
6mm x 22mm x 2mm Flat Washers
6
Universal Mounting Brackets (left or right)
12
6mm Lock Washers
18
8mm x 24mm x 2mm Washers
12
6mm Hex Nuts
18
8-1.25mm Nylon Lock Nuts
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.
1. Start the installation under the driver side of the vehicle. Locate the front (3) factory studs along the
inner side of the body panel, (Figure 1). Use a wire brush or thread chaser die to remove excess paint
or undercoating from threaded studs as necessary.
2. Select (1) Mounting Bracket. NOTE: All (6) Brackets are universal and will fit left or right side. Attach
the Mounting Bracket to the (3) factory studs with (3) 8mm Flat Washers and (3) 8mm Nylon Lock Nuts,
(Figure 2). Leave brackets loose at this time.
3. Repeat Steps 1 & 2 to install the Universal Brackets in the center and rear mounting locations along
the body panel, (Figures 3 & 4).
4. Carefully unwrap and select the Driver/left side Running Board. Use the illustration above to help
determine the correct Running Board. Place the Running Board on top of the Brackets. Locate the
channel openings in the bottom of the Running Board. Select (6) 6mm T-Bolts, (Figure 5). Insert the T-
Bolts into the channels in the bottom of the Running Board closest to the Brackets, (Figure 6). Lift the
Running Board up and guide the studs through the Brackets.
5. Attach the Running Board to the Brackets with (6) 6mm Flat Washers, (6) 6mm Lock Washers and (6)
6mm Hex Nuts, (Figures 7 & 8). NOTE: The Running Board is designed to fit close to the vehicle. It
may be necessary to loosen the Bracket hardware slightly and tilt the Brackets downward to insert the
Running Board between the Brackets and the body.
6. Level and adjust the Running Board as necessary and fully tighten all hardware.
7. Repeat Steps 1—6for Passenger/right side Running Board Installation.
8. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
(6) Left or Right
Mounting Brackets
Driver/left side
Running Board
Front
NOTE: The front of the Running
Board is triangular shaped.

PIONEER RUNNING BOARDS
2019 DODGE RAM 1500 QUAD CAB
Page 2 of 3 6/12/18 (DP)
To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer
over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap
may be used also to clean the Running Board.
Driver/left Side Installation Pictured
Front
Front
(Fig 1) Driver/left side front mounting location
(3) 8mm Flat Washers
(3) 8mm Nylon Lock Nuts
(Fig 2) Attach Bracket to the (3) studs
(Fig 3) Driver/left side center mounting location
(Fig 4) Driver/left side rear mounting location
Rear

PIONEER RUNNING BOARDS
2019 DODGE RAM 1500 QUAD CAB
Page 3 of 3 6/12/18 (DP)
Driver/left Side Installation Pictured
(Fig 5) 6mm T-Bolt
(Fig 6) Insert 6mm T-Bolts through the channel
openings in the bottom of the Running Board
(Fig 7) Driver/left side Running Board attached
to Mounting Bracket at the front location
(2) 6mm Flat Washers
(2) 6mm Lock Washers
(2) 6mm Hex Nuts
(Fig 8) Driver/left side Running Board attached to
Mounting Brackets at the center and rear locations
(2) 6mm Flat Washers
(2) 6mm Lock Washers
(2) 6mm Hex Nuts
Front
Front
Front