Bartec LUMEN X4 User manual

ATEX / IECEx Zone 2 and 22 CSA Class I Division 2
4.3" Industry Mobile Computer
Type B7-A2P4-..../........
Lumen X4 Quick Start Guide

Quick Start Guide -Translation
Lumen X4
4.3" Industry Mobile Computer
TypeB7-A2P4-…./……..
ATEX/IECEx Zone2/22
CSA Class I Division 2
Document No.: B1-A2P4-7E0002 / 401724
Revision 0 / Status: 6 June 2016
Proviso: Subject to technical changes.
Changes, mistakes and printing errors do not
substantiate any claim to damages.
Content Page
English 1-12
BARTEC GmbH
Max
-Eyth-Straße 16
Service
-mobilecom[email protected]
www.bartec.de

Quick Start
Guide
4.3" Industry Mobile Computer- Lumen X4
Type B7-A2P4-.…/……..
Subject to technical changes.
06/2016
EN 2/12
1. Basic Information
Read carefully before putting the devices into operation.
The Quick Start Guide is a fixed part of the product. It
must be kept in the direct vicinity of the device and the
installation, operating and service staff must have
access to it at all times.
More detailed instructions of the use can be found at www.bartec.de
as well as the current versions of the datasheets, user manual,
certificates and EU declaration conformity or may be requested
directly from BARTECGmbH.
Knowledge of the safety and warning information and the strict
compliance with it is essential for safety installation and use. Atries
and material damage can be avoided by circumspect handling and
systematicallyfollowing the instructions.
The BARTEC company reserves the right to carry out technical
changes at any time.
Maintanance and Repairs The pertinent erection and operating
provisions for electrical systems must be observed! Repairs to
explosion-protected devices may only be performed by authorised
personnel with original spare parts and according to the state of the
art. The applicable provisionsmustbe observed in thisrespect.
Inspections According to EN/IEC 60079-17 and EN/IEC 60079-19,
the operator of electrical systems in potentially explosive
atmospheres is obliged to have these inspected by an electrician to
ensure correct condition.
Warranty If non-
specified components are used, the explosion
protection will no longer be guaranteed. In the case of externally
procured parts, it is not guaranteed that these have been designed
and manufactured in accordance with their loadand requisite safety.
Disposal As professional electrical devices, our devices are intended
exclusively for commercial use, so-called B2B devices, in accordance
with the WEEE Directive. Observe the
national waste disposal
regulations when disposing of the devices. All products purchased
from us can be returned to us by our customers for disposal. The
sender shallbear the costs ofpostage and packaging.

Quick Start
Guide
4.3" Industry Mobile Computer - Lumen X4
Type B7-A2P4-.…/……..
Subject to technical changes.
06/2016
EN 3/12
Safety and warning information is particularly emphasised
in this Quick Start Guide marked by symbols.
DANGER describes a directly imminent danger in
hazardous areas. If not avoided, death or severe
injury will be the consequence.
2. Scope of delivery
-
1 x 4.3" ex-certified Lumen X4
Industry Mobile Computer
-1 x Replaceable Li-Polymer battery
-1 x Hand strap
-1 x USB power adapter with EU plug
-1 x USB power adapter with US plug
-1 x USB cable (Type A to micro Type B)
-1 x Quick Start Guide
3. Getting started
In order to start using the Lumen X4 Mobile Computer for the
first time:

Install the battery
Charge the battery
Start the Lumen X4
Install SIM/Micro SD Card.

Quick Start
Guide
4.3" Industry Mobile Computer - Lumen X4
Type B7-A2P4-.…/……..
Subject to technical changes.
06/2016
EN 4/12
4. Marking, test certificate, and standards
Note: Full information in "user manual"
ATEX Zone 2 and 22
II 3G Ex ic IIC T5 Gc
II 3D Ex ic IIIB T100°C Dc IP54
-20 °C ≤ Ta ≤ +50 °C
EPS 16 ATEX 1 039X
IECEx Zone 2 and Zone 22
Ex ic IIC T5 Gc
Ex ic IIIB T100°C Dc IP54
-20 °C ≤ Ta ≤ +50 °C
IECEx EPS 16.0016X
CSA Class I Division 2
Class I Div. 2 Groups A, B, C
and D T5
CSA Certificate:
70043322
X - marking (special conditions of use for secure operation
within the potentially explosive atmosphere)
The ambient temperature range is -20 °C to +50 °C.
The device must be protected from impact with high impact
energy, from intense UV-irradiation, and strongly charge
generating processes.
It is not allowed to use connectors inside the potentially
explosive atmosphere.
It is not allowed to remove, change and/or charge the
battery inside the potentially explosive atmosphere.
Warnings
The warnings on the product and on the battery must
always be observed!
Additional safety instructions for use in potentially explosive
atmospheres, see user manual.

Quick Start
Guide
4.3" Industry Mobile Computer - Lumen X4
Type B7-A2P4-.…/……..
Subject to technical changes.
06/2016
EN 5/12
5. Your Lumen X4
Some tips for using and caring the Lumen X4
Your Lumen X4 Mobile Computer series is designed to resist
damages from certain rugged conditions. However, to help care
for your Lumen X4, please avoid
prolonged or extreme
exposure to those conditions.
To ensure the rugged design works and protects your
Mobile Computer, please be sure the connector cover is
closed and the back cover is screwed properly.
Don’t leave your Mobile Computer near a heat source;
this can damage the device.
Avoid dropping your Mobile Computer on a hard surface;
this can potentially cause damage to the device.
To clean your Mobile Computer, use a dry soft cloth.
Don’t use alcohol or other cleaning solutions.
Please don´t bring your Mobile Computer in contact with
water when the connector cover is opened. The water-
proof design works only when the outer case is sealed
properly.
Note: Certain apps and features may not be available in
all countries.
The external interfaces "Micro USB Type B (OTG Host,
data exchange and charging), Pogo Pin (charging in
docking station)" may only be used outside the
potentially explosive range with accessories specified by
the manufacturer.
Note: Detailed functionality illustration in the user manual.

Quick Start
Guide
4.3" Industry Mobile Computer - Lumen X4
Type B7-A2P4-.…/……..
Subject to technical changes.
06/2016
EN 6/12
6. Starting the Lumen X4
Before using the Lumen X4, install the Li-Polymer battery
by sliding the battery into the Lumen X4.

Quick Start
Guide
4.3" Industry Mobile Computer - Lumen X4
Type B7-A2P4-.…/……..
Subject to technical changes.
06/2016
EN 7/12

Quick Start
Guide
4.3" Industry Mobile Computer - Lumen X4
Type B7-A2P4-.…/……..
Subject to technical changes.
06/2016
EN 8/12
7. Installing the Battery
Only charge, install or replace the battery outside the
potentially explosive atmosphere.
(1) Reinsert the battery by
latching the bottom first.
(2) Push it down.
(3) Check the locking of the
battery latches. The
slides of the battery
latches must maintain the
position in the drawing
(see arrows)

Quick Start
Guide
4.3" Industry Mobile Computer - Lumen X4
Type B7-A2P4-.…/……..
Subject to technical changes.
06/2016
EN 9/12
8. Charge the Battery
With USB charging cable
The battery in the new Lumen X4 is not charged yet. For the
first time using, we recommend you charge with the AC adapter
(Charging from PC’s USB port will take 6 hours or longer). Use
the bundled AC adapter and USB cable to charge the Mobile
Computer for 4hrs until the LED indicator turns solid green.
Do not replace or charge the battery in a potentially
explosive atmosphere.
Only use original accessories from BARTEC.
Our warranty does not cover damage to the Lumen
X4 caused by other batteries and/or chargers.
Additional safety instructions for use in potentially
explosive atmospheres, see user manual.
Note: The actual life of a battery is influenced by different
factors, e.g. hot, cold, rough operating environment and
falling from a great height. Batteries kept for a duration
of six months or longer should be charged and
discharged again at least every three months.
Please don’t remove the battery pack or try to take the
Mobile Computer apart while the Lumen X4 is charging.
These actions will result in some damages and may
invalidate your warranty.

Quick Start
Guide
4.3" Industry Mobile Computer - Lumen X4
Type B7-A2P4-.…/……..
Subject to technical changes.
06/2016
EN 10/12
(1) Connect the power supply
output connector to the
input power port on the USB
charging cable.
(2) Open the connector cover
and connect the USB
charging cable to the
bottom of the Industry
Mobile Computer.
The battery charge LED
indicates the battery
charging status.
LED Status Description
Off
The Industry Mobile Computer is not
charging or not properly connected
Solid red
Low battery
Solid orange
Charging in progress
Solid green
Charging complete

Quick Start
Guide
4.3" Industry Mobile Computer - Lumen X4
Type B7-A2P4-.…/……..
Subject to technical changes.
06/2016
EN 11/12
9. Turn on/Turn off your Lumen X4
Unintended use endangers explosion protection. Risk
of fatal injury in an explosive atmosphere!
In the case of functional disturbances or damage to
the enclosure, the device should be turned off and
removed immediately from the potentially explosive
atmosphere to a safe place. Remove battery to
decommission the device!
The ambient temperature range of use for secure
operation within the potentially explosive atmosphere
is -20 °C to +50 °C.
Additional safety instructions for use
in potentially
explosive atmospheres, see user manual.
Turn on:
(1) Press and hold the Power
On/Off button for 3 seconds,
located on the right side of
the device.
(2)
When the device vibrates,
release the Power On/Off
button. The desktop screen
is displayed.
Turn off:
(1) To turn off the device, press
and hold the Power On/Off
button until the phone
options menu appears.
(2) Tap Power off.

Quick Start
Guide
4.3" Industry Mobile Computer - Lumen X4
Type B7-A2P4-.…/……..
Subject to technical changes.
06/2016
EN 12/12
10.How to Insert SIM / Micro SD Card
Only insert or replace the SIM/Micro SD card outside
of the potentially explosive atmosphere. Only use
micro SD cards which have been tested and certified
by BARTEC for this purpose.
(1) Turn Off the Lumen X4.
(2) Make sure the Lumen X4 is
powered off and the USB cable
is unconnected before you
remove the back cover.
(3) Place the Lumen X4 on its front
(display facing down-wards) on
a flat mat.
(4) Press the two latches up.
(5) Remove the battery.
(6) Insert the SIM card in the SIM
card slot (with the gold contacts
facing downwards and cut-off
corner facing out) in the
direction of the arrow.
(7) Push the micro SD card holder
in the direction of the arrow to
unlock it.
(8) Pull the micro SD card holder
upwards and bring it in a vertical
position.
(9) Put the micro SD card into the
slot.
(10) Close the SD card holder and
push it into lock position until
there is a click.

Quick Start
Guide
4.3" Industry Mobile Computer - Lumen X4
Type B7-A2P4-.…/……..
EU Declaration of Conformity

Quick Start
Guide
4.3" Industry Mobile Computer - Lumen X4
Type B7-A2P4-.…/……..

EN_B1-A2P4-7E0002-06/2016-Automation-401724
Your partner
for safety
technology.
Challenge us!
BARTEC GmbH
Max-Eyth-Str. 16
97980 Bad Mergentheim
Germany
Phone: [phone]
Fax: [phone]
[email protected]
www.bartec.de